1. Manuals
  2. Brands
  3. Planet Manuals
  4. Network Router
  5. ADSL 2/2+ Router with USB Port ADE-3410v2
  6. User manual

Planet ADSL 2/2+ Router with USB Port ADE-3410v2 User Manual

Adsl 2/2+ router with usb port
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ADSL 2/2+ Router with USB
Port
ADE-3410v2
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for Planet ADSL 2/2+ Router with USB Port ADE-3410v2

Summary of Contents for Planet ADSL 2/2+ Router with USB Port ADE-3410v2

  • Page 1 ADSL 2/2+ Router with USB Port ADE-3410v2 User's Manual...
  • Page 2 Copyright Copyright© 2007 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
  • Page 3 R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE) The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.

  • Page 4: Table Of Contents

    Table of Contents 1. Introduction... 6 1.1 Features... 6 1.2 Package Contents ... 7 1.3 Physical Details ... 7 2. Installation... 9 2.1 System Requirement ... 9 2.2 Hardware Installation ... 10 2.3 Router Parameters Setting ... 11 2.4 Factory Reset Button ... 12 2.5 USB Installation ...
  • Page 5 3.5.2 LAN... 36 3.5.3 NAT... 37 3.5.4 Security... 41 3.5.5 Routing ... 43 3.5.6 DNS ... 45 3.5.7 DSL ... 46 3.6 Diagnostics ... 47 3.7 Management ... 47 3.7.1 Settings ... 47 3.7.2 System Log... 49 3.7.3 Internet Time ... 50 3.7.4 Access Control ...

  • Page 6: Introduction

    1. Introduction The PLANET ADSL 2/2+ Router, ADE-3410v2, provides office and residential users the ideal solution for sharing a high-speed ADSL 2/2+ broadband Internet connection on one Ethernet port and one USB port. It can support downstream transmission rates of up to 24Mbps and upstream transmission rates of up to 3.5Mbps.

  • Page 7: Package Contents

    VPN Pass through Support PCs with VPN (Virtual Private Networking) software using PPTP, L2TP, and IPSec are transparently supported - no configuration is required. RIP Routing It supports RIP routing protocol for routing capability. Simple Network Management Protocol (SNMP) It is an easy way to remotely manage the router via SNMP.
  • Page 8 LED Indicator Meaning Lit when power is ON. Link Lit when DSL line is connected. Blink when DSL line is training. Data Blink when DSL data is transferring. Lit when connected to an Ethernet device. Blink when data is Transmitted / Received. Lit when the USB port is connected to the PC and working properly.

  • Page 9: Installation

    Rear panel Port and Button Definition Port Meaning Power Power ON/OFF switch Switch Power Connect the supplied power adapter to this jack (10 DC, 1A). After the device is powered on, press it to reset the device or restore to factory default settings. Reset the device 6 seconds above to Reset restore the factory default settings (this is used when you can not login to the router, e.g.

  • Page 10: Hardware Installation

    3. 64 MB RAM minimum 4. 20 MB of free disk space minimum 5. Ethernet Network Interface Card 2.2 Hardware Installation This section describes how to connect and configure the ADE-3410v2. The DSL router may connect to a PC’s USB or Ethernet. DSL router will support at least one of connectivity methods.

  • Page 11: Router Parameters Setting

    USB Installation To connect the DSL router to the PC’s USB port, perform the following: Connect the USB cable to the USB port on the DSL router. The cable has two different connectors; you may have to try both connectors. Connect the other end of the USB cable into the PC’s USB port.

  • Page 12: Factory Reset Button

    2.4 Factory Reset Button The Router may be reset to the original factory default settings by depressing the reset button for a few seconds while the device is powered on. Use a ballpoint or paperclip to gently push down the reset button. Remember that this will wipe out any settings stored in flash memory including user account information and LAN IP settings.
  • Page 13 the windows will search CD-Rom for the best USB driver. The dialog prompted you to choose your search and installation options. You can choose the path of USB drive installation. Click <Next > The dialog prompted Please wait while the wizard searches, when the USB driver has be searched by the Windows, Click <Next >...

