Planet ADE-3110 User Manual
  1. Manuals
  2. Brands
  3. Planet Manuals
  4. Network Router
  5. ADE-3110
  6. User manual

Planet ADE-3110 User Manual

Adsl modem router
Hide thumbs
Table of Contents

Advertisement

Quick Links

ADSL Modem Router
ADE-3110
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for Planet ADE-3110

Summary of Contents for Planet ADE-3110

  • Page 1 ADSL Modem Router ADE-3110 User’s Manual...

  • Page 2: Fcc Compliance Statement

    PLANET Technology. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environ- ments and applications, and makes no warranty and representation, either implied or ex- pressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.

  • Page 3: Ce Mark Warning

    Trademarks The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous hardware and software products by their trade names. In most, if not all cases, these designations are claimed as trademarks or registered trademarks by their respective companies.

  • Page 4: Table Of Contents

    ABLE OF ONTENTS 1. I ........................1 NTRODUCTION 1.1 Features .............................. 1 1.2 System Requirements ......................... 2 2. K ....................3 NOWING OUTER 2.1 Front Panels ............................3 2.2 Rear Panels............................3 2.3 LED Indicators ............................. 4 3. L ..........................5 OGIN 4.
  • Page 5 6.1 WAN Status ............................39 6.2 ATM Status ............................39 6.3 ADSL Configuration ........................... 40 6.4 Route Table ............................41 6.4.1 System Default Gateway Configuration ....................43 6.4.2 Route Configuration ..........................43 6.5 Learned MAC Table........................... 44 6.6 RIP Configuration ..........................44 6.6.1 RIP Per Interface Configuration ......................

  • Page 6: Introduction

    1. Introduction This Router is a highly integrated, cost-effective solution. All setup and provisioning is ac- complished via a simple intuitive Web interface which further enhances the user experi- ence. 1.1 Features ADSL Compliance Compliant with ADSL standards u Full-rate ANSI T1.413 Issue 2 and ITU G.dmt (G.992.1) standards u Splitterless ITU G.lite (G.992.2) specification u ADSL over POTS (Annex A) and ADSL over ISDN (Annex B) DMT modulation and demodulation...

  • Page 7: System Requirements

    1.2 System Requirements Pentium III 266 MHz processor minimum 128 MB RAM minimum 20 MB of free disk space minimum Ethernet Network Interface Controller (NIC) RJ45 Port Internet Browser Ethernet (CAT5) Cable...

  • Page 8: Knowing Your Router

    2. Knowing Your Router When selecting the location for the Router, allow room to access the connections on the rear panel. You will want to place the Router so that you will be able to see the LED indi- cators on the front panel. It may be convenient for you locate the Router near the PC you intend to use for initial configuration of the Router.

  • Page 9: Led Indicators

    well as the port connections. ADSL 15V DC RESET RESET button: The Router comes with a reset button built into the rear panel. Use this button to restore the factory default settings. If you need to reset the Router, press the reset button for 2-3 seconds and then release it.

  • Page 10: Login

    3. Login There are two levels of access rights/privileges for the Router: Administrator: User name admin, the administrator account has complete read/write access on all pages (Status, Configuration, Admin Privilege, and Firewall Configuration). Admin account also has FTP server access. User: User name user, the User account has read/write access to pages under the Status and Configuration sections.
  • Page 11 Remember my password checkbox: By default, this box is not checked. Users can check this box so that Internet Explorer will remember the User name and Password for future logins. It is recommended to leave this box unchecked for security purposes. Admin and User passwords can be changed after login.

  • Page 12: Status

    4. Status Pages The links under the Status column are associated with the pages that represent the status of system (computer and Router) and interfaces (connections). This includes LAN, WAN, DHCP, PPP, and ADSL status. These pages can be viewed and modified by both user and admin accounts.

  • Page 13: Ppp Page

    the LAN interface. The total number of available interfaces is the amount of computers that are able to hook up to the DHCP Server. Number of Ethernet Devices Connected to the DHCP Server: It displays the DHCP client table with the assigned IP addresses and MAC addresses. If there are no devices connected to the DHCP server, then a table will not appear, otherwise a table listing all devices con- nected to DHCP server will appear on the bottom of the page.
  • Page 14 PPP (Point-to-Point Protocol): The table displays the following fields: Connection Name: This is user defined. User defined connections for PPP can be created in PPP Configuration page. Interface: States the interface that is being used (PVC0 ... PVC7). Mode: There are two available modes for the connection: PPP over Ethernet (PPPoE) PPP over ATM (PPPoA) Status: States whether PPP connection is Connected or Not Connected.

