Advertisement
IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING...
To set up a master TV you will need to know how to
enter the L20V54S Installer
menu and make changes to
the default values as required.
If necessary, familiarize
yourself
with the L20V54S Installer
menu and how to
make and save changes in the menu, before attempting
to clone the
L20V54S Master TV setup.
You will also need an InstaLLer remote
control similar to the one
shown in the front of this manual.
Finally, the TV's c[onable features
need to be set up. This is a
critical
step. If the Master TV display panel's c[onable features
Like
adding channel icons or channel labels are not correctly added, then
the cloned L20V54SsTVswill all have problems.
As the cloning
procedure is being performed,
specific steps need to
be done at the indicated
times to achieve the desired result. Be sure
to do each task as indicated.
If a procedure or step is [eft out or not
performed completely,
cloning
may not work. At each step, pay
attention
to assure the TV screen shows the proper message when
cloning.
If the message indicated
does not appear, there is a
problem with that step and cloning
may not be successful.
Cloning
is only possible when the signal source is an Analog channel,
not a
digital
channel.
Making
a Master
TV
Detailed Instructions
The following
describes the procedure for preparing
a Master
L20V54S for cloning
and the procedure for adding Channel Icons
and/or
Labels.
*Note: I: Disconnect art Aux inputs. Under certain conditions, Auto Program
Scan is disabled if there is an Aux input active.
i.
Enter the L20V54S installer
menu.
a. Reset the internal
controller
to factory default
by accessing
installer
menu item 117 FACT DEFAULT, set it to i and press
"ENTER'[ The value wil! change back to 0 after the TV's internal
controller
has been restored to factory default condition.
b. Within
the Installer
menu, set the Installer
menu items to the
configuration
required of your institution.
c. It is important
to set the tuning
band at this time, see
Installer
menu item 03 BAND/AFC.
d. Set Installer
menu item 28 - CH OVERIDE to 001 to allow
access to the Auto Program and Channel List/Channel
Label
features in the Channel Menu. Exit the Installer
menu.
2. Access the Master TV menus and set the c[onable options
on the
menus to the desired configuration.
Refer to the CLonabLe Menu
Features
Chart on see page 52.
3. Run Auto Program.
4. Enter the Channel List/Channel
Label menu and edit the channel
line-up to include the Free-To-Guest Channels only.
5. Assign ICONs to the channels using the Channel Label Menu.
*Note:
Youcan add Channel ICONStypically network togos like ABC,NBC,
PBS etc. in this step. Or, in Step 7, add Channel ICONSor labels for
channels without Icons.
6. Transfer the TV setup: Enter the L20V54S installer
menu.
Press '2', '5', '5', 'MENU' to start the transfer of the TV's setup to
the L20V54S. Once the transfer is complete,
the system will exit
the Installer
menu.
*Note: Only do 2-5-5 + MENUonce. The TVsetup may be corrupted if
255 + Menu is clone more than one time.
7. Edit/Add
Channel ICONs and Channel Labels as needed.
Enter Installer
menu. With menu displayed,
press 2-5-4 + MENU.
See page 50 for detailed
instructions:
- Editing/Adding Channel ICON and Labels on Master TV
- Changing a Channel's ICON on Master TV
- Changing/Adding Channel Labels on Master TV
- Changing Source Labels on Master TV
8. VerifyMaster TV setup and featureconfiguration:
, Did you add Channel ICONS?
, Did you add Channel Labels?
, Did you add Aux Source Labels?
, Did you adjust all TV menu optionsas required?
The TV master setup isnow ready to be cloned.Go to the master
TV cloningsectionor continueon to page 53.
PAGE
52
Advertisement
