Table of Contents
Advertisement
unpacking
and assernbay
d
With
the fence
in its normal
position
(next
to the front
table),
loosen
the yoke
clamp
handle,
lift
up on swivel
latch
pin
knob
and rotate
the yoke
as shown
to index
the
yoke
90 °
from
the
cross
cut
position.
This
will
locate
the saw blade
between
the motor
and the motor
and the fence.
Loci{
the yoke
by
tightening
the yoke
clamp handle.
e
Position
carriage
until
the edge of the blade,
when spun
by hand,
just touches
the front
face of the fence.. The
rip-scale
indicator
(on the right
hand side of radial
arm)
should
now
read
"0"
inches
on lower
portion
of
the
"In-Rip"
scale_
If
not,
loosen
screws
and
shift
the
indicator
until
it
is aligned
with
the "0"
marl<,
then
tighten
the screws.
NOTE:
With
the saw
blade
and fence
in the position
shown,
the tower
portion
of the "In-Rip:
scale is used
If the fence
is re-located
at the extreme
rear position,
the upper
portion
of the "In-Rip"
scale would
be used
The "Out-Rip"
scale indicator
on the left
hand
side of
the radial
arm is adjusted
in essentially
the same manner
as the "In-Rip"
indicator,
except
the fence should
be at
extreme
rear
and the blade
positioned
as shown
With
12 inches
measured
between
the fence
(when
in full
rear position)
and the face
of saw blade,
the rip-scale
indicator
should
be positioned
to read 12 inches on the
upper portion
of the "Out-Rip"
scale.
NOTE:
With
the saw blade
and fence
in the position
shown,
the
upper
portion
of
the
"Out-Rip"
scale
is
used.
If the fence
is moved
to normal
position
(at the
rear of front
table)
the lower
portion
of the "Out-Rip"
scale is used.
F_NC_
FRONT
TAgL£
J
_A_L_
_AR
1
S_ACE_
BOARD
__,6LE
RI_' SCALE
_NDICA_OR
CARRIAG_ LOC_ ÷_NOB
!.
t
!
"
F_NC_
R_AR
TA_L_
TABLE
5}_ACE_
BOARD
g
Loosen
the
yoke
clamp
handle,
lift
up on the swivel
latch pin knob
and return
the blade to the 90 ° position°
operating
controls
RIP SCAL_
INDtCATOR
ON-OFF
SWITCH
WITH
KEY
SCALE
SWIVEL
LATCH
PiN
KNO_
AND
INDICATOR
ARM LATCH
LEV
COR D
ARM
LATCH
CARRIAGE
LOCK
KNOB
GUARD
CLAMP
ANT!
KICKBACK
SPREADER ASSEMBLY
B_VEL
LOCK
KNOB
ELEVATION
CRANK
.LATCH
PIN HANDLE
BEVEL
INDEX
SCALE
KNOW LOCATIONS
AND FUNCTIONS
OF CONTROLS
A series of six diagrams
is located
on the top surface
of the
radial
arm. These
designate
the controls
that
must
be used
in
basic
set-ups
and
operating
procedures.
You
should
become
familiar
with
these
diagrams
and
the
operating
instructions
that follow,
before
operating
your
saw
14
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
