Related Manuals for Enterasys Enterasys Gold Distributed Forwarding Engine 4H4202-72
Summary of Contents for Enterasys Enterasys Gold Distributed Forwarding Engine 4H4202-72
- Page 1 Enterasys Matrix ® DFE-Gold Series Hardware Installation Guide Module 4H4282-49 Module 4H4283-49 Module 4H4203-72 Module 4H4202-72 Module 4H4284-49 9033906-05...
- Page 3 Part Number: 9033906‐05 July 2008 ENTERASYS NETWORKS, ENTERASYS MATRIX, LANVIEW, MATRIX, ENTERASYS NETSIGHT, WEBVIEW, and any logos associated therewith, are trademarks or registered trademarks of Enterasys Networks, Inc., in the United States and other countries. For a complete list of Enterasys trademarks, see http://www.enterasys.com/company/trademarks.aspx.
-
Page 4: Regulatory Compliance Information
Regulatory Compliance Information Federal Communications Commission (FCC) Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment uses, generates, and can radiate radio frequency energy and if not installed in accordance with the operator’s manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense. WARNING: Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Industry Canada Notice This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada. Class A ITE Notice WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Clase A. Aviso de ITE ADVERTENCIA: Este es un producto de Clase A. En un ambiente doméstico este producto puede causar interferencia ... -
Page 5: Hazardous Substances
This product complies with the following: 47 CFR Parts 2 and 15, CSA C108.8, 2004/108/EC, EN 55022, EN 61000‐3‐2, EN 61000‐3‐3, EN 55024, AS/NZS CISPR 22, VCCI V‐3. Este producto de Enterasys cumple con lo siguiente: 47 CFR Partes 2 y 15, CSA C108.8, 2004/108/EC, EN 55022, EN 55024, EN 61000‐3‐2, EN 61000‐3‐3, AS/NZS CISPR 22, VCCI V‐3. Elektro- magnetische Kompatibilität ( EMC ) Dieses Produkt entspricht den folgenden Richtlinien: 47 CFR Parts 2 and 15, CSA C108.8, 2004/108/EC, EN 55022, EN 61000‐3‐2, EN 61000‐3‐3, EN 55024, AS/NZS CISPR 22, VCCI V‐3. This product complies with the requirements of European Directive, 2002/95/EC, Restriction of Hazardous Substances (RoHS) in Electrical and Electronic Equipment. European Waste Electrical and Electronic Equipment (WEEE) Notice In accordance with Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment (WEEE): The symbol above indicates that separate collection of electrical and electronic equipment is required and that this product was placed on the European market after August 13, 2005, the date of enforcement for Directive 2002/96/EC. When this product has reached the end of its serviceable life, it cannot be disposed of as unsorted municipal waste. It must be collected and treated separately. It has been determined by the European Parliament that there are potential negative effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment. It is the users’ responsibility to utilize the available collection system to ensure WEEE is properly treated. For information about the available collection system, please go to www.enterasys.com/support/ Electromagnetic Compatibility (EMC) Compatibilidad Electromágnetica (EMC) Hazardous Substances or contact ... - Page 6 Enterasys Customer Support at 353 61 705586 (Ireland). (Parts) (Metal Parts) Circuit Modules) Cables & Cable Assemblies) (Plastic and Polymeric parts) Circuit Breakers) Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T 11363-2006 standard. Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T 11363-2006 standard.
- Page 7 VCCI Notice This is a class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. BSMI EMC Statement — Taiwan This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
-
Page 8: Safety Information
Do not use optical instruments to view the laser output. The use of optical instruments to view laser output increases eye hazard. When viewing the output optical port, power must be removed from the network adapter. Application of Council Directive(s): 2004/108/EC European Representative Address: Enterasys Networks, Ltd. Conformance to Directive(s)/Product Standards: EC Directive 2004/108/EC Equipment Type/Environment: Networking Equipment, for use in a Commercial Enterasys Networks, Inc. declares that the equipment packaged with this notice conforms to the above directives. Safety Information Class 1 Laser Transceivers Declaration of Conformity 2006/95/EC Manufacturer’s Name: Enterasys Networks, Inc. Manufacturer’s Address: 50 Minuteman Road Andover, MA 01810 Nexus House, Newbury Business Park London Road, Newbury Berkshire RG14 2PZ, England EN 55022 EN 61000‐3‐2 EN 61000‐3‐3 EN 55024 EC Directive 2006/95/EC EN 60950 EN 60825... - Page 9 ENTERASYS NETWORKS, INC. FIRMWARE LICENSE AGREEMENT BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. This document is an agreement (“Agreement”) between the end user (“You”) and Enterasys Networks, Inc., on behalf of itself and its Affiliates (as hereinafter defined) (“Enterasys”) that sets forth Your rights and obligations with respect to the Enterasys software program/firmware (including any accompanying documentation, hardware or media) (“Program”) in the package and prevails over any additional, conflicting or inconsistent terms and conditions appearing on any purchase order or other document submitted by You. “Affiliate” means any person, partnership, corporation, limited liability company, other form of enterprise that directly or indirectly through one or more intermediaries, controls, or is controlled by, or is under common control with the party specified. This Agreement constitutes the entire understanding between the parties, with respect to the subject matter of this Agreement. The Program may be contained in firmware, chips or other media. BY INSTALLING OR OTHERWISE USING THE PROGRAM, YOU REPRESENT THAT YOU ARE AUTHORIZED TO ACCEPT THESE TERMS ON BEHALF OF THE END USER (IF THE END USER IS AN ENTITY ON WHOSE BEHALF YOU ARE AUTHORIZED TO ACT, “YOU” AND “YOUR” SHALL BE DEEMED TO REFER TO SUCH ENTITY) AND THAT YOU AGREE THAT YOU ARE BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES, AMONG OTHER PROVISIONS, THE LICENSE, THE DISCLAIMER OF WARRANTY AND THE LIMITATION OF LIABILITY. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT OR ARE NOT AUTHORIZED TO ENTER INTO THIS AGREEMENT, ENTERASYS IS UNWILLING TO LICENSE THE PROGRAM TO YOU AND YOU AGREE TO RETURN THE UNOPENED PRODUCT TO ENTERASYS OR YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS FOLLOWING THE DATE OF RECEIPT FOR A FULL REFUND. IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT ENTERASYS NETWORKS, LEGAL DEPARTMENT AT (978) 684‐1000. You and Enterasys agree as follows: LICENSE. You have the non‐exclusive and non‐transferable right to use only the one (1) copy of the Program ...
