Table of Contents
Advertisement
1-800-944-9044
(United
States)
1
Visit our web site at
1-800-265-8352
(Canada)
1
ww_.crosley.com
CONCERN
POTENTIAL
CAUSE
I
COMMON
SOLUTION
AUTOMATIC
ICE MAKER
* Turn on ice maker. For the fresh food ice maker, press and
hold the "Ice Off" button for 4 seconds until the indicator turns
off. For the freezer ice maker, lower the wire signal arm.
Connect the unit to the household water supply and ensure
the supply valve is open.
Ensure that the supply line does not kink when the refrigera-
tor is pushed into place against the wall.
Remove and re-install the water filter.
Be sure to push the
filter firmly so that you hear it lock solidly into position.
If water dispenses slowly or not at all, or if the filter is six (6)
months old or older, it should be replaced.
Turn off household water line valve. Remove valve. Ensure
that valve is not a self-piercing saddle valve. Clean valve.
Replace valve if necessary.
, The fresh food and freezer ice makers wiil each produce
approximately
2.5 pounds of ice every 24 hours depending
on usage conditions.
e If water dispenses slower than normal; or if the filter is six
(6)
months old or older, it should be replaced.
o Ensure that the supply line does not kink when the refrigera-
tor is pushed into place against the wal!:
Turn off household water line valve. Remove va!ve. Ensure
that valve is not a self-piercing saddle valve. Clean valve.
Replace valve if necessary.
Move the item and release wire signal arm.
Remove any ice
cubes that may have frozen together over the wire signal
arm.
• Remove ice container and di_scardice. The ice maker will
produce fresh supply.
Ice should be used at east twice
weekly to keep the cubes separated.
• This genera!!y occurs when the ice maker does not get
enough water. This is usually the result of a c!ogged water
filter.
Replace the water filter.
_®
_,
•
,
,
f/
•
See the Ice maker _snot making any ice section above.
Be sure the refrigerator doors are completely d0Sed:
0The
motor oVerioad protector Will reset in about three (3)
minutes and then ice can be dispensed:
Ice maker
is not mak =
• Ice maker is turned off.
mg any ice.
Refrigerator is not connected to wa-
ter line or water valve is not open.
The water supply line is kinked.
The water filter is not seated
properly.
The water filter may be clogged
with foreign material.
Saddle valve on cold water pipe
is clogged or restricted by foreign
material.
Tee maker
is not mak_
OIce maker is producing
less ice
ing enough ice,
than you expect.
The water filter may be dogged
with foreign material:
, The water supp!y line is tdnked.
• Saddle Valve on €old Water pipe
is clogged or restricted by foreign
material:
Freezer ice maker
will
• Ice maker wire signal arm is be-
not stop making
ice.
ing held down by some package
in the freezer that has fallen
against the ice maker.
Tce cubes
are freezing
,, Ice cubes are not being used
frequent!y enough,
• Ice cubes are hollow (shells of
ce with water inside)i The hollow
cubes break open in the bin and
leak their water onto existing ice,
which causes it to freeze together.
ICE DISPENSER
Dispenser
will not dis:
' There is noice in the bin t0be
pense ice.
dispensed:
, The refrigerator doors are not corn:
pletely closed:
t Dispenser padd!e has been pressed
too long and the dispenser motor
has overheated.
Ice dispenser
is
• Ice has melted and frozen around au-
• Remove ice container, thaw, and empty the contents.
Clean
jammed,
get due to infrequent use, temper_re
container, wipe dry, and replace in proper position.
When
fluctuations, and/or power outages,
new ice is made, dispenser should operate.
Ice cubes are jammed between ice
• Remove ice cubes that are jamming the dispenser.
maker and back of ice container.
OPENING/CLOSING
OF DOORS/DRAWERS
Close both doors gently.
Door(s) will not close.
• Door was closed too hard, causing
other door to open slightly.
Refrigerator is not level. It rocks
on the floor when moved slightly.
Refrigerator is touching a wall or
cabinet.
Drawers are
dimcult
to
'
Food is tOuching shelf On topof
move,
drawer.
....
Track that drawers slide on isdirty.
* Ensure floor is level and solid, and can adequately support the re-
frigerator. Contact a carpenter to correct a sagging or sloping floor.
Ensure floor is level and solid, and can adequately support the re-
frigerator. Contact a carpenter to correct a sagging or sloping floor.
Remove top layer of items in drawer.
Ensure drawer is properly installed on track.
i Clean drawei, rollers, and track:
See (:::are & Cleaning:
Advertisement
Table of Contents
