Accessories - Maytag MVWB980BG Use And Care Manual

Top-loading high efficiency low-water washer
Hide thumbs Also See for MVWB980BG:
Table of Contents

Advertisement

Available languages

Available languages

TROUBLESHOOTING
First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.
If you experience
Error Code Appears in Display
oL (overloaded)
appears in display
uL (unbalanced load)
appears in display
LF (too long to fill)
appears in display
Ld (too long to drain
water) appears in display
HC (Hot and Cold
hoses reversed)
appears in display
Sd (Excess suds)
appears in display
dL (Lid cannot lock)
appears in display
lid (Lid opened)
appears in display
dU (Lid cannot unlock)
appears in display
F## code (F-type
error code) appears
in display
Fd (Factory Default)

ACCESSORIES

See Installation Instructions for installation accessories
Part Number:
8212526
31682
1903WH
In U.S.A. www.maytag.com/product_help – In Canada www.maytag.ca.
Possible Causes
Load too large.
Load not balanced. The washer is
running a load-balance correction
routine.
Washer taking too long to fill.
Drain extends more than
4.5" (114 mm) into standpipe.
Washer taking too long to drain
water. Drain extends more than
4.5" (114 mm) into standpipe.
Hot and cold inlet hoses have been
installed incorrectly.
Excessive suds in washer. Washer is
running a suds reduction routine.
An item in the load may be keeping the
lid from locking.
Washer lid left open.
Objects on washer lid prevent it from
unlocking.
System error code.
Washer sets back to factory default.
Accessory
Washer drip tray, fits under all
All-purpose appliance cleaner
Laundry supply storage cart
If an overload is detected, the washer will drain any water and
detergent in the washer. Remove several items and add HE
detergent. Close lid and press START/PAUSE.
Allow the washer to continue. If the dial is flashing and the washer
has stopped, redistribute the load, close the lid, and press START/
PAUSE.
Check plumbing for correct drain hose installation. Use drain hose
form and attach securely to drainpipe or tub. Do not tape over drain
opening. See Installation Instructions.
Check plumbing for correct drain hose installation. Use drain hose
form and attach securely to drainpipe or tub. Do not tape over drain
opening. See Installation Instructions.
Lower drain hose if the end is higher than 96" (2.4 m) above
the floor. Remove any clogs from drain hose. See Installation
Instructions.
This code will appear at the end of the wash cycle to indicate that
cold water hose is connected to the hot water inlet and hot water
hose is connected to the cold water inlet.
Allow the washer to continue. Use only HE detergent.
Always measure detergent, and base detergent quantity on
load size. Follow detergent manufacturer's instructions. If the dial is
flashing, reselect your desired cycle using a cold wash temperature,
and press START/PAUSE. Do not add detergent.
Check for items directly under the lid.
Close the lid to clear the display. If the lid is left open for more than
10 minutes, the cycle will reset and water in the washer
will drain.
Remove objects, such as a basket of laundry, from the top of the
washer.
Press START/PAUSE once to clear the code. Then press
START/PAUSE again to restart washer. If code appears again,
call for service.
To return all options and modifiers to Factory Default, press
POWER/CANCEL, select RINSE/DRAIN & SPIN cycle, and then
press EXTRA RINSE, FABRIC SOFTENER, EXTRA RINSE, FABRIC
SOFTENER within 5 seconds. When done correctly, the display
shows "Fd" for 3 seconds and then unit returns to Standby Mode.
Solution
19

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Mvwb980bwBravos xl

Table of Contents