  • Page 14: Introduction To Web Configuration

    Click the button<Finish> to complete the USB driver installation. 3. Introduction to WEB Configuration 3.1 Quick Setup The Quick Setup allows the user to configure the ADSL router for DSL connectivity and Internet access. It also guides the user though the WAN network setup first and then the LAN interface setup.

  • Page 15: Quick Setup

    ADE-3410V2 also supports pass-through PPPoE sessions from the LAN side while simultaneously running a PPPoE client fro non-PPPoE LAN devices. NAPT and firewall are always enabled when PPPoE mode is selected, but they can be enabled or disabled by the user when MER or IPoA is selected, NAPT and firewall are always disabled when Bridge mode is selected.
  • Page 16 STEP 4: Click Next to display the following screen. Choosing different connection types pops up different settings requests. Enter appropriate settings that are requested by your service provider. The following descriptions state each connection type setup separately. For example, PPP over ATM (PPPoA) and PPP over Ethernet (PPPoE) 1.
  • Page 17 using the LAN interface IP address. The ADSL router extends the IP subnet at the remote service provider to the LAN PC. That is, the PC becomes a host belonging to the same IP subnet. The ADSL router bridges the IP packets between WAN and LAN ports, unless the packet is addressed to the router’s LAN IP address.

  • Page 18: Preparations Before Login Router

    5. After clicking Save/Reboot, the router will save the configuration to the flash memory, and reboot. The Web UI will not respond until the system is brought up again. After the system is up, the Web UI will refresh to the Device Info page automatically. The ADE-3410v2 is ready for operation and the LEDs display as described in the LED description tables.

  • Page 19: System Status

    After logging in the ROUTER by a super username, you can query, configure, and modify all configurations of the ROUTER; and you can diagnose the ROUTER system too. You need to reboot the ROUTER to enable your modification or configuration effective sometimes, e.g.

  • Page 20: Wan

    This interface contains the following information: Board ID: Software Version: Bootloader (CFE) Version: Upstream Line Rate/Downstream Line Rate LAN IP Address: The management IP address Default Gateway: No gateway in a pure bridging mode; under other modes such as PPPOE/PPPOA, it is the address of the uplink equipment. DNS Server address: Obtained from the uplink equipment in PPPOE/PPPOA mode;...

  • Page 21: Statistics -- Lan

    3.4.3 Statistics -- LAN Click “Statistics”-->”LAN” to show the following interface. You can query information on packets received at the Ethernet, USB and Wireless interfaces. Click “Reset Statistics” to return the values to zero and recount them. 3.4.4 Statistics -- WAN Click “Statistics”-->”WAN”...

  • Page 22: Statistics -- Atm

    3.4.5 Statistics -- ATM Click “Statistics”-->”ATM” to show the following interface. You can query information on packets received at the ATM interfaces. Click “Reset” to return the values to zero and recount them. 3.4.6 Statistics -- ADSL Click “Statistics”-->”ADSL” to show the following interface. If the DSL line is activated, the following window will show.

  • Page 23: Route

    You will see the following information pertinent to the ADSL line in the page: Mode: G.DMT/G.LITE/T1.413/ADSL 2+/ADSL 2/READSL2 Line Coding: Trallis on, etc. Status: Link Down, No Defect, Training Link Power State: L0, L1, L2 Rate (Kbps): Upstream Line Rate/Downstream Line Rate. At the lower part of this interface, there is a “Reset Statistics”...

  • Page 24: Arp

    3.4.8 ARP Click “ARP” to show the following interface. You can query the MAC and IP addresses information of the equipment attached to the ROUTER. 3.4.9 DHCP Click “DHCP” to show the following interface. You can query the IP addresses assignment from the DHCP server.

  • Page 25: Advanced Setup

    3.5 Advanced Setup Click “Advanced Setup” to enter the advanced system setup interface. By default, there are two options at the left side of the interface: “WAN”, “LAN”, etc. See the following interface. If the ROUTER is configured to a routing mode, such as built-in PPPOE access, there will be more options at the left: “LAN”, “WAN”, “NAT”, “Security”, “Routing”, “DNS”, “DSL”...