- Page 10 APPLICABLE LAW. This Agreement shall be interpreted and governed under the laws and in the state and federal courts of the Commonwealth of Massachusetts without regard to its conflicts of laws provisions. You accept the personal jurisdiction and venue of the Commonwealth of Massachusetts courts. None of the 1980 United Nations Convention on the Limitation Period in the International Sale of Goods, and the Uniform Computer Information Transactions Act shall apply to this Agreement. EXPORT RESTRICTIONS. You understand that Enterasys and its Affiliates are subject to regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of certain technical products to certain countries, unless a license to export the product is obtained from the U.S. Government or an exception from obtaining such license may be relied upon by the exporting party. If the Program is exported from the United States pursuant to the License Exception CIV under the U.S. Export Administration Regulations, You agree that You are a civil end user of the Program and agree that You will use the Program for civil end uses only and not for military purposes. If the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export Administration Regulations, in addition to the restriction on transfer set forth in Section 1 or 2 of this Agreement, You agree not to (i) reexport or release the Program, the source code for the Program or technology to a national of a country in Country Groups D:1 or E:2 (Albania, Armenia, Azerbaijan, Belarus, Cambodia, Cuba, Georgia, Iraq, Kazakhstan, Laos, Libya, Macau, Moldova, Mongolia, North Korea, the People’s Republic of China, Russia, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other countries as may be designated by the United States Government), (ii) export to Country Groups D:1 or E:2 (as defined herein) the direct product of the Program or the technology, if such foreign produced direct product is subject to national security controls as identified on the U.S. Commerce Control List, or (iii) if the direct product of the technology is a complete plant or any major component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major component thereof, if such foreign produced direct product is subject to national security controls as identified on the U.S. Commerce Control List or is subject to State Department controls under the U.S. Munitions List. UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Program (i) was developed solely at private expense; (ii) contains “restricted computer software” submitted with restricted rights in accordance with section 52.227‐19 (a) through (d) of the Commercial Computer Software‐Restricted Rights Clause and its successors, and (iii) in all respects is proprietary data belonging to Enterasys and/or its suppliers. For Department of Defense units, the Program is considered commercial computer software in accordance with DFARS section 227.7202‐3 and its successors, and use, duplication, or disclosure by the U.S. Government is subject to restrictions set forth herein. DISCLAIMER OF WARRANTY. EXCEPT FOR THOSE WARRANTIES EXPRESSLY PROVIDED TO YOU IN WRITING BY ENTERASYS, ENTERASYS DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NON‐INFRINGEMENT WITH RESPECT TO THE PROGRAM. IF IMPLIED WARRANTIES MAY NOT BE DISCLAIMED BY APPLICABLE LAW, THEN ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THIRTY (30) DAYS AFTER DELIVERY OF THE PROGRAM TO YOU.
- Page 11 AUDIT RIGHTS. You hereby acknowledge that the intellectual property rights associated with the Program are of critical value to Enterasys, and, accordingly, You hereby agree to maintain complete books, records and accounts showing (i) license fees due and paid, and (ii) the use, copying and deployment of the Program. You also grant to Enterasys and its authorized representatives, upon reasonable notice, the right to audit and examine during Your normal business hours, Your books, records, accounts and hardware devices upon which the Program may be deployed to verify compliance with this Agreement, including the verification of the license fees due and paid Enterasys and the use, copying and deployment of the Program. Enterasys’ right of examination shall be exercised reasonably, in good faith and in a manner calculated to not unreasonably interfere with Your business. In the event such audit discovers non‐compliance with this Agreement, including copies of the Program made, used or deployed in breach of this Agreement, You shall promptly pay to Enterasys the appropriate license fees. Enterasys reserves the right, to be exercised in its sole discretion and without prior notice, to terminate this license, effective immediately, for failure to comply with this Agreement. Upon any such termination, You shall immediately cease all use of the Program and shall return to Enterasys the Program and all copies of the Program. OWNERSHIP. This is a license agreement and not an agreement for sale. You acknowledge and agree that the Program constitutes trade secrets and/or copyrighted material of Enterasys and/or its suppliers. You agree to implement reasonable security measures to protect such trade secrets and copyrighted material. All right, title and interest in and to the Program shall remain with Enterasys and/or its suppliers. All rights not specifically granted to You shall be reserved to Enterasys. 10. ENFORCEMENT. You acknowledge and agree that any breach of Sections 2, 4, or 9 of this Agreement by You may cause Enterasys irreparable damage for which recovery of money damages would be inadequate, and that Enterasys may be entitled to seek timely injunctive relief to protect Enterasys’ rights under this Agreement in addition to any and all remedies available at law. 11. ASSIGNMENT. You may not assign, transfer or sublicense this Agreement or any of Your rights or obligations under this Agreement, except that You may assign this Agreement to any person or entity which acquires substantially all of Your stock assets. Enterasys may assign this Agreement in its sole discretion. This Agreement shall be binding upon and inure to the benefit of the parties, their legal representatives, permitted transferees, successors and assigns as permitted by this Agreement. Any attempted assignment, transfer or sublicense in violation of the terms of this Agreement shall be void and a breach of this Agreement. 12. WAIVER. A waiver by Enterasys of a breach of any of the terms and conditions of this Agreement must be in writing and will not be construed as a waiver of any subsequent breach of such term or condition. Enterasys’ failure to enforce a term upon Your breach of such term shall not be construed as a waiver of Your breach or prevent enforcement on any other occasion. 13.
-
Page 13: Table Of Contents
Overview of DFE-Gold Series Capabilities ...1-1 The DFE-Gold Modules ...1-2 Connectivity ...1-6 Management ...1-7 Switch Configuration Using WebView ...1-7 Switch Configuration Using CLI Commands ...1-7 Standards Compatibility ...1-7 Secure Networks Policy Support ...1-7 LANVIEW Diagnostic LEDs ...1-8 Chapter 2: Network Requirements 10BASE-T Network ...2-1... - Page 14 DFE-Gold Module Specifications ... A-1 COM Port Pinout Assignments ... A-3 Regulatory Compliance ... A-4 Appendix B: Mode Switch Bank Settings and Optional Installations Required Tools ... B-1 Setting the Mode Switches ... B-2 Memory Locations and Replacement Procedures ... B-5 DIMM Replacement Procedure (4H4282-49 and 4H4283-49) ...
- Page 15 LANVIEW LEDs on 4H4282-49, 4H4283-49, and 4H4203-72 ...4-2 LANVIEW LEDs on 4H4202-72...4-3 LANVIEW LEDs on 4H4284-49...4-4 OFFLINE/RESET Switch...4-9 Mode Switch Location on 4H4282-49 and 4H4283-49... B-3 Mode Switch Location on 4H4203-72... B-3 Mode Switch Location on 4H4202-72... B-4 Mode Switch Location on 4H4284-49... B-4 DIMM/DRAM SIMM Locations (for 4H4282-49, 4H4283-49, 4H4284-49)...
- Page 16 Tables Contents of DFE-Gold Module Carton...3-2 LANVIEW LEDs...4-5 Troubleshooting Checklist ...4-7 Specifications ... A-1 COM Port Pin Assignments... A-3 Compliance Standards ... A-4...