  • Page 15: Adsl Page

    Connect and Disconnect: It allows you to manually connect/disconnect the PPP con- nection for each PPP interface. In other words, each PPP session can be connected and disconnected individually. Connection #: Specifies the PPP session to be connected/disconnected. Connect/Disconnect Execute: Press this button to either connect or disconnect. Connection status dialog will be displayed below the Execute button after it is pressed.
  • Page 16 Restart/Stop Execute: It allows you to stop or restart the ADSL connection by selecting the appropriate action and clicking Execute. Showtime Firmware Version: It displays the ADSL data pump firmware version. ADSL Line Status: It displays the ADSL connection process and status. The different states for this field are as follows: Activation: The Router is in this state when it is attempting to start the activation process.
  • Page 17 ADSL Startup Attempts: It displays the number of ADSL connection attempts after loss of showtime. A connection attempt is recorded only if showtime is attained. ADSL Max TX Power: It displays the transmit output power level of the CPE (Customer Premise Equipment), which is the transmit output power level of the Router.

  • Page 18: Configuration

    5. Configuration Pages The links under Configuration column are associated to the pages that represent the con- figurations of system and interfaces. These pages can be viewed and modified by both user and admin accounts. When any settings are changed, please go to the Save Set- tings page to save the new setting(s) and reboot the Router.
  • Page 19 Enable PPP Half Bridge Disabled Disabled Disabled Disabled DHCP Server Disabled Enabled Enabled Enabled Disabled Enabled (Dynamic Enabled (Dy- Enabled (Dy- Disabled NAPT) namic NAPT) namic NAPT) DNS Proxy Disabled Enabled Enabled Enabled Disabled Bridge Mode: Bridge Mode is used when there is one PC connected to the LAN-side Ethernet port.

  • Page 20: Wan Configuration

    PPP Half Bridge: Although the Router mode is capable of terminating the PPP in the modem and hence does not require PPPoE client software on the host PC, there are some disadvantages to Router mode when only single-user support is required. For in- stance, Router mode uses NAT which requires ALG support.
  • Page 21 Virtual Circuit: Select Enable to activate the current PVC configuration. The current PVC is displayed at the top of the page in parenthesis. Default is Enabled for PVC0 and Disabled for PVC1-PVC7. Bridge: Enable to connect the LAN to the WAN (bridge the two connections). This is available in Bridge Mode only (see Table 5-2).

  • Page 22: Atm

    Answer: Please go to this link http://pf.itd.nrl.navy.mil/projects.php?name=mgen. Encapsulation: The different types of encapsulation include PPPoA VC-Mux, PPPoA LLC, 1483 Bridged IP LLC, 1483 Routed IP LLC, 1483 Bridged IP VC-Mux, 1483 Routed IP VC-Mux, Classical IP over ATM, PPPoE VC-Mux, PPPoE LLC, and PPPoENone. 5.2.1 ATM VPI: Virtual Path Identifier is a virtual path used for cell routing that is identified by an eight bit field in the ATM cell header.

  • Page 23: Dhcp Client

    transmitted, the PVC loses the token it has accumulated. In the case of multiple PVCs, CBR specified PVCs will have higher priority than PVCs with UBR. For example, the CBR PVCs will take their bandwidth and the remaining bandwidth will be split among the UBR PVCs. In the case of total PVC CBR bandwidth exceeding ADSL upstream, the total upstream bandwidth will be shared proportionally to the bandwidth allo- cated for each CBR PVC.

  • Page 24: Static Ip Settings

    MAC Spoofing: Enable MAC Spoofing to make a different MAC Address appear on the WAN side. This is also used to solve the scenario where the ISP only recognizes one MAC Address. System default is Disable. MAC Address: When MAC Spoofing is enabled, copy the ISP-recognized MAC address here.

