Audio Recording; Selecting The Audio Input Signals; Adjusting The Audio Recording Level; Monitoring The Sound During Recording - Panasonic DVCPRO AJ-D410AP Operating Instructions Manual

Audio recording

Selecting the audio input signals

1
Select the desired input signals using the
AUDIO IN switch.
To use the front microphone i Select FRONT (MIC).
To use the rear microphone i Select REAR (MIC).
To use the audio products
<Note>
≥When the front microphone has been selected, select ON as the
<FRONT MIC POWER> setting for the MIC/AUDIO sub-menu
item if the phantom mic (+48 V) needs to be supported. (See page
36)
≥ Set the rear mic power switches to ON if the phantom mic (+48V)
must be supported when the external microphones are selected.
≥ When the wireless receiver is to be used, set the AUDIO IN
switch on the side panel to REAR (MIC or LINE), and select
WIRELESS as the REAR SEL CH1 and REAR SEL CH2 settings
for the <MIC/AUDIO> submenu item.

Adjusting the audio recording level

When the AUTO SELECT CH1/CH2 selector switch is set to AUTO,
the input levels of the CH1 and CH2 sound are automatically
adjusted.
To adjust the input levels of the CH1 and CH2 sound manually,
proceed as follows:
1
Set the AUTO SELECT CH1/CH2 selector
switch to MAN.
2
While monitoring the audio level meter
displayed inside the viewfinder, adjust the
AUDIO LEVEL CH1 and CH2 knobs in such
way that the maximum input level will not
reach or exceed "- - - - - + - - - - + ".
<Notes>
≥ The level meter values shown in the figure on the right serve as a
rough guideline.
≥ When the unit is used in the MAN mode, the LIMITER CH1 and
LIMITER CH2 settings (see page 36) for the <MIC/AUDIO>
submenu item become operational.
Monitoring the sound during
recording
The audio input signals can be monitored through the monitor
speaker or earphone. When the PHONES jack is used, no sound
will be heard through the monitor speaker.
The volume of the monitored sound can be adjusted using the
MONITOR control.
<Note>
Howl may be caused if the volume of the audio monitor speaker is
too high. In a this situation, rotate the audio monitor level control to
a lower level which does not give rise to howl.
i Select REAR (LINE).
Monitor
speaker
QUICK FOCUS
1
FILTER
MODE CHECK
1 3200K
5600K
2
+1/8ND
3 5600K
5600K AUTO IRIS MODE
4
+1/64ND
SCENE FILE
BACK.L
USER
STD
F1
SPOT.L
F2
MONITOR
FULL
AUTO F3
F4
STD
VTR GAIN OUTPUT WHITE BAL
JOG dial button MONITOR control
EX TAPE NEAR END FLUO.
iREC TCG 12:34:56:00
¢1¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢
¢2¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢
SPOT QUICK FOCUS
1100 LOW LIGHT
/
DS e p -01-01 23:59:00
=========
C H 1
C H 2
CH1
CH2
–40 –36 –32 –28 –24 –20 –16 –12 –8 –4 0dB
29
AUDIO LEVEL AUDIO LEVEL
CH1 control CH2 control
POWER/
WARNING
AUDIO LEVEL AUDIO
SELECT
CH 1 CH 2
switch
RESET
TCG AUDIO SELECT
COUNTER
F-RUN
AUDIO
SET
TC
MAN
LITHIUM BATT UB R-RUN
SEE MANUAL AUDIO IN
CH 1 CH 2
REAR MIC POWER AUDIO IN
FRONT MIC
ON
MIC
REAR
OFF
LINE
switch
CH 1 CH 2 CH 1 CH 2
PHONES
jack
Rear mic power
switches
AWB+02
Z78
32K
.
ATW
F56
.
0d B
FL1
min 1 3 . 4V
¢¢¢
The reference value