  • Page 26: Configure Pppoe

    Choose Add, Edit, or Remove to configure WAN interfaces. Choose Save/Reboot to apply the changes and reboot the system. Now we only show you how to add PVC. 3.5.1.1 Configure PPPoE Click “Add” to add a certain piece of PVC. The following descriptions are given by an example of adding “PVC 8/35”...
  • Page 27 PPP Username: the correct user name that your ISP has provided to you. PPP Password: the correct password that your ISP has provided to you. PPPoE Service Name: If your ISP provided it to you, please input it. Unless don’t input anything. Authentication Method: AUTO, PAP, CHAP, MSCHAP.
  • Page 28 Multicast, WAN Service. IGMP Multicast: IGMP proxy. For example, if you need PPPoE mode support IPTV, please enable it. WAN Service: Please enable it, unless you don’t need to active the PVC. Click “Next” to show the following interface. In this interface, it shows the all configuration. You can see some default values: NAT enable, Firewall enable.

  • Page 29: Configure Pppoa

    modifications. NOTE: You need to reboot to activate this WAN interface and further configure services over this interface. 3.5.1.2 Configure PPPoA Click “Add” to add a certain piece of PVC. The following descriptions are given by an example of adding “PVC 8/35” (PPPOA mode). Click “Add”...
  • Page 30 Click “Next”. In this interface, you can modify the PPP Username, PPP Password, Authentication Method and so on. PPP Username: the correct user name that your ISP has provided to you. PPP Password: the correct password that your ISP has provided to you. Authentication Method: AUTO, PAP, CHAP, MSCHAP.

  • Page 31: Configure Mer

    In this interface, you can modify the Service name and enable/disable the IGMP Multicast, WAN Service. IGMP Multicast: IGMP proxy. For example, if you need PPPoA mode support IPTV, please enable it. WAN Service: Please enable it, unless you don’t need to active the PVC. Click “Next”.
  • Page 32 Click “Next”. In this interface, you can modify the WAN IP address, Default Gateway and DNS Server settings. Obtain an IP address automatically: The ROUTER will obtain a (WAN) IP address automatically and at this time it will enable DHCP Client functions. The WAN IP address is obtained from the uplink equipment like BAS and the uplink equipment is required to enable the DHCP Server functions.

  • Page 33: Configure Ipoa

    After correctly modifications, click “Next” to show the following interface. In this interface, you can modify the Service name and enable/disable the NAT, Firewall, IGMP Multicast, WAN Service. Enable NAT: Select it to enable the NAT functions of the ROUTER. If you are not to enable NAT and intend the user of the ROUTER to access the Internet normally, you must add a route on the uplink equipment;...
  • Page 34 Click “Next”. In this interface, you can modify the WAN IP, Default Gateway and DNS Server settings. WAN IP Address: Input the IP address of the WAN interface provided by your ISP. WAN Subnet Mask: Input the subnet mask concerned to the IP address of the WAN interface provided by your ISP.
  • Page 35 IGMP Multicast, WAN Service. Enable NAT: Select it to enable the NAT functions of the ROUTER. If you are not to enable NAT and intend the user of the ROUTER to access the Internet normally, you must add a route on the uplink equipment; otherwise the access to the Internet will fail.

  • Page 36: Lan

    Click “Next”. In this interface, you can modify the Service name. WAN Service: Please enable it, unless you don’t need to active the PVC. Click “Next”. In this interface, it shows the all configuration. Click “Save” to save these settings. And you can click “Back” to make any modifications.

