Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Viper Viper 125HF
Summary of Contents for Viper Viper 125HF
- Page 1 MODEL 125 HF OWNER'S GUIDE 03/00 and up...
-
Page 2: Limited Lifetime Consumer Warranty
Contact your authorized dealer to obtain the ser- vice charge for your unit. These systems are a deterrent against possible theft. Directed Electronics, Inc. is not offering a guarantee or insuring against the theft of the automobile or its contents and disclaims any liability for the theft of the vehicle and/or its contents. - Page 3 This product warranty is automatically void if its date code or serial number is defaced, missing, or altered. This warranty will not be valid unless you have com- pleted the warranty card and mailed it to Directed Electronics, Inc. within 10 days after purchase to the address listed on the warranty registration card.
-
Page 4: Table Of Contents
......... 14 1999 Directed Electronics, Inc. - Page 5 Standard Configuration 1999 Directed Electronics, Inc. ©...
-
Page 6: What Is Included
The system requires no specific maintenance. Your remote is pow- ered by a miniature 12V battery, type GP23A, that lasts approxi- mately one year under normal use. When the battery weakens, the LED on the remote will dim and operating range will be reduced. 1999 Directed Electronics, Inc. ©... -
Page 7: Your Warranty
Caution This product is designed for fuel injected, automatic transmission vehicles only. Use of this product in a standard transmission vehi- cle is dangerous and contrary the product's intended use. 1999 Directed Electronics, Inc. ©... -
Page 8: Transmitter Functions
Button I The door locking and unlocking functions are controlled by press- Button II Timer Mode is controlled by Button I and II The remote start function of your system is controlled by pressing simultaneously. 1999 Directed Electronics, Inc. ©... -
Page 9: Using Your System
STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED. These precautions are the sole responsibility of the user. Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, 1999 Directed Electronics, Inc. ©... - Page 10 OF THE UNIT AND SEEK THE ASSISTANCE OF AN AUTHORIZED DEI DEALER TO REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DEI WILL NOT BE HELD RESPONSI- BLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS. 1999 Directed Electronics, Inc. ©...
-
Page 11: Locking
NOTE: If the ignition is turned on while the vehicle is remote started the doors will not lock until the remote start shuts off. To avoid being locked out of the vehicle, do not turn the ignition on until you are ready to drive the vehicle. 1999 Directed Electronics, Inc. ©... -
Page 12: Remote Start
Insert the ignition key and turn it to the ON (not the START) position. Press the brake pedal. NOTE: If the brake pedal is pressed before the key is in the ON position, the engine will shut down. 1999 Directed Electronics, Inc. ©... -
Page 13: Timer Mode
IMPORTANT! This feature must only be used in open areas, never in an enclosed area such as a garage. To enter Timer Mode: Start the vehicle by pressing and releasing Press and release Within two seconds press and release again. 1999 Directed Electronics, Inc. ©... -
Page 14: Valet Take-Over
This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would like to leave the motor running and the climate controls on. 1999 Directed Electronics, Inc. ©... -
Page 15: Using Remote Start With Factory Remote Systems
Spaces are provided below for writing in the button and number of button presses. OEM transmitter button used for Remote Start/Valet Take-Over sequence____________________________________________ Number of presses required to initiate Remote Start/Valet Take-Over sequence___________________________________ 1999 Directed Electronics, Inc. ©... -
Page 16: Programming Options
It houses the microprocessor which monitors your vehicle and controls all the system functions. Transmitter: A hand-held, remote control which operates the var- ious functions of your system. 1999 Directed Electronics, Inc. ©... -
Page 17: Quick Reference Guide
Start/Valet Take-Over sequence can be programmed to initiate with one to three (1-3) presses of one of the OEM transmitter buttons. OEM transmitter button used for Remote Start/Valet Take-Over sequence______________________________________________ Number of OEM transmitter button presses required to initiate Remote Start/Valet Take-Over sequence____________________ 1999 Directed Electronics, Inc. ©... - Page 18 20 patents in the field of advanced electronic technology, DEI is ISO 9001 registered. Quality Directed Electronics products are sold and serviced throughout North America and around the world. Call (800) 274-0200 for more information about our products and services.