Advertisement
3-WIRESERVICECORD OR CONDUIT
4-WIRESERVICECORDOR CONDUIT
INSTALLATION
INSTALLATION
1. Insure that the copper ground strap IS CONNECTED
(MOBILE HOMES OR AS REQUIRED BY CODES)
between the middle post of the main terminal
1. The copper ground strap connected between the
connection block and the range chassis,
neutral (middle) post of the main terminal block and the
chassis MUST be cut off as shown in figure 9. Save the
2. The middle wire of the service cord or ground lead of
green ground screw to attach the ground from the 4
3-wire conduit MUST connect to the neutral (middle)
wire cord. Only a 4 wire cord or conduit should be
post of the main terminal block. The other two wires of
used.
the service cord or conduit connect to the outside
posts of the main terminal connection block. Polarity is
2. The ground wire from the service cord or conduit must
unimportant,
connect to the range chassis using the green ground
screw.
3. A appropriatestrain relief for service cordor conduit
3. The white wire of the service cordor conduitmust
must be attached to the conduitplate,
connectto the neutral (middle)post of the main
terminal block.The othertwo wires of the servicecord
RED
MAIN TERMINAL
WHITE--_-'_
/
CONNECTIONEILOCK
orconduJt
connect
to the
red
and
black
posts
of the
BLACK
MIDDLE W_RE 0r
main terminal block, respectively.
SERVICE
CORD OR
GROUND
LEAD
4. An appropriate strain relief for service cord or conduit
oFCONDU,T
must be attached to the conduit plate.
GROO.0
s
CONVERSION FROM3-WIRETO 4-WIRE
tRA_,
figure 9 to connect the 4-wire service cord.
(CONNECTED
_ACTO.Y>
_--- CONDU,
T
SERVICE
PLATE
• _'0_jl '1,,,--" STAMPED (Model With 3-Wire Service Cord Attached)
_"
,_;,"r,J/"
CONDO_
T
Disconnect range from power. Remove the access cover
STRA_N -
ReLJF
,_",_
!j_]
on back of range and removethe 3-wire service cord from
the main terminal block. Followinstructionsas outlinedin
NOTE: Cord replacement- ONLY a power supplycord
/
Y
_
FOR USE w_
rated at 240 volts minimum,40 amperes or 50 amperes
REMOVE BRA
STAMPED
CORD
& RE-ATTAC
power
supply
cord
that
is marked
for use
with
nominal
MARKED "CO
1 318"(34.93 mm) diameter connection opening, with
FIGURE 8
DOWN.
closed loop terminals and marked for use with ranges
ACCEPTABLE 3-WIRE PLUG INSTALLATION
shall be used.
THiS
PORTION
OF----_
/
/
_,_'_
-'I
_.
GROUND I NC STRAP
_
/
_FA_
_r'_,.j/
\
MUST BE REMOVED.
_
--. _"-_1
k, -
_,
WHITE
f
X
/-MAIN
TERMINAL
S
_'_h
_
1
BLACK
\
"_.-_.I CONNECTION
BLOCK
_
"_ /_'-,.
\
/
'f__._-_W.,TE W_R_ OF -_
X
I1_/---_ I///I
I
LI"F]'I-_'_
.,_,,_"TT]
SERVICE
CORD
X
I_ (
///
I
/
_'_\ _J )} ,I))
ORCONDUIT
_,r"__
\\
/////
//
,
GROUNO
/..-Jill
r"
.....
.'_'_'.,_,'f.
, I /
CONDUIT
\_{'YI,_
of'.u
.o.°
I;I;'#- v_ L
I ;c"_
OBE W,TH
CONOU,T,
i/^o
____j/
REMOVE BRACKET,
FLIP
Y%..,t
'_,,,
--..A_"
& RE-ATTACH
WITH
HOLE
_"_>
_
MARKED
"CONDUIT"
STAMPED _
V
DOWN.
CORD
FIGURE 9
ACCEPTABLE 4-WIRE PLUG INSTALLATION
-8-
Advertisement