  • Page 25: Lan Configuration

    5.3 LAN Configuration The LAN configuration page allows you to set the configuration for the LAN port. LAN IP Address & Subnet Mask: The LAN IP Address is what the computer uses to identify and communicate with the Router (this is the address you enter in the address bar of Internet Explorer to access these pages).
  • Page 26 with System Allocated as the default. System Allocated: The DHCP address pool is based on LAN port IP address plus 12 IP addresses. For example, when the LAN IP address is 10.0.0.2; the DHCP ad- dress pool the range from 10.0.0.3 to 10.0.0.14. User Defined: When User Defined is selected, the DHCP address pool starts at the User Defined Start Address and ends at the User Defined End Address.

  • Page 27: Ethernet Mode Setting

    Save Configuration: Clicking this will link you to the Save Settings / Reboot page. 5.3.2 Ethernet Mode Setting The Ethernet Mode configuration page allows you to set the LAN port into the following modes: AutoSense (default): The Router will automatically sense which mode to use, se- lecting between 100 Mbps Full Duplex, 100 Mbps Half Duplex, 10 Mbps Full Duplex, and 10 Mbps Half Duplex.

  • Page 28: Ppp Configuration

    5.4 PPP Configuration The PPP Configuration page allows you to configure multiple PPP sessions for each PVC. Multiple PPP sessions enables you to set up different connection settings and be able to toggle/choose those settings for each PVC. The Router can support up to total of 16 PPP sessions, and each PVC can support up to 8 PPP sessions.

  • Page 29: Ppp Session Configuration

    PPP Account Configuration Status table will be displayed at the bottom of this page to show all the accounts. The status table does not display the password. The Number of PPP Accounts: It displays the total number of PPP Accounts entered. 5.4.2 PPP Session Configuration Once you set up a PPP Account, you can begin PPP Session configuration either by clicking the Go back to PPP Configuration link on the PPP Account Configuration...
  • Page 30 Disconnect Timeout: The Disconnect Timeout allows you to set the specific period of time, in minutes, to disconnect from the ISP. The default is 0, which means never dis- connect from the ISP. Range: 0-32767 Default: 0 PPP Idle Timer Config: It will link you to the PPP Disconnect Timer Configuration page (see Section 5.4.3).
  • Page 31 packet will be fragmented before the transmission. During the PPP negotiation, the peer of the PPP connection will indicate its MRU and will accept any value up to that size. Range: 0-32767 Default: 1492 MSS: Maximum Segment Size is the largest size of data that TCP will send in a single, unfragmented IP packet.

  • Page 32: Ppp Disconnect Timer Configuration

    5.4.3 PPP Disconnect Timer Configuration The PPP Disconnect Timer Configuration page enables you to configure what action will bring a PPP Session out of the Idle state (disconnected state) and reset the Idle Timer. This is done by specifying criteria contained in packets, namely IP Protocol and Port.
  • Page 33 Only filtered traffic will reset the Idle Timer (use filter below): Selecting this option will enable the PPP Idle Timeout filter and only allow traffic specified in the filter table to reset the idle timer. The traffic specified in the filter table must also correspond with the Filter Application selection.

  • Page 34: Ppp Miscellaneous Configuration

    Protocol #: It is the IP protocol (number) through which the PPP session can be acti- vated. The Protocol Numbers for filters are: TCP Protocol Number: 6 UDP Protocol Number: 17 ICMP Protocol Number: 1 IGMP Protocol Number: 2 Port #: It is the Port through which the PPP session can be activated. The default filters are: HTTP TCP Port: 80 FTP TCP Port: 20 and 21...

  • Page 35: Nat Configuration

    If the PPP session is disconnected after the Disconnect Timeout, how can I re- connect it? Answer: You have to go to the PPP Status page, enter the correct connection number, select the Connect option in the dropdown menu, and then click Execute. This will restart the PPP secession.
  • Page 36 figuration between multiple LAN clients and multiple WAN connections. When Dynamic NAPT is chosen (default), there is no need to configure the NAT Session and NAT Session Name Configuration. Session Name: It allows you to enter a Session Name to help distinguish different NAT Sessions for different interfaces among different PPP sessions and PVCs.
  • Page 37 NAT: Use this field to Enable/Disable NAT. Default is Enable. Mode: Options for the NAT dropdown menu are: NAT: Static peer-to-peer mode (1x1). NAPT: Static multiple mapping mode (1xN). Dynamic NAPT (default): Dynamic multiple mapping mode (NxN). Session Name: It allows you to select the session from the configured NAT Session Name Configuration.

