Advertisement
Quick Links
Model No. WESY85100
Serial No.
Write the serial number in the space
above for future reference.
Serial Number Decal--
QUESTIONS?
As a manufacturer, we are com-
miffed to providing complete
customer satisfaction.
If you have
questions, or find that there are
missing or damaged parts, we
will guarantee you complete sat-
isfaction through direct assis-
tance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE
CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate
assis-
tance, free of charge to you.
CUSTOMER
HOT LINE:
1-800-225-0653
Mon.-Fri., 6 a.m.-6 p.m. MST
PATENT PENDING
USER'S MANUAL
Advertisement
Related Manuals for Weider 8510
Summary of Contents for Weider 8510
- Page 1 PATENT PENDING Model No. WESY85100 Serial No. Write the serial number in the space above for future reference. Serial Number Decal-- QUESTIONS? As a manufacturer, we are com- miffed to providing complete customer satisfaction. If you have questions, or find that there are missing or damaged parts, we will guarantee you complete sat- isfaction through direct assis-...
-
Page 2: Table Of Contents
TABLE OF CONTENTS LIMITED WARRANTY ..............IMPORTANT PRECAUTIONS .............. BEFORE YOU BEGIN ..............ASSEMBLY ................HOW TO USE THE HOME GYM SYSTEM ........... TROUBLE-SHOOTING AND MAINTENANCE ..........CABLE DIAGRAM ..............PART LIST ................EXPLODED DRAWING ..............ORDERING REPLACEMENT PARTS ..........Back Cover Note: A PART IDENTIFICATION CHART is attached to the center of this manual. -
Page 4: Before You Begin
BEFORE YOU BEGIN Thank you for selecting the versatile WELDER®8510 Service Department toll-free at 1-800-225-0653, Home Gym System. The WELDER ®8510 offers a Monday through Friday, 6 a.m. until 6 p.m. Mountain selection of weight stations designed to develop every Time (excluding holidays). -
Page 5: Assembly
Before beginning assembly, carefully read the following information .and instructions: all parts are oriented as shown in the drawings. Place all parts of the WEIDER 8510 in a cleared Tighten all parts as you assemble them, unless area and remove the packing materials; do not instructed to do otherwise. - Page 6 Slide the Front Upright (42) onto the 5/16" x 2 1/2" Carriage Bolts (1). Hand-tighten a 5/16" Nylon Locknut (3) onto each Carriage Bolt. Do not tighten the Nylon Locknuts yet. Press a 1" Square Inner Cap (65) into the Front Upright (42).
- Page 7 Press the Weight Tube Bumper (64) into the end of the Weight Tube (63). Insert the Weight Holes Tube into the stack of Weights (25). Be sure that the pins on the Weight Tube are sitting in the pin grooves in the top Weight. Lubricate the inside of the holes in the Top Weight.
- Page 8 Press a 1 3/4" Square Inner Cap (44) into the ° top of a Press Arm (46). Press a 1" Round Inner Cap (49) into each end of the handle on the Press Arm. Attach the Press Arm to one side of the Press Frame (17) with two 5/16"...
- Page 9 As you assemble the cables and pulleys in steps 10 through 18, please refer to the CABLE DIAGRAM on page 17 of this manual. 10. Route the Long Cable (23) around the 3 1/2" Pulley (15) attached to the Top Frame (55). Be sure that the end of the Cable with the ball is on the indicated side o_fthe Pulley...
- Page 10 14. Route the Long Cable (23) around the 3 1/2" Pulley (15) attached to the bracket on the Top Bracket _. ,_._12 Frame (55). Tighten the 3/8" x 2" Bolt (12) and the 3/8" Nylon Locknut (21). (Note: This Pulley is pre-assembled. It has been shown disassembled for easy part identifi-...
- Page 11 17. Route the Short Cable (58) around the 3 1/2" 17-b Pulley (15) attached to the upper hole in the Press Frame (17). Be sure that the Cable Trap (66) is in the "3 o'clock" position that the Cable is routed around the Pulley as shown, Tighten the 3/8"...
- Page 12 21. Press a 1 1/2" Square Inner Cap (32) into the Leg Lever (29). Lubricate the 5/16" x 2 1/4" Bolt (33). Attach the Leg Lever (29) to the Seat Frame (36) with the 5/16" x 2 1/4" Bolt and a 5/16" Nylon Locknut (3).
- Page 13 24. Remove the decals from the Decal Sheet (not shown) and apply them to the home gym system in the loca- tions shown in the illustration below. HIGH PULLEY BUTTERFLY 8510 BENCH PRESS LEG CURL LOW PULLEY 25. Make sure that all parts have been properly tightened. Use of the remaining parts will be explained in HOW TO USE THE HOME GYM SYSTEM, beginning on page 14 of this manual.
-
Page 14: How To Use The Home Gym System
HOW TO USE THE HOME GYM SYSTEM The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise poster accompanying this manual to see how the home gym system should be set up for each exercise. IMPOR- TANT: When attaching the lat bar or nylon strap, make sure that the attachments are in the correct... - Page 15 ATTACHING AND REMOVING THE SEAT I1 b 424o Set the bracket on the Seat Frame (36) onto the indF cated pin on the Front Uptight (42). Attach the Seat r .36 Frame to the Front Upright with the 5/16" x 2 3/4" Carriage Bolt (14) and the Seat Knob (40).
-
Page 16: Trouble-Shooting And Maintenance
TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts often and replace any worn parts immediately. The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the home gym system, can stretch slightly when it is first used. -
Page 17: Cable Diagram
CABLE DIAGRAM The cable diagram below shows the proper routing of the Short Cable (58) and the Long Cable (23). Use the diagram to be sure that the two cables have been assembled correctly. If the cables have not been correctly routed, the home gym system will not function properly and damage may occur.