Table of Contents
Advertisement
Basic
Settings
ANALOG
: Select this for the analog input mode.
(Initial
setting when shipped
from the
factory.)
If the following
symptoms
occur while playing
Dolby Digital
or
DTS Digital
Surround
software
with "DIGITAL
AUTO"
selected,
follow the procedure
below.
• Sound does not come out at the beginning
of playback.
° Noise
comes out while searching
or skipping
chapters
or tracks.
2
Press INPUT
DIGITAL
(or ANALOG/DIGITAL
on the remote
control).
° "DIGITAL
AUTO"
appears
on the display.
Press CONTROL
UP A/DOWN
•
to select
"DOLBY
DIGITAL"
or "DTS
SURROUND"
while
"DIGITAL
AUTO"
still remains
on the
display.
° Each time you press
the button,
the digital input mode
changes
as follows:
When
"DOLBY
DIGITAL"
or "DTS
SURROUND"
is selected,
"DIGITAL
AUTO"
goes off.
=-'_[]
TGTTFIL_
._
FI"T nu u
• To play back software
encoded
with Dolby Digital,
select
"DOLBY
DIGITAL."
° To play back software
encoded
with DTS Digital
Surround,
select "DTS
SURROUND."
Note:
When you turn off the power or select another source, "DOLBY
DIGITAL" and "DTS SURROUND" are canceled and the digital input
mode is automatically
reset to "DIGITAL AUTO."
The followings
are the analog/digital
signal indicators
on the display
to indicate
what type of the signal comes into the receiver.
ANALOG
LINEAR PCM
N["I DIGITAL
: Lights when the analog input is selected.
: Lights when Linear PCM signals
come in.
: ° Lights when Dolby Digital signals come in.
° Flashes
when "DOLBY
DIGITAL"
is
selected
for software
not encoded
with
Dolby
Digital
signals.
: ° Lights
when DTS signals
come in.
° Flashes
when "DTS SURROUND"
is
selected
for software
not encoded
with DTS
signals.
Note:
When "DIGITAL AUTO" cannot recognize the incoming signals, no
digital signal indicators light up on the display.
To obtain
the best possible
sound or effect from the Surround
modes
(see page 18), register
the following
speakers
and subwoofer
information
after all connections
are completed.
The followings
are items you can set:
• Subwoofer
information--SUBWOOFER
• Speaker
size--FRNT
SP, CNTR
SP, REAR
SP
° Speaker
distance--UNIT,
FRNT DIS, CNTR DIS, REAR DIS
° Crossover
frequency--CROSS
° Low frequency
effect attenuator--LFE
ATT
° Dynamic
range compression--D.
COMP
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step I again.
"YES" for the subwoofer and "SMALL"
for the front, center
and rear speakers are initial settings. To get best possible
sound, change the subwoofer and speaker settings to fit your
listening conditions.
Subwoofer
information
Register
whether
you have connected
a subwoofer
or not.
Press SETTING
repeatedly
until
_E.,.G
"SUBWOOFER"
(with the current
_'_')
setting) appears
on the display.
2 Press CONTROL
UP A/DOWN
• to
CO.T.OL
DOWN
UP
register whether
you have connected
a
"
"
subwoofer
or not.
i
L!
• Each time you press the button,
the subwoofer
setting alternates
between
"YES"
and "NO."
NO
: Select this when you have not connected or have
disconnected a subwoofer.
12
Hide quick links:
Advertisement
Table of Contents