  • Page 38: Virtual Server Configuration

    5.6 Virtual Server Configuration The Virtual Server Configuration page allows you to set the configuration of the Virtual Server. Virtual Servers are used for port forwarding from the WAN to LAN networks. All UDP/TCP ports are protected from intrusion. If any specific local PCs need to be mapped to the UDP/TCP port on WAN side, please input the mappings here.

  • Page 39: Bridge Filtering

    server. 5.7 Bridge Filtering Bridge Filtering allows packets to be forwarded or blocked, depending on the MAC ad- dress. The Bridge Filtering configuration page allows you to set the configuration of MAC filtering. There can be up to 4 different Bridge Filtering configurations. Source MAC: This is the Source MAC to block or from which to forward.

  • Page 40: Dns Configuration

    to the Destination MAC. How do I block packets from MAC address 000002fa6fab through IP protocol? Answer: First go to the Bridge Filtering page under Configuration. Then type 000002fa6fab in the ID Source MAC field and 0800 in the Type field. If bridge filtering is not already enabled, select Yes under the Enable Bridge Filtering field.
  • Page 41 messages will be directly sent to the DNS servers. DNS Proxy is enabled by default. Auto Discovered: When enabled (default), the DNS proxy will store the DNS server IP addresses obtained from DHCP client or PPP into the table. All DNS query messages will be sent to the dynamically obtained DNS server.

  • Page 42: User Password Configuration

    Host IP (Add Only): It is the IP address of the DNS Server. DNS Proxy Setting: It is a table of all DNS server IP addresses. DNS Server Setting: It is a table of all DNS sever URL names. Save Configuration: Clicking this will link the user to the Save Settings / Reboot page. 5.9 User Password Configuration The User Password Configuration page allows the user or admin to set the password for the user account.
  • Page 43 Save & Reboot: Click this to apply all changes. Reboot Only: Do this to discard all changes since last save. After either one of these buttons are clicked, the Router will do the following: Save & Reboot: Two pages will appear after pressing this button. The first one states: “Your settings are being saved and the modem being rebooted.

  • Page 44: Admin Privilege

    6. Admin Privilege The links under Admin Privilege are only accessible when user is logged in as Admin. Regular user account does not have authorization to view or alter the content on the pages in the Admin Privilege section. 6.1 WAN Status The WAN Status page shows the information and status of WAN PVCs.

  • Page 45: Adsl Configuration

    Reset Counters: This button allows user to reset the ATM Status counter. 6.3 ADSL Configuration The ADSL Configuration page allows you to set the configuration for ADSL protocols.

  • Page 46: Route Table

    Annex Mode Config: It allows you to manually configure the Router for Annex A or Annex B mode by selecting User Configured and choosing the Annex Mode in the next field. User Selected Annex Mode: It allows you to select from Annex A and Annex B. Please DO NOT change the default setting of Annex Mode unless you are instructed to do this by your ISP.
  • Page 47 The Gateway field of the static route entry allows users to either enter a Gateway IP address or select a Network Interface. All user-defined routes retained in the CPE memory, regardless if they are already in the Routing Table, are displayed on the same Route Table page. All user defined route entries kept in the CPE memory during run time are saved to flash when the user chooses to save and reboot the CPE.

  • Page 48: System Default Gateway Configuration

    Gateway associated with the selected Network Interface, then that Gateway’s IP address appears in the Gateway field of the route entry. If the selected Network Interface is dynamic but the connection is not established, then the route entry does not appear in the Routing Table. When the interface comes up later, the route entry is then added.

  • Page 49: Learned Mac Table

    6.5 Learned MAC Table Network bridges operate at the physical network layer. The purpose of a bridge is to connect two or more networks and enable packet sharing between them. Bridges are different from routers because they forward packets based on physical addresses, whereas routers use IP address to forward packets.
  • Page 50 configuration of RIP. The actual RIP configuration is in the RIP Per Interface Configu- ration. RIP: It allows you to Enable or Disable the RIP session. The resulting RIP session will monitor all network interfaces that are currently available for messages from other RIP routers.

