Table of Contents
Advertisement
TRENDnet User's Guide
Technical Specifications
Hardware
IEEE 802.3, IEEE 802.3u, IEEE 802.1Q, IEEE 802.1p, IEEE 802.11b, IEEE
802.11g, based on IEEE 802.11n technology
Complies with ADSL standards:
Standards
-ANSI T1.413 Issue2, G.992.1 (G.dmt, Annex A), G.992.2 (G.lite)
Complies with ADSL2 standard: G.992.3 (G.dmt.bis, Annex L)
Complies with ADSL2+ standard: G.992.5 (G.dmt.bis+, Annex M)
WAN (ADSL Line Interface)
1 x RJ-11 port (telephone)
4 x 10/100 Mbps Auto-MDIX RJ-45 ports (option to convert port 1 to WAN
LAN
port)
Reset: Reset to factory defaults (Hold for 15 sec.)
Reset / WPS / WLAN On & Off
WPS: Activates Wi-Fi Protected Setup (WPS) (Hold for 3 sec.)
Button
WLAN On / Off: Enables or disables wireless radio (Hold for 10 sec.)
VC and LLC multiplexing (Up to 8 PVCs), Ethernet over ATM (RFC 1483
Bridged) with NAT, RFC 1483 bridged, IP over ATM (RFC 1483 Routed), PPP
ATM & PPP Protocols / Modes
over ATM (RFC2364), PPP over Ethernet (RFC2516), ATM Traffic QoS (UBR,
CBR, VBR, GFR)
NAT, SPI, DMZ host, virtual servers, MAC / IP filters, URL / keyword filters,
Firewall
deny WAN ping requests, and WAN stealth mode
Schedules
Define schedules for wireless, virtual server, packet filters, and QoS
IGMP v1/2/3 proxy and snooping , Static and dynamic routing RIP v1/2,
UPnP, DHCP (Dynamic Host Configuration Protocol) server/relay, Dynamic
DNS (DynDNS.com, No-IP.com, TZO.com, and dhs.org), NTP (Network Time
Network Protocols/Features
Protocol), PPTP / L2TP / IPsec VPN pass through, IPv6: Static, DHCPv6,
PPPoE, 6 to 4, and IPv6 in IPv4 Tunnel, Stateful / Stateless auto-
configuration
Smart-QoS (simple) or manually defined QoS ToS / CoS (Type of service /
Quality of Service
Class of service) based on IP, TCP/UDP port, MAC, DSCP (Differentiated
Services Code Point), and WMM
Local / remote configuration, upgrade firmware, backup / restore
configuration via web browser, TR-069 remote management, DoS (Denial of
Management / Monitoring
Service) detection, internal system log, Syslog, email alert, SNMP v1/v2c,
ping test tool, and Wake-on-LAN (WoL), NAT Status log, Client List log, Web
log, Modem log
LED Indicators
Status, ADSL, WLAN, LAN1~LAN4
Power Adapter
Input: 100~240V AC, 50~60Hz, 0.2A
© Copyright 2013 TRENDnet. All Rights Reserved.
Output: 5V DC, 1.2A external power adapter
Power Consumption
5 watts (max)
Dimension (L x W x H)
189 x 118 x 33 mm (7.4 x 4.6 x 1.3 in.)
Weight
221.1 g (7.8 oz)
Operation: 0° ~ 40°C (32°F ~ 104°F)
Temperature
Storage: -10° ~ 70°C (14°F ~ 158°F)
Humidity
Max. 95% (non-condensing)
Certifications
CE, FCC
Wireless
Frequency
2.4 ~2.483GHz band
Modulation
DBPSK / DQPSK / CCK / OFDM (BPSK / QPSK / 16-QAM / 64-QAM)
Access Point Router, Access Point Only, WDS Hybrid, WDS Only, Universal
Modes
Repeater
Broadcast up to 2 SSIDs each with different wireless encryption with support
SSID
for VLAN mapping
Antenna
1 x 2 dBi detachable dipole antenna
802.11b: up to 11 Mbps
Data Rate
802.11g: up to 54 Mbps
802.11n: up to 150 Mbps
WEP (HEX/ASCII): 64/128-bit
Security
WPA (AES/TKIP): WPA / WPA2-RADIUS, WPA-PSK / WPA2-PSK
802.11b: 17 dBm (typical)
Output Power
802.11g: 14 dBm (typical)
802.11n: 14 dBm (typical)
802.11b: -91 dBm (typical) @ 11 Mbps
Receiving Sensitivity
802.11g: -91 dBm (typical) @ 54 Mbps
802.11n: -87 dBm (typical) @ 150 Mbps
Channels
1~ 11 (FCC), 1~13 (ETSI)
*Maximum wireless signal rates are referenced from IEEE 802.11 theoretical specifications. Actual
data throughput and coverage will vary depending on interference, network traffic, building
materials and other conditions.
TEW-718BRM
63
Advertisement
Table of Contents
