Adjusting Screen Brightness; Ccd-Raw; Ã Playback Volume - FujiFilm FinePix FinePix S9600 Owner's Manual

SET-UP
ã PLAYBACK VOLUME
0 1 1 2 3 4 5 6 8 9 1 0 1 0
7
SET SET CANCEL CANCEL
0 1 2 0
é FRAME NO.
< > <
CONT. RENEW
0001 0001
A A
0005 0005
0006 0001
B B
0010 0005
Formatted media used for both A and B.
100-0001
Directory number
File number
Frame number
6/24/2006 10:00 AM
102 102
✽ How to use the SET-UP menu (➡P.98)
Adjust volume while playing back movie and voice
memo.
1 Press "d" or "c" to adjust the volume. The
larger the number, the larger the volume is
emitted. "0" indicates a sound deadening.
2 Press the "MENU/OK" button to confirm the new
setting.
Specifies whether frame numbers are assigned
consecutively from previous numbers or begin
>
again.
CONT.: Pictures are stored beginning from the
highest file number stored on the last
media used.
RENEW: Pictures are stored on each media
beginning with a file number "0001".
Setting this function to "CONT." makes file
management easier as it makes sure that file
names are not duplicated when images are
downloaded to a PC.
●
!
When the camera settings are " ú RESET", the frame
number setting ("CONT." or "RENEW") is changed to
"CONT." and the frame number itself does not return to
"0001".
●
!
When the media already contains image files with file
numbers higher than the highest file number on the last
media, images are stored beginning from the highest file
number on the current media.
Check the file number by viewing the image. The
last 4 digits of the 7-digit number in the top right
corner of the screen are the file numbers, while the
first 3 digits show the directory number.
●
!
When changing the media, always turn the camera off before
opening the slot cover. Opening the slot cover without turning
the camera off may cause the frame number memory to not
function.
●
!
File number runs from 0001 to 9999. Once 9999 is exceeded,
the directory number changes from 100 to 101. The
maximum number is 999-9999.
●
!
The displayed frame number may differ for images
photographed on other cameras.
●
!
When [FRAME NO. FULL] appears, see P.142.
ê ADJUSTING SCREEN BRIGHTNESS
5 - 4 4 3 2 1 1 2 3 4 5 +
0
SET SET CANCEL CANCEL
1 0 2 0

≤ CCD-RAW

Setting CCD-RAW to ON disables the signal processing functions (reconstituting the data received
from the CCD as an image) performed on the camera. Consequently, this task must be performed
on the PC.
Conversion using FinePixViewer also provides a simple way to create TIFF-format images.
Conversion using Hyper-Utility2 also provides you to specify parameters such as image format,
tone, white balance, sharpness, saturation, and brightness during file conversion.
✽ To rebuild images, FinePixViewer (on the bundled CD-ROM "Software for FinePix CX") or Hyper-Utility2 (on the bundled
CD-ROM "Hyper-Utility Software HS-V2") must be installed on your PC.
■ The functions listed below cannot be used in CCD-RAW mode.
During shooting
Digital zoom, Continuous shooting and Quality are unavailable.
During playback Playback can be zoomed up to 2.5×, but cropped images cannot be saved.
To adjust screen brightness:
1 Press "d " or "c " to adjust the screen
brightness.
2 Press the "MENU/OK" button to confirm the new
setting.
4
103