-
Page 17: About This Guide
This guide provides an overview, installation and troubleshooting instructions, and specifications for the Enterasys Matrix 4H4202‐72, 4H4284‐49 modules. For information about the CLI (Command Line Interface) set of commands used to configure and manage the DFE‐Gold modules, refer to the Enterasys Matrix DFE‐Gold Series Configuration Guide. Note: In this guide, the following terms are used: • • • Depending on the firmware version used in the DFE-Gold module, some features described in this document may not be supported. Refer to the Release Notes shipped with the DFE-Gold module to determine which features are supported. -
Page 18: How To Use This Guide
How to Use This Guide How to Use This Guide This preface provides an overview of this guide and the DFE‐Gold Series manual set, and a brief summary of each chapter; defines the conventions used in this document; and instructs how to obtain technical support from Enterasys Networks. To locate information about various subjects in this guide, refer to the following table: For... An overview of the DFE-Gold modules Network requirements that must be met before installing the DFE-Gold modules Instructions to install the DFE-Gold module hardware... -
Page 19: Conventions Used In This Guide
Conventions Used in This Guide The following conventions are used in this guide: Note: Calls the reader’s attention to any item of information that may be of special importance. Caution: Contains information essential to avoid damage to the equipment. Precaución: Contiene información esencial para prevenir dañar el equipo. Achtung: Verweißt auf wichtige Informationen zum Schutz gegen Beschädigungen. -
Page 20: Getting Help
• The device history (for example, have you returned the device before, is this a recurring problem) • Any previous Return Material Authorization (RMA) numbers xviii About This Guide www.enterasys.com/services/support/ 1-800-872-8440 (toll-free in U.S. and Canada) or 1-978-684-1000 For the Enterasys Networks Support toll-free number in your country: www.enterasys.com/services/support/contact/ support@enterasys.com To expedite your message, type [SWITCHING] in the subject line. -
Page 21: Chapter 1: Introduction
Depending on the firmware version used in the DFE-Gold module, some features described in this document may not be supported. Refer to the Release Notes shipped with the DFE-Gold module to determine which features are supported. Overview of DFE-Gold Series Capabilities The Gold Distributed Forwarding Engine (DFE) is Enterasys Networks’ next generation of enterprise modules for the Matrix N‐Series and Matrix E7 switches. These DFE modules deliver high performance and flexibility to ensure comprehensive switching, routing, Quality of Service, security, and traffic containment. Key features include: •... -
Page 22: The Dfe-Gold Modules
DFE-Gold modules (4xxxxx) only. Do not insert 7xxxxx modules or other legacy modules into the same chassis with 4xxxxx modules as this will render the chassis inoperable. The DFE‐Gold module ports can be configured to control traffic by limiting the rate of traffic accepted into the module and prioritizing traffic to expedite the flow of higher priority traffic through the module. The DFE‐Gold module receives power and backplane connectivity when it is inserted into the chassis. The information concerning how to configure the DFE module features are provided in the Enterasys Matrix DFE‐Gold Series Configuration Guide. 4H4282-49 The 4H4282‐49 is an edge‐network switch with 48, 10BASE‐T/100BASE‐TX compliant ports, through fixed front panel RJ45 connectors and an option slot for a network expansion module. Each of the fixed front panel ports can operate in either half‐duplex or full‐duplex mode of operation. The duplex mode can be determined by either auto‐ negotiation or manual configuration. 4H4283-49 The 4H4283‐49 is an edge‐network switch with 48, 10BASE‐T/100BASE‐TX compliant ports through four fixed front‐panel RJ21 connectors and an option slot for a network expansion module. Each of the fixed front panel ports can operate in either half‐duplex or full‐duplex mode of operation. The duplex mode can be determined by either auto‐... - Page 23 full‐duplex mode of operation. The duplex mode can be determined by either auto‐ negotiation or manual configuration. 4H4202-72 The 4H4202‐72 has 72, 10BASE‐T/100BASE‐TX compliant ports, through fixed front panel RJ45 connectors. Each of the fixed front panel ports can operate in either half‐duplex or full‐duplex mode of operation. The duplex mode can be determined by either auto‐ negotiation or manual configuration. 4H4284-49 The 4H4284‐49 DFE‐Gold module has 48, 100BASE‐FX compliant ports, through fixed front panel MT‐RJ connectors and a slot for the optional network expansion module. Enterasys Matrix DFE-Gold Series Modules Hardware Installation Guide 1-3 The DFE-Gold Modules...
-
Page 24: 4H4282-49, 4H4283-49, And 4H4203-72 Dfe-Gold Modules
The DFE-Gold Modules Figure 1-1 4H4282-49, 4H4283-49, and 4H4203-72 DFE-Gold Modules È 1 OFFLINE/RESET button 2 RJ45 COM (Console Port) 3 CPU LED 4 MGMT LED 5 GROUP SELECT button 1-4 Introduction À À Á Á Â Â Ã Ã Ä... -
Page 25: 4H4202-72 And 4H4284-49 Dfe-Gold Modules
Figure 1-2 4H4202-72 and 4H4284-49 DFE-Gold Modules È 1 OFFLINE/RESET switch 2 RJ45 COM (Console Port) 3 CPU LED 4 MGMT LED 5 4H4202-72 - Group 3, 24 Ports, 10/100, through RJ45s 4H4284-49 - NEM option slot À Á Â... -
Page 26: Connectivity
Connectivity Connectivity 4H4282-49 Depending on how the 4H4282‐49 (Figure • 48, 10BASE‐T/100BASE‐TX switched ports connected through 48 fixed, RJ45 front‐panel connectors, or • 48, 10BASE‐T/100BASE‐TX switched ports connected through 48 fixed, RJ45 front‐panel connectors and an optional network expansion module. 4H4283-49 Depending on how the 4H4283‐49 (Figure • 48, 10BASE‐T/100BASE‐TX switched ports connected through four fixed RJ21 front‐panel connectors, or • 48, 10BASE‐T/100BASE‐TX switched ports connected through four fixed RJ21 front‐panel connectors and an optional network expansion module. 4H4203-72 The 4H4203‐72 has 10BASE‐T/100BASE‐TX compliant ports through six RJ21 front panel connectors. 4H4202-72 The 4H4202‐72 has 72, 10BASE‐T/100BASE‐TX compliant ports, through 72 fixed front panel RJ45 connectors. 4H4284-49 Depending on how the 4H4284‐49 (Figure • 48, 100BASE‐FX compliant ports, through 48, fixed front‐panel MT‐RJ connectors, or • 48, 100BASE‐FX compliant ports, through 48, fixed front‐panel MT‐RJ connectors and an optional network expansion module. 1-6 Introduction 1‐1) is configured, it can support up to: 1‐1) is configured, it can support up to: 1‐1) is configured, it can support up to:... -
Page 27: Management
Management Management of the module can be either in‐band or out‐of‐band. In‐band remote management is possible using Telnet, Enterasys Networks’ NetSight application, or WebView™ application. Out‐of‐band management is provided through the RJ45 COM (Communication) port on the front panel using a VT100 terminal or a VT100 terminal emulator. Switch Configuration Using WebView Enterasys Networks’ HTTP‐based Web management application (WebView) is an intuitive web tool for simple management tasks. Switch Configuration Using CLI Commands The CLI commands enable you to perform more complete switch configuration management tasks. For CLI command set information and how to configure the module, refer to the Enterasys Matrix DFE‐Gold Series Configuration Guide. Standards Compatibility The DFE‐Gold modules are fully compliant with the IEEE 802.3‐2002, 802.3ae‐2002, 802.1D‐1998, and 802.1Q‐1998 standards. The DFE‐Gold module provides IEEE 802.1D‐1998 Spanning Tree Algorithm (STA) support to enhance the overall reliability of the network and protect against “loop” conditions. Secure Networks Policy Support Policy Enabled Networking manages the allocation of networking infrastructure resources in a secure and effective manner. Using Secure Networks Policy, an IT Administrator can predictably assign appropriate resources to the Users, Applications, and Services that use the network; while blocking or containing access for inappropriate or potentially dangerous network traffic. Using this technology it is possible, for the first time, to align IT services with the needs of specific users and applications, and to leverage the network as a key component of the organization’s security strategy. -
