Download
Share
Print this page
Shindaiwa 89282 Conversion Instructions
  1. Manuals
  2. Brands
  3. Shindaiwa Manuals
  4. Trimmer
  5. 89282
  6. Conversion instructions
Shindaiwa 89282 Conversion Instructions

Shindaiwa 89282 Conversion Instructions

Grass trimmer to blade conversion for trimmer t282
Hide thumbs

Advertisement

Quick Links

Download this manual
X7672820101
08/10
SHINDAIWA GRASS TRIMMER TO BLADE CONVERSION
INSTRUCTIONS
Model 89282 For Trimmer T282
WARNING!
Minimize the risk of injury to yourself and others! Read the Owner's/Opera-
tor's manual originally supplied with the unit that is being upgraded and
familiarize yourself with the contents. Always wear eye and hearing protec-
tion when operating your unit.

Advertisement

loading

Related Manuals for Shindaiwa 89282

Summary of Contents for Shindaiwa 89282

  • Page 1 SHINDAIWA GRASS TRIMMER TO BLADE CONVERSION INSTRUCTIONS Model 89282 For Trimmer T282 WARNING! Minimize the risk of injury to yourself and others! Read the Owner's/Opera- tor's manual originally supplied with the unit that is being upgraded and familiarize yourself with the contents. Always wear eye and hearing protec- tion when operating your unit.

  • Page 2: Table Of Contents

    The instructions described in this manual are intended to help Always wear a harness when operating this unit you get the most from your Shindaiwa power tool as well as with a blade. A harness to protect you and others from harm. These procedures are is also recommended when using trimmer line.

  • Page 3: General Safety Instructions

    Safety Labels IMPORTANT! Safety and Operation Information Labels: Make sure all information labels are undamaged and readable. Immediately replace damaged or missing information labels. A new label is provided in this kit and additional labels are available from your local authorized Shin- daiwa dealer.

  • Page 4: Assembly

    Assembly Removing the Existing Cutting Attachment Shield 1. Remove the four socket-head cap screws (A), bracket (B) and two shims (C). 2. Remove the cutting attachment shield from the gearcase. Remove Gear Case 1. Remove gear case locating screw (D) and loosen gear case clamp (E).
  • Page 5 Install Hanger 1. Slide hanger (A) onto outer tube & position as shown. Attach with 5x12 socket head cap screw, but do not tighten at this time. Handle Install Handle and Barrier Bar 1. Install handle and barrier. Install Gear Case 1.
  • Page 6 Install New Cutting Attachment Shield Assemble the Cutting Attachment Shield to the Outer Tube. 1. Insert the cutting attachment shield (A) between the outer tube and the cutting attachment mounting plate (B). 2. Fit the two shims (C) and the upper clamp (D) over the outer tube and in- stall the four socket-head cap screws (E) finger tight.
  • Page 7 Installing Brushcutter Blade 1. Turn the unit over so that the gearcase output shaft faces UP. 2. Align the hole in the holder with the notch in the gearcase flange, and then temporarily lock the output shaft by inserting a hex wrench through both holes.

  • Page 8: Shoulder Strap

    Shoulder Strap Adjust the shoulder strap so the shoulder pad rests comfortably on the off-side shoulder and the cutting path of the cutting attachment is parallel to the ground. Tighten hanger screw. WARNING! Always wear a shoulder strap when operating this unit with a blade. A shoulder strap is also recommended when using trimmer line.
  • Page 9 NOTES...
  • Page 10 NOTES...
  • Page 11 NOTES...
  • Page 12 If you require assistance or have questions concerning the application, operation or maintenance of this product you may call the Shindaiwa Consumer Product Support Department at 1-877-986-7783 from 8:30 am to 4:30 pm (Central Standard Time) Monday through Friday. Before calling, please know the model and serial number of your unit.