Table of Contents
Advertisement
3.
If the insert
is BELOW
the table
surface,
remove
the
insert
and bend
the tabs
(with
pliers)
enough
to make
the insert ABOVE
the table surface.
4.
To replace
insert.
Place
insert
into
insert
opening
in
table
and
push
toward
rear
of
saw
to
engage
spring
clip
and
until
keyslot
in insert will drop
over screw.
Tighten
screw.
DO NOT TIGHTEN
SCREW TO THE POINT WHERE IT
DEFLECTS THE INSERT.
CHECKING
BLADE SQUARENESS TO TABLE
IMPORTANT:
BLADE
must
be SQUARE
(90 ° ) to
TABLE, in order to proceed with assembly.
To check for blade squareness, refer to "BLADE
TILT, OR
SQUARENESS
OF BLADE TO TABLE"
adjustments on
page 25.
NOTE: The Combination
Square must be "TRUE"
- See
start of "Unpacking
and Checking Contents section on page
6 for checking method.
CHECKING BLADE FOR HEEL
IMPORTANT:
Saw blade MUST be parallel to miter gauge
groove.
To
check
for
parallelism,
refer
to
"HEELING
ADJUSTMENT
OR PARALLELISM
OF SAWBLADE
TO
MITER GAUGE GROOVE"
adjustment on page 24.
CHECKING
BLADE
ELEVATION
Maximum
depth
of
cut
MUST
NOT
EXCEED
TWO
INCHES.
This
adjustment
is set at the factory
and should
be checked
to make
sure
that
it has not changed
due to
rough
handling
during
shipment.
\
MAKE SURE SQUARE
IS NOT TOUCHING
TIP OF TOOTH
With the blade
up as high as it will go, measure
the distance
from
the top of the table to top of the highest
saw tooth.
If
it is more than
two
(2) inches,
adjust
it at this time.
Refer
to "BLADE
ELEVATION'"
adjustments
on page 26.
ATTACHING
AND ASSEMBLING
TABLE EXTENSIONS
If
you
received
two
Table
Extensions
with
your
saw
(furnished
with
Model
No.
113.242720)
assemble
and
attach
them
at this time.
1.
Position
saw upside
down
on floor.
NOTE:
To
protect
the
finished
surfaces
of the saw and
extensions,
lay a piece of heavy paper on the floor.
2.
From
among
the
loose parts
find
the two
loose parts
bags for table extensions.
8 Hex Head Screws 5/16-18
x 1¼ in. long
8 Lockwashers,
5/16
in. External
Type
(approx.
dia. of hole 5/16
in.)
8 Flat Washers
(dia. of hole 11/32
in.)
4 Flat Washers
(dia. of hole 17/64)
8 Hex
Nuts,
5/16-18
(approx.
dia. of hole 5/16
in.)
16 truss head screws 1/4-20
x 1
4 corner
support
brackets
4 corner
stiffener
brackets
16 Hex nut 1/4-20
16 Iockwashers,
1/4"
External
Type
3.
Install
support
corner
brackets,
stiffener
corner
brackets,
screws,
Iockwashers,
washers,
and
nuts
for
assembling
extensions
as shown
. . . tighten
screws
attaching
extensions
to
table
SLIGHTLY.
BE
SURE
END
OF
EXTENSIONS
ARE
EVEN
WITH
FRONT
EDGE
OF SAW.
4.
Leave saw in upside
down
position
until
you
attach
the
rip fence guide bars and legs.
LOCKWASHER
SCREW
II
Hide quick links:
Advertisement
Table of Contents