Page 28: Lanview Diagnostic Leds
LANVIEW Diagnostic LEDs • Network Services are logical groups of Classification Rules that identify specific networked applications or services. Users may be permitted or denied access to these services based on their role within the organization. Priority and bandwidth rate limiting may also be controlled using Network Services. • Behavioral Profiles (or roles) are used to assign Network Services to groups of users who share common needs–for example Executive Managers, Human Resources Personnel, or Guest Users. Access, resources, and security restrictions are applied as appropriate to each Behavioral Profile. A variety of authentication methods including 802.1X, EAP‐TLS, EAP‐TTLS, and PEAP may be used to classify and authorize each individual user; and the IT Administrator may also define a Behavioral Profile to apply in the absence of an authentication framework. LANVIEW Diagnostic LEDs LANVIEW diagnostic LEDs serve as an important troubleshooting aid by providing an easy way to observe the status of individual ports and overall network operations. 1-8 Introduction... -
Page 29: Chapter 2: Network Requirements
• 100BASE‐FX Fiber‐Optic Network (page 2‐2) The network installation must meet the requirements to ensure satisfactory performance of this equipment. Failure to do so will produce poor network performance. Note: The Enterasys Matrix DFE-Gold Series Configuration Guide and the Cabling Guide referred to in the following sections can be found on the Enterasys Networks World Wide Web site: Refer to 10BASE-T Network When connecting a 10BASE‐T segment to any of the module fixed front panel ports of the 4H4282‐49, 4H4283‐49, 4H4203‐72, and 4H4202‐72, ensure that the network meets the ... -
Page 30: 100Base-Tx Network
100BASE-TX Network 100BASE-TX Network Fixed front panel ports of the 4H4282‐49, 4H4283‐49, 4H4203‐72, and 4H4202‐72 provide a connection that supports Category 5 UTP cabling. The device at the other end of the twisted pair segment must meet IEEE 802.3‐2002 100BASE‐TX Fast Ethernet network requirements for the devices to operate at 100 Mbps. Refer to the Cabling Guide for details. Note: The fixed ports of the module support Category 5 UTP cabling with an impedance between 85 and 111 ohms for 100 Mbps operation. The module is capable of operating at either 10 or 100 Mbps. The module automatically senses the speed of the other device and adjusts its speed accordingly. -
Page 31: Chapter 3: Installation
Electrical Hazard: Only qualified personnel should perform installation procedures. Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion. Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden. Read the Release Notes shipped with the DFE-Gold module to check for any exceptions to the supported features and operation documented in this guide. -
Page 32: Installation Site Requirement
Installation Site Requirement Installation Site Requirement The DFE‐Gold module must be installed in a Matrix E7, N1, N3, N5, or N7 chassis located in a Restricted Access Location (RAL). This location should only be accessible by people that have been trained or are technically competent enough to be aware of potential risks of accessing the hazardous areas of the chassis. Locations such as a locked wiring closet or locked cabinet meet this requirement. Warning: Install this module in a Matrix E7, N1, N3, N5, or N7 chassis that has been installed in a Restricted Access Location only. Access to the equipment by users must be restricted through the use of a tool or lock and key or other means of security and is controlled by the authority responsible for the location. -
Page 33: Installing Optional Network Expansion Module
Installing Optional Network Expansion Module A Phillips screwdriver is required to install an optional network expansion module into the 4H4282‐49, 4H4283‐49, or 4H4284‐49. Note: Install any optional equipment before proceeding to the section, Placement and Installation Rules,” different series modules in a Matrix E7 chassis. Refer to your release notes or the Enterasys Networks web site for the latest available network expansion modules. Installing a NEM involves • removing the coverplate from the DFE‐Gold module (4H4282‐49, 4H4283‐49, or 4H4284‐49), • installing the NEM, and •... -
Page 34: Examples, Slot Numbers/Module Placement In Matrix E7 Chassis
DFE Module Placement and Installation Rules Figure 3-1 To ensure proper operation of the system, consider the following examples and rules for module placement in either chassis. Example 1 (Figure Shows one module installed in the chassis. If the chassis is populated with only one 4xxxxx, it must be installed in slot 1. Rule: If only one 4xxxxx is installed in the chassis, it must be in slot 1. Always install a 4xxxxx in slot 1 of the chassis. Example 2 (Figure Shows the chassis fully populated with 4xxxxx modules. All modules may be hot swapped, except the module in slot 1. If the module in slot 2 is designated as a redundant management module, the module in slot 1 may be hot swapped without shutting down the system. The module in slot 2 can be designated using the CLI command set license <license key>. For information on how to use this command, refer to the Enterasys Matrix DFE‐Gold Series Configuration Guide. To access this guide on the web, refer to “Related Documents” on page xvi. Without a designated redundant management module in slot 2, removing the module in slot 1 will shut down the system. Rule: Any module in a 4xxxxx system, including the management module in slot 1, may be hot swapped when there is a 4xxxxx module designated as a redundant management module in slot 2. 3-4 Installation Examples, Slot Numbers/Module Placement in Matrix E7 Chassis 3-1, A) 3-1, B) -
Page 35: Installing Module Into A Chassis
Example 3 (Figure Shows the primary management module missing from slot 1. As long as the module installed in slot 2 is designated as a redundant management module, the module in slot 1 can be removed without affecting system operation. However, if there is no module in slot 1, and the system is powered down, it cannot be restarted without a module in slot 1. Caution: When installing a module into slot 1 of a non-operating chassis, it is strongly recommended that the module have the desired version of firmware. Installation of a replacement module into slot 1 of a non-operating chassis requires reconfiguration of the system settings. -
Page 36: Preparation
Installing Module into a Chassis Preparation Remove the blank panel covering the slot in which the module will be installed. All other slots must remain covered to ensure proper airflow for cooling. (Save the blank plate in the event you need to remove the module.) Remove the module from the shipping box. (Save the box and packing materials in the event the module needs to be reshipped.) Locate the antistatic wrist strap shipped with the chassis. Attach the antistatic wrist strap to your wrist and plug the cable from the antistatic wrist strap into the ESD grounding receptacle at the upper right corner of the chassis. Remove the module from the plastic bag. (Save the bag in the event the module must be reshipped.) Observe all precautions to prevent damage from Electrostatic Discharge (ESD). Examine the module for damage. If any damage exists, DO NOT install the module. Immediately contact Enterasys Networks. Refer to “Getting Help” on page xviii. Installing Module into Matrix E7 or N7 Chassis To install the module, refer to Figure Caution: To prevent damaging the backplane connectors in the following step, take care that the module slides in straight and properly engages the backplane connectors. - Page 37 Align the module card between the upper and lower card guides of the desired slot and slide it into the chassis, taking care that the module slides in straight. See Caution below. Caution: Due to the amount of force needed to properly seat the module connectors into the backplane connectors, it is best to apply force to the end of the levers to insert (or eject) the module. Otherwise, damage could result to the module and chassis. Precaución: Para colocar los conectores del módulo en los conectores del panel posterior correctamente es necesario hacer bastante fuerza, por ello, para insertar o quitar el módulo, se recomienda concentrar la fuerza en el extremo de las palancas.
