Setting menu items
(Continued)
z INCOM/MIC Screen
z
This menu is used for the unit's intercom settings .
Configure the camera's intercom setting on the camera .
Moving the cursor to the "INCOM/MIC" menu title and then pressing the
SELECT dial redisplays the OPERATION menu one level up .
INCOM/MIC
4 W /RTS IN LEVEL
4 W /RTS OUT LEVEL
R T S CANCEL
G A IN PGM
M I C1 LEVEL
M I C2 LEVEL
C M /DM
C C U INCOM MIC
C C U SIDE TONE
indicates the factory default setting .
Setting
Item
value
4W/RTS
–40 .0dB
IN LEVEL
│
0dB
│
20 .0dB
4W/RTS
–40 .0dB
OUT LEVEL
│
0dB
│
20 .0dB
RTS CANCEL
–40 .0dB
│
31 .5dB
GAIN PGM
0dB
20dB
MIC1 LEVEL
–40 .0dB
│
0dB
│
20 .0dB
MIC2 LEVEL
–40 .0dB
│
0dB
│
20 .0dB
CM/DM
CM
DM
CCU INCOM MIC
–40 .0dB
│
0dB
│
12 .0dB
CCU SIDE TONE
–40 .0dB
│
–6dB
│
0 .0dB
0dB
0dB
0dB
0dB
0dB
0dB
DM
0dB
–6dB
Remarks
Set the input level for the intercom
(4-WIRE and RTS) signal .
(0 .5dB increments)
Set the output level for the intercom
(4-WIRE and RTS) signal .
(0 .5dB increments)
Set the noise canceling level for the
engineering intercom (RTS system) .
(0 .5dB increments)
Set the gain for the PGM sound .
Finely adjust the level of output from the
MIC OUT 1 connector .
(0 .5dB increments)
Finely adjust the level of output from the
MIC OUT 2 connector .
(0 .5dB increments)
Use this to select the type of intercom
microphone (carbon microphone or
dynamic microphone) to be connected
to the unit .
CM: Carbon microphone
DM: Dynamic microphone
Use this to set the level of the unit's
intercom microphones for regular use .
(0 .5dB increments)
Use this to set the side tone level of the
unit's intercom for regular use .
(0 .5dB increments)
MAINTENANCE Menu
This is the selection screen for the MAINTENANCE menu .
Moving the cursor to the "MAINTENANCE" menu title and then pressing
the SELECT dial redisplays "TOP MENU" .
MAI NTEN ANC E
STA RT UP
ANA LOG GAI N
ND NAM E
NET WOR K
VER SIO N
PM VIE W SE TTI NG
PM OPE RATI ON STA TUS
SYS TEM
SD CAR D
z START UP
z
Displays the screen for setting the control to be performed when the
unit's power has been turned on .
z ANALOG GAIN
z
Displays the screen for setting the analog signal levels .
z ND NAME
z
Displays the screen for setting the ND filter names .
z NETWORK
z
Displays the network setting screen .
z VERSION
z
Displays the version information screen .
z PM VIEW SETTING
z
Displays the screen for setting ON or OFF for the items (IRIS and
status displays) to display on the picture monitor .
z PM OPERATION STATUS
z
Displays the screen for setting ON or OFF for the operation items to
display on the picture monitor .
z SYSTEM
z
Displays the screen for initializing the menu settings .
z SD CARD
z
Displays the screen for setting the saving of data and upgrading of
software using a memory card .
21