  • Page 51: Rip Per Interface Configuration

    Range: 0 - 2147483647 Default: 180 Garbage Timeout: It allows you to enter the Garbage timer in seconds. This timer specifies how long the expired and invalidated routes are kept in the Internal RIP Route Table before they are removed from it. Range: 0 - 2147483647 Default: 120 6.6.1 RIP Per Interface Configuration...

  • Page 52: Miscellaneous Configuration

    V2 BC: The supplier transmits in RIPv2 Broadcast. V2 MC: The supplier transmits in RIPv2 Multicast. Listener: It allows you to select the Listener Mode (RIP Receive). V1: The listener receives the RIPv1 only. V2: The listener receives the RIPv2 only. V1+V2: This listener receives the both RIPv1 and RIPv2.
  • Page 54 HTTP Server Access: It allows you to configure where these Web pages could be ac- cessed from. All (default): When this field is checked, it allows both WAN and LAN access to the Web pages. Restricted LAN: It allows the Web pages access from LAN side. Restricted WAN Specified IP &...
  • Page 55 disable the NAT to run on router mode only, disable the DHCP server on the LAN port, and make sure the routing table has the correct routing entry. DHCP Relay Target IP: If DHCP Relay is enabled, DHCP requests are relayed to DHCP Target IP on the WAN side.

  • Page 56: Tcp Status

    6.8 TCP Status The TCP Status page shows the statistics for all TCP connections. This page contains information that is dynamic and will refresh every 2 seconds.

  • Page 57: Admin Password Configuration

    6.9 Admin Password Configuration The Admin Password Configuration page allows you to set the password for administra- tor. The Admin password can be up to 65 characters (excluding ‘&’). 6.10 Reset to Factory Default The Reset to Factory Default page allows you to reset the Router to original factory default configuration.

  • Page 59: Diagnostic Test

    6.11 Diagnostic Test The Diagnostic Test page shows the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides. This page will continually refresh every 2 seconds until all tests are complete. 6.12 System Log The System Log page shows the events triggered by the system.

  • Page 60: Local Code Image Update

    6.13 Local Code Image Update The Local Code Image Update page allows you to upgrade the image code locally. Firstly, you need to download the new code to your local drive. And then follow the de- scription below to update your firmware. Click Code Image Update to proceed Click Image Download to load the file.
  • Page 61 Please wait while system is preparing Browse the location of file, firmware.dlf for download. It will take several sec- file, and click the Upload to start the onds. Once you enter this page, the update. The Router will reboot as part ADSL LED will extinguish till you com- of the process of updating code.

  • Page 62: Appendix A. Compliance Statement

    Appendix A. Compliance Statement FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

  • Page 63: Appendix B. Encapsulation Mode

    Appendix B. Encapsulation Mode Bridged mode（RFC-1483） RFC-1483 provides the simplest method of connecting end station over an ATM network. User data in the form of Ethernet frames is encapsulated into AAL5-PDU for transport over ATM. RFC-1483 provides no authentication and configuration such as would be provided by PPP.

  • Page 64: Appendix C. Troubleshooting

    Overview This chapter covers some common problems that may be encountered while using ADE-3110 and some possible solutions to them. If you follow the suggested steps and ADE-3110 still does not function properly, contact your dealer for further advice. General Problems Question 1 Can't connect to ADE-3110 to configure it.
  • Page 65 If ADE-3110 is configured correctly, contact your ISP to see if Internet connection is working correctly. Question 2 If the PPP is disconnected after the Disconnect Timeout and how can I reconnect it? Answer 2 You have to go to the PPP link under Status column, choose the correct PVC and Connect option, and then click Execute to restart a new PPP secession.

  • Page 66: Appendix D. Specifications

    Appendix D. Specifications ADE-3110A/ADE-3110B Product ADSL Modem Router Model ADE-3110A ADE-3110B ADSL Standards Annex A Annex B Full-rate ANSI T1.413 issue 2 and ITU-T G992.1 (G.DMT), Splitter- less ITU-T G.992.2 (G.lite) Protocol Support RFC2364 - PPP over ATM (LLC/VCMUX) RFC2516 - PPP over Ethernet (LLCSNAP/VCMUX) RFC1577 - Classic IP over ATM RFC1483 - Bridged IP over ATM(LLCSNAP/VCMUX) RFC1483 - Routed IP over ATM (LLCSNAP/VCMUX)

Table of Contents