Power Failure - Viking VGSC3674BSS Use And Care Manual

Before startingtheSelf-Clean c ycle:
1. Remove t he ovenracks, r acksupports, a ndanyotheritems/utensils
fromtheoven. Thehighheatgenerated duringthecleaning cycle
candiscolor, warp,anddamage theseitems.Donot usefoil or
liners in the oven.Duringthe Self-Clean c ycle, f oil canburnor melt
anddamage the ovensurface.
2. Wipeoff anylargespillsfromthe ovenbottomandsides.Never
useovencleaners i nsidea self-cleaning ovenor on raised portions
of thedoor.
3. Someareas of the ovenmustbecleaned by handbeforethe cycle
begins.Soilintheseareas will be baked on andverydifficult t o
cleanif not removed first. Cleanthedoorupto the gasket, t he
doorframe, a ndupto two inches insidetheframewithdetergent
andhot water.Rinse thoroughly anddry.
TostarttheSelf-Clean c ycle:
1. Close the ovendoorcompletely.
2. TurntheOvenFunction selector k nobclockwise t o the self-clean
mode.At thistimethecleanindicator l ightwill comeon.
3. Turn the Temperature Control k nobpastthe cleansettinguntilthe
knobstops.At thistime,thetemperature i ndicator l ightwill come
on andwithin30 seconds, theautomatic doorlatchengages. T he
temperature i ndicator l ightwill remain onuntilthe ovenreaches t he
self-clean t emperature a ndwill thencycleon andoff duringthe
cycle.
4. Thecleaning cyclewill lastapproximately 3 1/2hourswithan
additional 3 0 minutes needed forthe ovento cooldownenough for
the doorlatchto disengage.
5. Whenthe cycleiscompleted, turn boththe OvenFunction selector
andtheTemperature Control k nobto "OFF" At thistimethe clean
indicator l ightwill go off.
6. Whenthe ovenhascompletely cooled, o pendoorandremove any
ashfromthe ovensurfaces w itha dampcloth.
To stop the Self-clean cycle:
To cancel or interrupt the self-cleaning cycle, turn both the
Temperature Control knob and Oven Function selector to "OFF".
When the oven temperature drops to a safe temperature, the
automatic door latch will release and the oven door can be opened.
Replacing Interior Oven Lights
CAUTION: DISCONNECT THE ELECTRIC POWER AT THE MAIN FUSE
OR CIRCUIT BREAKER BEFORE REPLACING BULB. Do not touch bulb
with bare hands. Clean any signs of oil off of the bulb and handle with
a soft cloth.
1. Unsnap glass light cover at opposite
end from metal hinge.
2. Firmly grasp light bulb and pull out.
3. Replace with a 64405, 12V-5W bulb.
4. Replace the light cover by first
sliding into metal hinge and then
snapping close on opposite end.
5. Reconnect power at the main fuse or
circuit breaker.
Metal
hinc
Glass light cover
Light
bulb
Power Failure
If power failure occurs, the electric ignitors will not work. The range
surface burners can still be used, but only when the burners are lit
manually with a match. The griddle cannot be used at all. Do not
attempt to operate the oven. Make sure the oven control is in the
"OFF" position.
Due to safety considerations and the possibility of personal injury in
attempting to light and extinguish the burner, the grill should, under no
circumstances, be used during a power failure. The grill burner control
should always remain in the "OFF" position during a power failure.
Momentary power failure can occur unnoticed. The range is affected
only when the power is interrupted. When it comes back on, the range
will function properly without any adjustments. A "brown-out" may or
may not affect range operation, depending on how severe the power
loss is.
If the range is in the self-clean cycle when the power failure occurs,
wait until power is restored and allow door to unlock automatically.
Turn all controls off and restart self-clean cycle again, according to
instructions.
36 37