-
Page 38: Installing Module Into Matrix E7 Or N7 Chassis (Matrix E7 Shown)
Installing Module into a Chassis Figure 3-2 Installing Module into Matrix E7 or N7 Chassis (Matrix E7 shown) ➆ ➂ ➃ ➀ 1 Card guides 2 Slot number 1(right-most slot is 7) 3 Module card 4 Metal back panel 3-8 Installation ➁... -
Page 39: Installing Module Into Matrix N1, N3, Or N5 Chassis
Installing Module into Matrix N1, N3, or N5 Chassis Caution: Failure to observe static safety precautions could cause damage to the DFE module. Follow static safety handling rules and wear the antistatic wrist strap. Do not cut the non-conductive bag to remove the module. Sharp objects contacting the board or components can cause damage. -
Page 40: Connecting To The Network
Connecting to the Network Figure 3-3 ➆ ➄ 1 Card guides 2 Slot 1 (Top slot is slot 3.) 3 Module card 4 Metal back panel Connecting to the Network For connecting unshielded twisted pair (UTP) segments from the network or other devices, refer to • Connecting UTP Cables to 4H4282‐49 or 4H4202‐72 (page 3‐11) • Connecting UTP Cables to 4H4283‐49 or 4H4203‐72 (page 3‐15) For fiber‐optic connections, refer to • Connecting Fiber‐Optic Cables to 4H4284‐49 (page 3‐18) Note: If the DFE-Gold module is being installed in a network using Link Aggregation, there are rules concerning the network cable and port configurations that must be followed for... -
Page 41: Connecting Utp Cables To 4H4282-49 Or 4H4202-72
Connecting UTP Cables to 4H4282-49 or 4H4202-72 The fixed RJ45 front panel connections of the 4H4282‐49 and 4H4202‐72 are 10/100 Mbps ports. The ports have internal crossovers, and also support automatic‐polarity sensing when configured for automatic‐negotiation. If automatic‐negotiation is not activated on a port, use a straight‐through cable when connecting a workstation to the port. When connecting a networking device to the port, such as a bridge, repeater, or router, use a crossover cable. If a port is set for auto‐negotiation, automatic‐polarity sensing is also activated. Automatic‐polarity sensing eliminates the need for a crossover cable, regardless if the connection is to another network device or a workstation. Note: All RJ45 front panel ports on the 4H4282-49 and 4H4202-72 Unshielded Twisted Pair (UTP) cabling with an impedance between 85 and 111 ohms. Category 3 cable may be used if the connection is going to be used only for 10 Mbps. -
Page 42: Connecting A Twisted Pair Segment With Rj45 Connector
Connecting to the Network Figure 3-4 1 RJ45 connector Verify that a link exists by checking that the port RX (Receive) LED is ON (flashing amber, blinking green, or solid green). If the RX LED is OFF and the TX (Transmit) LED is not blinking amber, perform the following steps until it is on: To view the receive and transmit activity on a group of segments, press the GROUP SELECT button (see Figure through 4). Each time the GROUP SELECT button is pressed, the GROUP LED lights up in sequence, indicating which Group is selected. The receive and transmit activity for that group of segments is then indicated by the RX and TX LEDs for each segment. b. Verify that the cabling being used is Category 5 UTP with an impedance between 85 and 111 ohms. If the port is to operate at 100 Mbps, category 5 cabling must be used. Verify that the device at the other end of the twisted pair segment is on and properly connected to the segment. d. Verify that the RJ45 connectors on the twisted pair segment have the proper pinouts and check the cable for continuity. Typically, a crossover cable is used between hub devices. A straight‐through cable is used to connect between switches or hub devices and an end user (computer). Refer to Figure Figure 3‐6 for four‐wire RJ45 connections. Refer to Figure 3‐7 and Figure eight‐wire RJ45 connections. 3-12 Installation Connecting a Twisted Pair Segment With RJ45 Connector Á... -
Page 43: Four-Wire Crossover Cable Rj45 Pinouts, Connections Between Hub Devices
Figure 3-5 Four-Wire Crossover Cable RJ45 Pinouts, Connections Between Hub Devices À Ã 1 RJ45 device port 2 Other device port Figure 3-6 Four-Wire Straight-Through Cable RJ45 Pinouts, Connections Between Switches and End-User Devices À Ã 1 RJ45 device port 2 Other device port Â... -
Page 44: Eight-Wire Crossover Cable Rj45 Pinouts, Connections Between Hub Devices
Connecting to the Network Figure 3-7 Devices 1 RJ45 device port 2 Other device port Figure 3-8 Between Switches and End-User Devices 1 RJ45 device port 2 Other device port 3-14 Installation Eight-Wire Crossover Cable RJ45 Pinouts, Connections Between Hub À... -
Page 45: Connecting Utp Cables To 4H4283-49 Or 4H4203-72
Ensure that the twisted pair connection meets the dB loss and cable specifications outlined in the Cabling Guide. Refer to “Related Documents” on page xvi for information on obtaining this document. If a link is not established, contact Enterasys Networks. Refer to “Getting Help” on page xviii for details. Repeat steps 1 through 3 above, until all connections have been made. Connecting UTP Cables to 4H4283-49 or 4H4203-72 The 4H4283‐49 and 4H4203‐72 have fixed RJ21 connectors. Each RJ21 connector can support up to 12 segments. You can use either straight RJ21 cable connectors or right‐ angle RJ21 connectors with optional RJ21 angle adapters. To connect a UTP segment to the 4H4283‐49 or 4H4203‐72, proceed as follows: Ensure that the device connected to the other end of the segment is powered ON. If using RJ21 straight connectors, proceed to step optional RJ21 angle adapters, proceed to step If using an RJ21 straight connector, refer to Figure RJ21 right‐angle cable connectors, proceed to Step Plug the RJ21 straight connector into the appropriate RJ21 port connector. b. Tighten the two screws to secure the RJ21 straight connector to the RJ21 port connector. Note: The cable pinouts for a 25-pair cable (RJ21) can be found in the Cabling Guide. Refer to “Related Documents”... -
Page 46: Connecting A Twisted Pair Using Rj21 Straight Connector
Connecting to the Network Figure 3-9 1 RJ21 straight connector 2 RJ21 port connector To install an RJ21 right‐angle connector, refer to Figure Note: When installing more than one RJ21 right-angle connector, start with the bottom- most front-panel RJ21 connector so that the cables will dress properly over the front panel as shown in If using an optional RJ21 angle adapter available from Enterasys Networks, insert ... -
Page 47: Connection Using Optional Rj21 Angle Adapter
Figure 3-10 Connection Using Optional RJ21 Angle Adapter Á Â Ä À Ã Â Ä 1 RJ21 angle adapter 2 RJ21 port connector 3 Retaining screws 4 RJ21 right-angled connector Å Æ 5 Retaining clips 6 GROUP SELECT button 7 Example showing how multiple cables would be arranged along the front panel. -
Page 48: Connecting Fiber-Optic Cables To 4H4284-49
Connecting to the Network Verify that a link exists by checking that the port RX (Receive) LED is ON (flashing amber, blinking green, or solid green). If the RX LED is OFF and the TX (Transmit) LED is not blinking amber, perform the following steps until it is on: To view the receive and transmit activity on a group of segments, press the GROUP SELECT button to step to the group of interest (Groups 1 through 4). Each time the GROUP SELECT button is pressed, the GROUP LED lights up in sequence, indicating which Group is selected. The receive and transmit activity for that group of segments is then indicated by the RX and TX LEDs for each segment. b. Verify that the cabling being used is Category 5 UTP with an impedance between 85 and 111 ohms. If the port is to operate at 100 Mbps, category 5 cabling must be used. Verify that the device at the other end of the twisted pair segment is on and properly connected to the segment. d. Verify that the RJ21 connector on the twisted pair segment has the proper pinouts and check the cable for continuity. Check that the twisted pair connection meets the specifications in the Cabling Guide. If a link is not established, contact Enterasys Networks. Refer to “Getting Help” on page xviii for details. Repeat all the steps above until all RJ21 connections are made. Connecting Fiber-Optic Cables to 4H4284-49 This section provides the procedures to connect fiber‐optic cables from the 100BASE‐FX, MT‐RJ front panel ports of the 4H4284‐49 to the network or other devices. Each fiber‐optic link consists of two fiber‐optic strands within the cable: Transmit (TX) and Receive (RX) The transmit strand from a DFE‐Gold module port connects to the receive port of a fiber‐... -