  • Page 37: Nat

    Enable IGMP Snooping: It used to Bridge mode. 3.5.3 NAT Click “NAT” to show the following interface. Under “NAT”, there are four network share modes: “virtual Server”, “port triggering”, and “DMZ Host”. 3.5.3.1 NAT -- Virtual Servers Setup In this interface, you can query any preset virtual server, delete an exiting virtual server, and add a new virtual server.
  • Page 38 When NAT is enabled on the ROUTER, the whole LAN that the ROUTER is attached will appear as a single machine on the Internet. Normally, external users are not allowed to visit the PCs in the whole LAN to which the ROUTER is attached. But under some circumstances, we hope that some PCs will be open and allow anyone to access them.
  • Page 39 Service Name: Select one service item, such as Mail (SMTP), Mail (POP3), Web Server (HTTP), FTP Server, and TFTP, from the list. The information about the selected item will appear in the box below. Customized server: Enter a new service name to establish a specified user service category.
  • Page 40 A maximum 32 entries can be configured. 3.5.3.3 NAT -- DMZ Host Click “DMZ Host” to pop up an interface as below. In this interface, you can configure DMZ services. Demilitarized Zone (DMZ) is a technology that enables the ROUTER to forward all input packets onto a server specified internally.

  • Page 41: Security

    3.5.4 Security Click “Security” -->” IP Filtering” to show the following interface. By default, the firewall is enabled. The firewall is used to block document transmissions between the Internet and your PC. It serves as a safety guard and only permits authorized documents to be sent into the LAN.

  • Page 42: Incoming Ip Filtering Setup

    3.5.4.2 Incoming IP Filtering Setup Click “Security”-->” IP Filtering”-->” Incoming” to show the following interface. By default, all incoming IP traffic from the WAN is blocked when the firewall is enabled. However, some IP traffic can be ACCEPTED by setting up filters. The screen allows you to create a filter rule to identify incoming IP traffic by specifying a new filter name and at least one condition below.

  • Page 43: Routing

    3.5.4.3 Parental Control Click “Security”-->”Parental Control” to show the following interface. Click “add” to show the interface. This page adds time of day restriction to a special LAN device connected to the Router. The 'Browser's MAC Address' automatically displays the MAC address of the LAN device where the browser is running.
  • Page 44 Click “ENABLE Automatic Assigned Default Gateway” box to show the interface. 3.5.5.2 Routing – Static Route In this interface, you can modify the Static Route settings. Click “Static Route” to pop up an interface as shown in Fig. 3.5-47. In this interface, you can query the preset static routes, delete an existing static route, or add a new static route.

  • Page 45: Dns

    3.5.6 DNS 3.5.6.1 DNS Server In this interface, you can modify the DNS server settings. If 'Enable Automatic Assigned DNS' checkbox is selected, this router will accept the first received DNS assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s) during the connection establishment.

  • Page 46: Dsl

    Click “Add” to add dynamic DDNS. 3.5.7 DSL In this interface, you can modify the DSL settings. Select one you need. But the default setting check G.dmt / G.lite / T1.413 / ADSL2 / ADSL2+ / Bitswap / SRA. The ROUTER will negotiate the modulation mode with the DSLAM.

  • Page 47: Diagnostics

    3.6 Diagnostics Click “Diagnostics” to show the interface. Your router is capable of testing your DSL connection. The individual tests are listed below. If a test displays a fail status, click "Rerun Diagnostic Tests" at the bottom of this page to make sure the fail status is consistent. If the test continues to fail, click "Help" and follow the troubleshooting procedures.
  • Page 48 3.7.1.2 Settings Update Click the “Browsing...” button, select the correct update configure settings file. Then click the “Update Settings” to update the Router settings. 3.7.1.3 Settings Restore Default...

  • Page 49: System Log

    Click “Restore Default Settings” to restore DSL router settings to the factory defaults. 3.7.2 System Log Click “System Log” to show the following interface. The system log dialog allows you to view the system log and configure the system log options. Click “Configure System Log”...

  • Page 50: Internet Time

    If you select “Remote” or “Both”, all events will be transmitted to the specified UDP port of the specified log server. After operations under “Configure System Log”, click “View System Log” to query the system logs. In this example, the “View System Log” is a system default one.
  • Page 51 you can enable/disable the HTTP, ICMP, SNMP, TELNET and TFTP services. And the LAN side and WAN side can have different configurations. 3.7.4.2 Access Control -- IP Addresses Click “Access Control”-->”IP Addresses” to show the following interface. If enabled, permits access to local management services from IP addresses contained in the Access Control List.

