Denon AVR-A100 Owner's Manual page 92

ENGLISH
Setting items
Height Gain Low : Reduce the front height channel volume.
Control the front height Mid : Front height channel sound is output with standard sound volume.
channel volume. High : Increase the front height channel volume.
NOTE
"Height Gain" is displayed for the following settings.
• When the "Speaker Config." – "Front Height" setting (vpage 96) is set
other than to "None".
• When surround mode is "PLgz" or the PLgz decoder is used.
PLgz Height ON : Audio is output from the front height speaker.
Determine whether to use OFF : Audio is not output from the front height speaker.
front height channel.
NOTE
• "PLgz Height" is displayed with the settings listed below.
• When the "Speaker Config." – "Front Height" setting (vpage 96) is
set to other than "None".
• "PLgz Height" cannot be set if the HD Audio source being played
includes a front height channel. In this case, the Front height channel
is played back without decoding in PLgz mode, using the input signal.
Height/Wide : Sound is output from the front height speakers and front
Speaker
Make settings for the wide speakers.
speakers outputting sound Height : Sound is output from the front height speakers.
when playing back in Wide : Sound is output from the front wide speakers.
DENON original surround OFF : Sound is not output from the front wide speakers and front height
mode. speakers.
NOTE
Only speakers that are set to something other than "None" in "Speaker
Config." (vpage 95) can be selected.
ON : Set.
Subwoofer Att.
Attenuate subwoofer level OFF : Do not set. Usually use in this mode.
when using EXT. IN input.
Set this to "ON" if the subwoofer channel level seems too high when
playing audio signal.
Subwoofer ON : The subwoofer is used.
Turn subwoofer output on OFF : The subwoofer is not used.
and off.
NOTE
This can be set when the surround mode is "DIRECT" (vpage 52) and the
"Subwoofer Mode" (vpage 96) is "LFE+Main".
ON : Create a wider sound stage.
Effect
Switch effect signal for OFF : The effect is not set.
multi-surround speakers on
and off.
88
Remote control operation
buttons
Setting details
Move the cursor
(Up/Down/Left/Right)
Setting items
Effect Level 1 – 15 (10)
Adjust effect signal level.
Set to a lower level if the positioning and sense of phase of the
surround signals seems unnatural.
Room Size Medium : Simulate acoustics of a medium room.
Determine size of acoustic Medium-large : Simulate acoustics of a medium-large room.
environment. Large : Simulate acoustics of a large room.
Small : Simulate acoustics of a small room.
Medium-small : Simulate acoustics of a medium-small room.
NOTE
"Room Size" does not indicate the size of the room in which sources are
played.
Yes : Reset to the defaults.
Default
The "Surround Parameters" No : Do not reset to the defaults.
settings are returned to the
default settings.
n Tone
Adjust the tonal quality of the sound.
Setting items
Tone Control ON : Allow tone adjustment (bass, treble).
Set the tone control function OFF : Playback without tone adjustment.
to ON and OFF.
"Tone Control" can be set when "Dynamic EQ" (vpage 89) and
"Dolby Volume" (vpage 91) are set to "OFF".
NOTE
• "Tone Control" settings are not reflected to ZONE2 and ZONE3.
• The tone cannot be adjusted in the direct mode.
Bass –6dB – +6dB
Adjust low frequency range
"Bass" can be set when "Tone Control" is set to "ON".
(bass).
Treble –6dB – +6dB
Adjust high frequency range
"Treble" can be set when "Tone Control" is set to "ON".
(treble).
Confirm the setting
AUDIO/VIDEO ADJUST
Setting details
Setting details
Return to previous menu