Grill Lighting Instructions; Using The Side Burner - Nexgrill 720-0033 Use And Care Manual

WARNING: IMPORTANT!
BEFORE LIGHTING...
Inspect the gas supply piping or hose prior to turnin
gas "ON". If there is evidence of cuts, wear, or abrasion,
it must be replaced prior to use. Do not use the grill i
odor of gas is present. The pressure regulator and
assembly supplied with the u
su bstitute regulators for those supplied with the grill. If a
replacement is necessary , contact the factory for proper
replacement.
Screw the regulator (type QCC1) onto the tank. Leak
check the hose and regulator connections with a soap and
water solution before operating the grill (see assembly
instruction).
TO LIGHT THE GRILL BURNER:
Turn all knobs to "OFF" then turn on the gas supply.
A lways keep your face and body as far from the grill as
possible when lighting.
Open the lid, push and turn one
position and press the electric igniter for 3 to 4 secon
WARNING: IMPORTANT!

USING THE SIDE BURNER:

Inspect the gas supply piping or hose prior to turning the
gas "ON". If there is evidence of cuts, wear or abrasion,
it must be replaced prior to use. Do not use the side
burner if the odor of gas is present.
WARNING: Always keep your face and body as far
away from the burner as possible when lighting.
LIGHTING INSTRUCTIONS
To light side burner, remove any cooking utensils from
the burner grate. Push and turn the control knob
counterclockwise to the "HI" position. This will start the
gas flowing. Press the electric igniter for 3 to 4 seconds
to light the burner. If the burner does not light within 4
seconds, turn the control knob to "OFF". If the smell of
gas is detected and the igniter is not functioning,
i mmediately turn the control knob "OFF". Allow 5
m inutes for any accumulated gas to dissipate, and then
se e the following section for "MATCH LIGHTING".
M ATCH LIGHTING
H old a lit extended match or lighter near the burner
p orts; turn the control knob counterclockwise to "HI".
Move your hand away immediately once the burner is lit.

GRILL LIGHTING INSTRUCTIONS

g the
f the
hose
nit must be used. Never
control knob to the "HI"
ds
USING THE SID
to light the burner. If the burner does not light, wait for 5
minutes then retry.
TO MATCH LIGHT THE GRILL:
If the burner will not light after several attempts then the
burner can be match lit.
If you've just attempted to light the burner with the
igniter, allow 5 minutes for any accum
d issipate. Keep your face and hands as far away from the
grill as possible. Insert a lit extended match or lighter
through the cooking grids to the burner. Press the co
k nob and rotate left to the HI setting, which should
release the gas. Burner will light immediately.
P ush and turn the control knob, which is centered on the
bu rner to "HI". If the burner does not light in 4 seconds
turn the knob off, wait 5 minutes and try again.
Keep a spray bottle of soapy water near the gas supply
valve and check the connections before each use.
Do not attempt to light the grill if odor of gas is present.
Call for service 1-800-913-8999.
E BURNER
Rotate the control knob to the desired setting. Check for
proper burner flame characteristics. Each burner is
adjusted prior to shipment; however, variations in the
local gas supply may take minor adjustments necessary.
Burner flames should be blue and stable with no yellow
tips, excessive noise, or lifting. If any of these conditions
exist call our customer service line. If the flame is
yellow, it indicates insufficient air. If the flame is noisy
and tends to lift away from the burner, it indicates too
much air.
S TAINLESS STEEL
The grill is made from non-rusting and non-magnetic
304 stainless steel. There are many different stainless
steel cleaners available. Always use the mildest cleaning
procedure first, scrubbing in the direction of the grain.
To touch up noticeable scratches in the stainless steel,
sand very lightly with dry 100 grit emery papers in the
direction of the grain. Specks of grease can gather on the
surfaces of the stainless steel and bake on to the surface
and give the appearance of rust. For removal use an
abrasive pad in conjunction with a stainless steel cleaner.
12
ulated gas to
ntrol