  • Page 52: Update Software

    management station permitted to access the local management services, and click “Save/Apply”. 3.7.4.3 Access Control – Passwords Click “Access Control”-->”Passwords” to show the following interface. In the interface, you can modify the accounts passwords. 3.7.5 Update Software Click “Update Firmware” to show the following interface. In this interface, you can update the ROUTER Firmware.

  • Page 53: Save/Reboot

    before the reboot is over. You must guarantee the update software is right and accurate. It is strictly forbidden to use other software for updates. After update software, it is suggested to restore the ROUTER to the factory defaults and configure it again. 3.7.6 Save/Reboot Click “Save/Reboot”...
  • Page 54 Descriptions In this example, the ROUTER is connected to the DSLAM through PVC 8/35 and the access mode is the built-in PPPOA+NAT. The encapsulation of the BRAS downlink port is PPP OVER ATM, the authentication is AUTO, the IP address is 10.28.106.200, the IP Pool is 10.28.106.*, and the IP address of uplink port is 10.61.92.157.

  • Page 55: Ppp Over Ethernet (Pppoe) Mode

    You can also modify the PVC 8/35. If you need to modify the LAN IP address and DHCP server information, you can do it in “LAN” in “Advanced Setup”. After the dial-up is successful, the IP address that the ROUTER obtains at the WAN-side port ppp_8_35_1.

  • Page 56: Mer+Dhcp Mode

    3. In the “ATM PVC Configuration” interface configure VPI/VCI as 8/35 and then click “Next”. 4. In the “Connection Type” interface, select “PPP over Ethernet (PPPoE)” and “LLC/SNAP-BRIDGING” as the encapsulation, and then click “Next”. 5. In the “PPP User name and Password” interface, enter the user name and password provided by your ISP.
  • Page 57 address of the ROUTER is automatically obtained through DHCP; the PC attached to the ROUTER is assigned with a private IP address (within the same segment as the management IP address 192.168.1.1); the NAT functions of the ROUTER is enabled, and the private address of the PC is translated into the public address 10.28.108.* (2~254) dynamically assigned by BRAS for accessing the ISP.

  • Page 58: Ip Over Atm (Ipoa) +Nat Mode

    If “Enable NAT” is disabled during the configuration, you must configure the route on the BRAS; otherwise you cannot access your ISP. In applications, “Enable NAT” must be checked. 4.4 IP over ATM (IPoA) +NAT Mode Descriptions In this example, the ROUTER is connected to the DSLAM through PVC 8/35 and the access mode is the IPOA+NAT.

  • Page 59: Leased Line Mode

    “LLC/SNAP-ROUTING” as the encapsulation, and then click “Next”. 5. In the “WAN Settings” interface, input the IP address, subnet mask, and DNS server address provided by your ISP. Don’t select “Use the following default gateway”. And then click “Next”. WAN IP Address: 20.1.1.2 WAN Subnet Mask: 255.255.255.0 Primary DNS server: 168.95.1.1 Secondary DNS server: 168.95.192.1...

  • Page 60: Ppp Over Ethernet (Pppoe) Ip Extension Mode

    10.28.108.1. Setting 1. Activate your browser and input “192.168.1.1” in the address column to login the ROUTER. 2. Click “Advanced Setup” -> “WAN”, then click “add”. 3. In the “ATM PVC Configuration” interface configure VPI/VCI as 8/35 and then click “Next”. 4.

  • Page 61: Questions & Answers

    by BRAS through its built-in PPPOE dial-up. The ROUTER will assign this public IP address to the PC (configured as “Obtain an IP address automatically”) attached to it in the DHCP mode. At this time, NAT will have no effect. From the point view of the user, the ROUTER seems working in the “Briding”...
  • Page 62 2. Question: Why LINK/ACT LED is not lighting? Answer: • Check the connection between the ADSL router and your computer or Hub/Switch. • Check your PC or Hub/Switch running status and make sure them are working normally. • Check your network cable for connecting the Router with other device: For PC, you should use the crossover cable;...

Table of Contents