Onkyo DTR-40.2 Instruction Manual page 95

■
The beginning of audio received by an HDMI IN
can't be heard
Since it takes longer to identify the format of an
HDMI signal than it does for other digital audio sig-
nals, audio output may not start immediately.
Video
■
There's no picture
Make sure that all video connecting plugs are pushed
in all the way.
Make sure that each video component is properly
connected.
If your TV is connected to the HDMI output, select
"- - - - -" in the "HDMI Input" setup to watch com-
posite video, and component video sources.
If the video source is connected to a component
video input, you must assign that input to an input
selector, and your TV must be connected to either
the HDMI output or COMPONENT VIDEO MON-
ITOR OUT.
If the video source is connected to a composite video
input, your TV must be connected to the HDMI out-
put or the corresponding composite video output.
If the video source is connected to an HDMI input,
you must assign that input to an input selector, and
your TV must be connected to the HDMI output.
On your TV, make sure that the video input to which
the AV receiver is connected is selected.
■
There's no picture from a source connected to
an HDMI IN
Reliable operation with an HDMI-to-DVI adapter is
not guaranteed. In addition, video signals from a PC
are not guaranteed.
When the Resolution is set to any resolution not sup-
ported by the TV, no video is output by the HDMI
outputs.
If the message "Resolution Error" appears on the
AV receiver's display, this indicates that your TV
does not support the current video resolution and
you need to select another resolution on your DVD
player.
■
The on-screen menus don't appear
(Australian models) Specify the TV system used in
your area in the TV Format Setup.
On your TV, make sure that the video input to which
the AV receiver is connected is selected.
When the AV receiver doesn't connect TV with
HDMI, onscreen menus are not displayed.
■
The picture is distorted
(Australian models) Specify the TV system used in
your area in the TV Format.
■
The on screen display does not appear
Depending on the input signal, the on screen display
may not appear when the input signal from the
HDMI IN is output to a device connected to the
HDMI output.
Tuner
■
Reception is noisy, FM stereo reception is
—
noisy, or the FM STEREO indicator doesn't light
Relocate your antenna.
Move the AV receiver away from your TV or com-
puter.
Listen to the station in mono.
When listening to an AM station, operating the
remote controller may cause noise.
17
Passing cars and airplanes can cause interference.
18, 19,
Concrete walls weaken radio signals.
83
If nothing improves the reception, install an outdoor
49
antenna.
Remote Controller
19, 49
■
The remote controller doesn't work
Before operating this unit, be sure to press
Receiver.
19
Make sure that the batteries are installed with the
correct polarity.
Install new batteries. Don't mix different types of
18, 49
batteries, or old and new batteries.
Make sure that the remote controller is not too far
away from the AV receiver, and that there's no
—
obstruction between the remote controller and the
AV receiver's remote control sensor.
Make sure that the AV receiver is not subjected to
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.
If the AV receiver is installed in a rack or cabinet
100
with colored-glass doors, the remote controller may
not work reliably when the doors are closed.
Make sure you've selected the correct remote con-
49
troller mode.
When using the remote controller to control other
manufacturers' AV components, some buttons may
—
not work as expected.
Make sure you've entered the correct remote control
code.
Make sure to set the same ID on both the AV receiver
and remote controller.
■
Can't control other components
60
If it's an Integra/Onkyo component, make sure that
—
the cable and analog audio cable are connected
properly. Connecting only an
—
Make sure you've selected the correct remote con-
troller mode.
If you've connected a cassette tape deck, to the TV/
CD IN jack, or an RI Dock to the TV/CD IN or
GAME IN or VCR/DVR IN jacks, for the remote
60
controller to work properly, you must set the input
display.
If you cannot operate it, you will need to enter the
appropriate remote control code.
60
To control another manufacturer's component, point
the remote controller at that component.
If none of the codes work, use the Learning function
to learn the commands of the other component's
remote controller.
—
—
31
—
—
—
—
—
4
4
4
—
—
11, 89
—
88
60
20
cable won't work.
11, 89
27
88
88
91
En
95