Page 49: Connecting A Fiber-Optic Segment To Mt-Rj Front Panel Connector
1 MT-RJ front panel connecto 2 MT-RJ cable connector 3 Release tab À Á Å Ã Ä Â 4 Receive LED (RX) 5 Transmit LED (TX) 6 GROUP SELECT switch Matrix DFE-Gold Series Modules Hardware Installation Guide 3-19 Connecting to the Network... -
Page 50: Connecting To Com Port For Local Management
Connecting to COM Port for Local Management This section describes how to install a UTP straight‐through cable with RJ45 connectors and optional adapters to connect a PC, a VT series terminal, or a modem to an Enterasys Networks module to access Local Management. This section also provides the pinout assignments of the adapters. Note: The RJ45 COM port connector is located in approximately the same location on all DFE-Gold modules. In the following procedures, the 4H4282-49 COM port is shown as an example in the figures associated with each procedure. -
Page 51: Connecting To An Ibm Pc Or Compatible Device
With a UTP straight‐through cable and RJ45‐to‐DB25 female adapter, you can connect products equipped with an RJ45 COM port to a VT series terminal or VT type terminals running emulation programs for the VT series. With a UTP straight‐through cable and an RJ45‐to‐DB25 male adapter, you can connect products equipped with an RJ45 COM port to a Hayes compatible modem that supports 9600 baud. Connecting to an IBM PC or Compatible Device To connect an IBM PC or compatible device, running the VT terminal emulation, to an Enterasys Networks module COM port (Figure Connect the RJ45 connector at one end of a UTP straight‐through cable to the communications COM port on the Enterasys Networks module. (The COM port is also known as a Console port.) Plug the RJ45 connector at the other end of the UTP straight‐through cable into an RJ45‐to‐DB9 adapter. Connect the RJ45‐to‐DB9 adapter to the communications port on the IBM PC. Turn on the PC and configure your VT emulation package with the following parameters: Parameter Mode Transmit Bits Parity Stop Bit When these parameters are set, the Local Management password screen will display. Refer to the appropriate Enterasys Matrix DFE‐Gold Series Configuration Guide for further information. Connecting to COM Port for Local Management 3‐12), proceed as follows:... -
Page 52: Connecting To A Vt Series Terminal
Connecting to COM Port for Local Management Figure 3-12 1 UTP straight-through cable with RJ45 connectors 2 RJ45 COM port Connecting to a VT Series Terminal To connect a VT Series terminal to an Enterasys Networks DFE‐Gold module COM port (Figure 3‐13), use a UTP straight‐through cable with RJ45 connectors and an RJ45‐to‐DB25 female adapter, and proceed as follows: Connect the RJ45 connector at one end of the UTP straight‐through cable to the COM port on the Enterasys Networks module. Plug the RJ45 connector at the other end of the UTP straight‐through cable into the RJ45‐to‐DB25 female adapter. Connect the RJ45‐to‐DB25 adapter to the port labeled COMM on the VT terminal. Turn on the terminal and access the Setup Directory. Set the following parameters on your terminal:... -
Page 53: Connecting To A Modem
When these parameters are set, the Local Management password screen will display. Refer to the Enterasys Matrix DFE‐Gold Series Configuration Guide for further information. Figure 3-13 Connecting a VT Series Terminal à 1 UTP straight-through cable with RJ45 connectors 2 RJ45 COM port Connecting to a Modem To connect a modem to an Enterasys Networks DFE‐Gold module COM port (Figure 3‐14), use a UTP straight‐through cable with RJ45 connectors and an RJ45‐to‐DB25 male adapter, and proceed as follows: Connect the RJ45 connector at one end of the UTP straight‐through cable to the COM port of the DFE‐Gold module. Plug the RJ45 connector at the other end of the UTP straight‐through cable into the RJ45‐to‐DB25 modem adapter. Connect the RJ45‐to‐DB25 adapter to the communications port on the modem. Turn on the modem. Connecting to COM Port for Local Management Â... -
Page 54: Connecting To A Modem
Connecting to COM Port for Local Management With a PC connected to a remote modem, you can configure the switch remotely. To accomplish this, you must configure your PC VT emulation package with the following parameters. Parameter Mode Transmit Bits Parity Stop Bit When these parameters are set, the Local Management password screen will display. Refer to the Enterasys Matrix DFE‐Gold Series Configuration Guide for further information. Figure 3-14 1 UTP straight-through cable with RJ45 connectors 2 RJ45 COM port 3 RJ45-to-DB25 modem adapter 3-24 Installation Connecting to a Modem Ä... -
Page 55: Adapter Wiring And Signal Assignments
Adapter Wiring and Signal Assignments RJ45 Conductor Blue Green Orange Yellow VT Series Port Adapter Wiring and Signal Diagram RJ45 Conductor Blue Yellow Green Orange COM Port Adapter Wiring and Signal Diagram DB25 Matrix DFE-Gold Series Modules Hardware Installation Guide 3-25 Connecting to COM Port for Local Management Signal Receive (RX) -
Page 56: Completing The Installation
Completing the Installation Modem Port Adapter Wiring and Signal Diagram RJ45 Completing the Installation Completing the DFE module installation depends on if the module is being installed in: • a new DFE module system (refer to “Completing the Installation” on page 3‐26), or • an established, operating DFE module system (refer to “Completing the Installation of a DFE‐Gold Module in an Existing System” on page 3‐28). Completing the Installation of a New System In a new system of DFE modules, one of the installed DFE modules will become the management module on chassis power up, and all DFE modules will automatically be set to the factory default values. A complete list of the factory default values are provided in Chapter 3 of the Enterasys Matrix DFE‐Gold Series Configuration Guide. After installing all DFE‐Gold modules into the host chassis and making the connections to the network, proceed to “First‐Time Log‐In Using a Console Port Connection” on page 3‐27 to access the module management startup screen from your PC, terminal, or modem connection. 3-26 Installation DB25 Conductor Blue... - Page 57 First-Time Log-In Using a Console Port Connection Note: This procedure applies only to initial log-in, and to logging in to a device not yet configured with administratively-supplied user and password settings. By default, the Matrix DFE Series device is configured with three user login accounts: ro for Read-Only access;...
-
Page 58: Completing The Installation Of A Dfe-Gold Module In An Existing System
Andover, MA 01810-1008 U.S.A. Phone: +1 978 684 1000 E-mail: support@enterasys.com WWW: http://www.enterasys.com (c) Copyright Enterasys Networks, Inc. 2003 Chassis Serial Number: Chassis Firmware Revision: xx.xx.xx Matrix N7(su)-> Completing the Installation of a DFE-Gold Module in an Existing System In an established DFE‐Gold module system, •... - Page 59 Logging in with an Administratively-Configured User Account If the device’s default user account settings have been changed, proceed as follows: At the login prompt, enter your administratively‐assigned user name and press ENTER. At the Password prompt, enter your password and press ENTER. The notice of authorization and the Matrix prompt displays as shown back in Figure Note: Users with Read-Write (rw) and Read-Only access can use the set password command to change their own passwords. Administrators with Super User (su) access can use the set system login command to create and change user accounts, and the set password command to change any local account password.
- Page 60 Completing the Installation 3-30 Installation...
