Advertisement
Available languages
Available languages
The relnote control can perform the following functions:
• Turn the system ON and OFF
• Select operating mode
• Adjust room air temperature and tan speed
• Set time periods for automatic system operation
BATTERY INSTALLATION
Two AAA
1.5V alkaline
batteries (included) are required for operation of the relnote
control. See Fig. 2 for battery location.
To install batteries:
1. Remove battery compartlnent cover by sliding off of
relnote.
2. Insert batteries being sure to follow polmity markings in-
side battery compartlnent.
3. Replace battery compartlnent cover.
NOTE: Replace batteries whenever "Low battery" iMicator
appears on remote control display panel.
DISPLAY SCREEN
There are five operating mode indica-
tors that appear on the rcnnote control display screen. See Fig. 3.
OPERATION
Remote
Control
Operation--
The remote
control
has 3 buttons (see Fig. 4) used for operating and controlling the
system:
• MODE button
changes operating mode
• UP/DOWN button
selects desired operating mode
• ON/OFF button
turns the system on or off and trans-
mits programing selections to unit.
BACK OF
REMOTE
CONTROL
2 AAA 1,5V BATTERIES
BATTERY
COMPARTMENT
COVER
Fig. 2 -- Location
of Batteries
on Remote Control
COOLING
FAN ONLY
\\1 I//
HEATING
83
DEHUMIDIFICATION
AUTO
Fig. 3 -- Operating
Mode Indicators on
Remote Control
NOTE: When transmitting a colrnnand fiom the controller to
the unit, be sure to point the controller toward the right side of
the unit. See Fig. 4. The unit will confirm receipt of a com-
mand by sounding 2 audible beeps.
IMPORTANT: If no changes are made within 10 sec-
]
onds, the remote control will remm to its previous
I
setting.
FAN SPEED
To select the Fan mode and change the Fan
Speed, follow the steps below:
1. Press MODE button to select the Fan mode.
2. Press UP/DOWN button to select desired tan speed or
to Auto.
3. Press ON/OFF button to send changes to unit from re-
mote control.
NOTE: If unit is operating in DEtRIMIDIFICATION
mode
the l_anwill only operate in Low speed and cannot be changed.
TEMPERATURE SETTINGS
The temperature
settings
can be easily changed by pointing the controller toward the unit
and pressing the UP/DOWN button until desired temperature
appears on screen. The _' symbol appears each time the ON/
OFF button is pressed.
Another way of changing the temperature is as follows:
1. Select the temperature display by pressing the MODE
button. The degee symbol will flash next to the digits on
the screen.
2. Press UP/DOW2"_button to select the desired tempera-
ture. The available temperature range is fiom 54 F to
90 F.
3. Press ON/OFF button to send changes to unit fiom re-
mote control.
AIRFLOW DIRECTION
Perform the following steps to
change the direction of airflow from the unit:
1. Press MODE button to select the Sweep fanction.
2. Press the top of the UP/DOWN button to move the air
deflector on the unit in an up and do,a_ motion. The air-
flow symbol displays motion.
3. Press the bottom of the UP/DOWN button. The airflow
deflector stops at a given angle. The airflow symbol dis-
play remains in a fixed position.
4. Press ON/OFF button to seM changes to unit fiom re-
mote control.
NOTE: If placing the air deflector in a fixed position is chosen,
the deflector stops at the angle in which it was located when
the ON/OFF button was pressed.
SETTING CLOCK
1. Slide down fiont cover of controller below ON/OFF but-
ton. See Fig. 4.
2. Press CLOCK button using the tip of a pen or paper clip.
See Fig. 5.
3. Press UP/DOWN button to set minutes.
4. Press MODE button. The hour digits will flash.
5. Press to UP/DOWN button to set the hour.
6. To confirm cunent clock settings, press CLOCK button
once again using the tip of a pen or paper clip. The remote
control will automatically go back to previous display
and the clock is displayed.
Advertisement