-
Page 61: Chapter 4: Troubleshooting
This chapter provides information concerning the following: • Using LANVIEW (page 4‐1) • Troubleshooting Checklist (page 4‐7) • Overview of DFE‐Gold Module Shutdown Procedure (page 4‐9) • Recommended Shutdown Procedure Using OFFLINE/RESET Switch (page 4‐10) • Last Resort Shutdown Procedure Using OFFLINE/RESET Switch (page 4‐10) Unless otherwise noted, the following information applies to all DFE‐Gold modules. Using LANVIEW The modules use a built‐in visual diagnostic and status monitoring system called LANVIEW. The LANVIEW LEDs (Figure status to aid in diagnosing network problems. About the Management (MGMT) LED The MGMT LED (shown in Figure Management Module to control the management functions for all DFE‐Gold modules in the chassis. The Management Module handles all IP requests to the chassis IP address, such as PING, Telnet, SNMP, HTTP, etc. The Management Module also handles the CLI configuration sessions through the console port. So, when you plug into a DFE‐Gold module COM port to configure a DFE‐Gold module in the chassis, it is handled by the Management Module regardless of the DFE‐Gold module COM port that you use. Troubleshooting 4‐1) allow quick observation of the network ... -
Page 62: Lanview Leds On 4H4282-49, 4H4283-49, And 4H4203-72
Using LANVIEW Viewing Receive/Transmit Activity on 4H4282-49, 4H4283-49, and 4H4203-72 On the 4H4282‐49, 4H4283‐49, and 4H4203‐72 you can view the receive and transmit activity on the RX and TX LEDs. However, only one group of 12 ports may be viewed at a time. To view the receive and transmit activity on a group of attached segments, press the GROUP SELECT button (see Figure 4). Each time the GROUP SELECT button is pressed, the GROUP LED lights up in sequence, indicating which group is selected. The receive and transmit activity for that group of segments is then indicated by the RX and TX LEDs for each port. Figure 4-1 1 MGMT LED 4-2 Troubleshooting 4‐1) to step to the group of interest (Groups 1 through LANVIEW LEDs on 4H4282-49, 4H4283-49, and 4H4203-72 À Á 2 Group 1, Port 1 status LEDs... -
Page 63: Lanview Leds On 4H4202-72
Using LANVIEW Viewing Receive/Transmit Activity on 4H4202-72 On the 4H4202‐72, you can view the receive and transmit activity on the RX and TX LEDs. However, only one group of 24 ports may be viewed at a time. To view the receive and transmit activity on a group of attached segments, press the GROUP SELECT button (see Figure 4‐2) to step to the group of interest (Groups 1 through 3). Each time the GROUP SELECT button is pressed, a GROUP LED lights up in sequence, indicating which group is selected. The receive and transmit activity for that group of segments is then indicated by the RX and TX LEDs for each port. Figure 4‐2 shows Group 3 selected and the location of Group 3, port 1 RX and TX LEDs. Figure 4-2 LANVIEW LEDs on 4H4202-72 À Á Â 1 MGMT LED 2 Group 3, Port 1 status LEDs 3 Group 3 select LED Matrix DFE-Gold Series Modules Hardware Installation Guide 4-3... -
Page 64: Lanview Leds On 4H4284-49
Using LANVIEW Viewing the Receive and Transmit Activity on 4H4284-49 On the 4H4284‐49 DFE‐Gold module, you can view the receive and transmit activity on the RX and TX LEDs. However, only one group of 12 ports may be viewed at a time on the 4H4284‐49. To view the receive and transmit activity on a group of segments, press the GROUP SELECT button (see Figure time the GROUP SELECT button is pressed, the GROUP LED lights up in sequence, indicating which group is selected. The receive and transmit activity for that group of segments is then indicated by the RX and TX LEDs for each port. Figure 4-3 1 MGMT LED Table 4‐1 describes the LED indications and provides recommended actions as appropriate. Note: The terms flashing, blinking, solid, and Alternately used in the following: Flashing indicates an LED is flashing randomly. Blinking indicates an LED is flashing at a steady rate (approximately 50% on, 50% off). -
Page 65: Lanview Leds
Recommended Action None. None. None. Ensure chassis has adequate power. None. If the LED remains amber for several minutes, contact Enterasys Networks for technical support. None. None. None. None. This state is activated when the OFFLINE/RESET switch is pressed for less than 1 second to start the process of an orderly shutdown. - Page 66 10/100 ports. Recommended Action None. None. None. Contact Enterasys Networks for technical support. If it is known that the port should be active and is not, contact Enterasys Networks for technical support. None. None, unless there is a high rate of activity.
-
Page 67: Troubleshooting Checklist
If the username/password combination has been password combination forgotten, refer to the section, entered. Switches,” set the mode switch to reset the username/ password combination to the default values. IP address not Refer to the Enterasys Matrix DFE-Gold Series assigned. - Page 68 Review the network design and delete unnecessary loops. If the problem continues, contact Enterasys Networks for technical support. Position of Mode switch Reenter the lost parameters as necessary. Refer (7), Persistent Data to the Enterasys Matrix DFE-Gold Series Reset, was changed...
-
Page 69: Overview Of Dfe-Gold Module Shutdown Procedure
You can shut down a DFE‐Gold module in an operating system using the OFFLINE/ RESET switch shown in Figure DFE‐Gold module. • Recommended shutdown procedure (page 4‐10) • Last resort shutdown procedure (not recommended) (page 4‐10) Figure 4-4 1 OFFLINE/RESET switch (in similar location on all modules) installed in a Matrix N3 or Matrix N7 chassis are interdependent 4‐4. There are two procedures to shut down a OFFLINE/RESET Switch Matrix DFE-Gold Series Modules Hardware Installation Guide 4-9 Overview of DFE-Gold Module Shutdown Procedure À... -
Page 70: Recommended Shutdown Procedure Using Offline/Reset Switch
Note: The only safe time to pull a DFE-Gold module out of the chassis is when the CPU LED is alternately flashing amber/off. Otherwise, system operation will be interrupted. Last Resort Shutdown Procedure Using OFFLINE/RESET Switch Caution: This method of shutting down a DFE module is not recommended except as a last resort, because all processes currently running on the module will be interrupted resulting in loss of frames. -
Page 71: Appendix A: Specifications
This appendix provides information about the following: • DFE‐Gold Module Specifications (page A‐1) • COM Port Pinout Assignments (page A‐3) • Regulatory Compliance (page A‐4) Enterasys Networks reserves the right to change the specifications at any time without notice. DFE-Gold Module Specifications Table A‐1 provides the I/O ports, processors and memory, physical, and environmental module specifications for DFE‐Gold modules, 4H4282‐49, 4H4283‐49, 4H4203‐72, 4H4202‐72, and 4H4284‐49. Unless noted differently, the specifications apply to all five DFE‐Gold modules. Table A-1 Specifications Item 4H4282-49 Ports 1 through 48 Option Slot 4H4283-49 Ports 1 through 48 Option Slot Specification Forty-eight, 10BASE-T/100BASE-TX compliant ports through 48, RJ45 connectors. - Page 72 DFE-Gold Module Specifications Table A-1 Specifications (continued) Item 4H4203-72 Ports 1 through 72 4H4202-72 Ports 1 through 72 4H4284-49 Ports 1 through 48 Option Slot Chassis Backplane Connectivity E7, N3, and N7 Chassis FTM Backplane Support Processors/Memory Processor Dynamic Random Access Memory (DRAM) FLASH Memory Physical...
-
Page 73: Com Port Pinout Assignments
Table A-1 Specifications (continued) Item Environmental Operating Temperature Storage Temperature Operating Relative Humidity COM Port Pinout Assignments The COM port is a serial communications port for local access to Local Management. Refer to Table Table A-2 COM Port Pin Assignments Signal Name Transmit Data (XMT) Clear to Send (CTS) Data Set Ready (DSR) Receive Data (RCV) Signal Ground (GND) Request to Send (RTS) Data Terminal Ready (DTR) -
Page 74: Regulatory Compliance
Regulatory Compliance Regulatory Compliance The 4H4282‐49, 4H4283‐49, 4H4203‐72, 4H4202‐72, 4H4284‐49, and 7G‐6MGBIC meet the safety and electromagnetic compatibility (EMC) requirements listed in Table Table A-3 Compliance Standards Regulatory Compliance Safety Electromagnetic Compatibility (EMC) A-4 Specifications Standards UL 60950, CSA C22.2 No. 60950, 2006/95/EC, EN 60950, IEC 60950, EN 60825, 21 CFR 1040.10. 47 CFR Parts 2 and 15, CSA C108.8, 2004/108/EC, EN 55022, EN 61000-3-2, EN 61000-3-3, EN 55024, AS/NZS CISPR 22, VCCI V-3. -
Page 75: Appendix B: Mode Switch Bank Settings And Optional Installations
Para realizar cualquiera de los procedimientos especificados en el apéndice, no olvide utilizar la pulsera electrostática que acompaña el chasis para minimizar los efectos de las descargas de electricidad estática. Mode Switch Bank Settings and Optional Installations Matrix DFE-Gold Series Modules Hardware Installation Guide B-1... -
Page 76: Setting The Mode Switches
Data on the next power‐up of the module. All user‐entered parameters, such as the IP address, module names, etc., are reset to the factory default settings. Once the module resets, you can either use the factory default settings or reenter your own parameters. • Switch 8 – Clear Admin Password. Changing the position of this switch clears the admin password, and restores the factory default password on the next power‐up of the module. Once the module resets, you can either use the factory default settings or reenter your own password. Note: Do not change the position of Switch 8 unless it is necessary to reset the admin password to its factory default setting. B-2 Mode Switch Bank Settings and Optional Installations B‐2 show the location of the mode switches and the switch settings ... -
Page 77: Mode Switch Location On 4H4282-49 And 4H4283-49
Figure B-1 Mode Switch Location on 4H4282-49 and 4H4283-49 1 Mode switch bank (located in same location on both the 4H4282-49 and 4H4283-49) Figure B-2 Mode Switch Location on 4H4203-72 À 1 Mode switch bank Matrix DFE-Gold Series Modules Hardware Installation Guide B-3 Setting the Mode Switches ➀... -
Page 78: Mode Switch Location On 4H4202-72
Setting the Mode Switches Figure B-3 1 Mode switch bank Figure B-4 1 Mode switch bank B-4 Mode Switch Bank Settings and Optional Installations Mode Switch Location on 4H4202-72 Mode Switch Location on 4H4284-49 ➀ 1 2 3 4 5 6 7 8... -
Page 79: Memory Locations And Replacement Procedures
Note: Because of the complexity of correctly replacing the large daughter board on the 4H4202-72, there is no procedure in this manual for replacing the DIMM on a 4H4202-72. Contact Enterasys Networks support or nearest representative if you need to replace the DIMM. -
Page 80: Dimm And Dram Simm Locations (4H4203-72
Memory Locations and Replacement Procedures Figure B-6 1 DRAM SIMM Figure B-7 1 DRAM SIMM B-6 Mode Switch Bank Settings and Optional Installations DIMM and DRAM SIMM Locations (4H4203-72) 2 DIMM DIMM and DRAM SIMM Locations (4H4202-72) 2 DIMM Á... -
Page 81: Dimm Replacement Procedure (4H4282-49 And 4H4283-49
DIMM Replacement Procedure (4H4282-49 and 4H4283-49) Caution: Observe all Electrostatic Discharge (ESD) precautions when handling sensitive electronic equipment. Precaución: Al trabajar con equipos electrónicos sensibles, tome todas las precauciones de seguridad para evitar descargas de electricidad estática. To remove and replace the DRAM SIMM on the 4H4282‐49 or 4H4283‐49, refer to Figure B‐8 and Figure Removing the DRAM SIMM Note: Prior to removing the DRAM SIMM in a 4H4282-49 or 4H4283-49, you must remove the Network Expansion Module to gain access to the DRAM SIMM memory and... -
Page 82: Removing The Existing Dram Simm From 4H4282-49 Or 4H4283-49
Precaución: Al trabajar con equipos electrónicos sensibles, tome todas las precauciones de seguridad para evitar descargas de electricidad estática. To install the memory module, refer to Figure With the connector arms set in the open position, insert the memory module between the connector fingers and push the memory module into the connector until the tabs on the two connector arms pull in towards the DRAM SIMM alignment notches. Push the DRAM SIMM further into the connector until the two alignment notches and the tabs on the two connector arms lock the DRAM SIMM into place. B-8 Mode Switch Bank Settings and Optional Installations B‐9. Push the connector arms away from the memory module to Removing the Existing DRAM SIMM from 4H4282-49 or 4H4283-49 À Â 2 Memory module Á À... - Page 83 Figure B-10 Installing the DRAM SIMM on 4H4282-49 1 Connector arms 2 DRAM SIMM memory module Removing the DRAM SIMM from 4H4203-72 Caution: Observe all Electrostatic Discharge (ESD) precautions when handling sensitive electronic equipment. Precaución: Al trabajar con equipos electrónicos sensibles, tome todas las precauciones de seguridad para evitar descargas de electricidad estática.
-
Page 84: Removing Existing Dram Simm From 4H4203-72
Precaución: Al trabajar con equipos electrónicos sensibles, tome todas las precauciones de seguridad para evitar descargas de electricidad estática. To install the DRAM SIMM, refer to Figure Push the connector arms away from the DRAM SIMM enough to insert the DRAM SIMM into the connector fingers. Insert the DRAM SIMM straight down between the connector fingers enough for the tabs on the connector arms to align with the two DRAM SIMM alignment notches. Push the DRAM SIMM down into the connector fingers. Then rotate the two connector arms toward the DRAM SIMM to lock it into place. B-10 Mode Switch Bank Settings and Optional Installations Removing Existing DRAM SIMM from 4H4203-72 Â À Á 2 Connector B‐12 and proceed as follows: À DRAM SIMM... -
Page 85: Dram Simm Replacement (4H4202-72
DRAM SIMM Replacement (4H4202-72) Note: Because of the complexity of correctly replacing the large daughter board on the 4H4202-72, it is recommended that you contact Enterasys Networks support or nearest representative if you need to replace the DRAM SIMM. Memory Locations and Replacement Procedures Ã... -
Page 86: Dimm Replacement Procedure (All Dfe Modules
To remove the existing DIMM, proceed as follows: Locate the DIMM connector on the main PC board. Refer back to Figure DIMM location on either the 4H4282‐49 or 4H4283‐49. Refer back to Figure location on the 4H4203‐72. Push the connector arms away from the DIMM, as shown in Figure simultaneously lift the DIMM enough to release it from the connector fingers. Figure B-13 1 Connector arms Rotate the DIMM upwards, then remove it from the connector fingers. B-12 Mode Switch Bank Settings and Optional Installations Removing the Existing DIMM À Â 2 DIMM B‐5 for the B‐6 for the B‐13, and Á À... -
Page 87: Installing The Dimm
Installing the DIMM Caution: Observe all Electrostatic Discharge (ESD) precautions when handling sensitive electronic equipment. Precaución: Al trabajar con equipos electrónicos sensibles, tome todas las precauciones de seguridad para evitar descargas de electricidad estática. To install a DIMM, refer to Figure Insert the DIMM down between the connector fingers. Pivot the DIMM downward so the tabs on the connector arms align with the two DIMM alignment notches. With the two connector arms spread outward, push the DIMM down between the connector arms. Then release the two connector arms to lock the DIMM into place. Figure B-14 Installing the DIMM 1 DIMM... - Page 88 Memory Locations and Replacement Procedures B-14 Mode Switch Bank Settings and Optional Installations...
- Page 89 Numerics 100BASE-FX connections 3-18 requirements 100BASE-TX connections 3-11 requirements 10BASE-T connections 3-11, 3-15 requirements 4H4202-72 introduction to 4H4203-72 introduction to 4H4282-49 introduction to 4H4283-49 introduction to 4H4284-49 introduction to Cable connections 4H4282-49 or 4H4202-72 3-11 4H4283-49 or 4H4203-72 3-15 4H4284-49 3-18 Cable specifications 100BASE-FX network...
- Page 90 Matrix N3 chassis module installation into Matrix N5 chassis module installation into Memory replacement of DRAM B-12 Memory locations DIMM and SIMM Mode Switch setting of Module features 1-2, Network connecting to 3-10 Network expansion module Network Requirements list of...