Denon AVR-A100 Owner's Manual page 68

ENGLISH
Front B Select the Front B setting to use
the second set of front speakers
for playback. In this case, go to
step 5.
11CH Select the 11CH
perform playback using up to 11.2
channels using a combination of
the unit's built-in power amplifi er
for 9-channel and an external
power amplifi er for 2-channel. In
this case, go to step 6.
PRE AMP Select the PRE AMP setting to
use this unit as a preamplifi er
by connecting all speakers to an
external power amplifi er. You
can perform up to 11.2-channel
playback. In this case, go to step
7.
5
Use i to select "Assign Sp.", and
use to select a speaker for audio
o p
output assigned by "Amp Assign".
S.BACK Select the S.BACK setting to
output the assigned audio from
the surround back speakers.
F.HEIGHT
Select the F.HEIGHT setting to
output the assigned audio from
the front height speakers.
F.WIDE Select the F.WIDE setting to
output the assigned audio from
the front wide speakers.
6
Use to select "Ext. Amp", and
i
use to select the PRE OUT
o p
connector to which an external
power amplifi er is connected.
Height
Select the Height setting to
connect an external
amplifi er to the front height (FHL/
FHR) terminals of PRE OUT
connector for playback.
Front Select the Front setting to connect
an external power amplifi er to the
front (FL/FR) terminals of PRE
OUT connector for playback.
64
Remote control operation
buttons
7
Use to select "Assign Sp.", and use
i
to set whether or not to use the
o p
speaker terminals for multizone.
None
Select the None setting when you
setting to
do not want to use the speaker
terminals for multizone.
ZONE2/3 Select the ZONE2/3 setting when
you want to use the speaker
terminals for multizone.
8
Press RETURN to exit the "Amp
Assign" setting.
9
Set up "Channel Select"
Use ui to select "Channel Select",
and then press ENTER
AUDYSSEY AUTO SETUP
STEP1 Preparation
Connect the speakers and place them according
to the recommendations in the manual,
Set the following items
If necessary.
Amp Assign
Channel Select
Auto Setup Start
Enter
Enable skip of measuring unused channels to reduce time
AUDYSSEY AUTO SETUP
Channel Select
STEP1 Preparation
Subwoofer Measure (1 spkr)
Connect the speakers and place them according
to the recommen Measure n the manual,
Surround Back Measure (2 spkrs)
Set the following items
Front Height Measure
If necessary.
Amp Assign
Channel Select
Measure subwoofer channel (1 speaker)
Auto Setup Start
power
Enter
Enter
Enable skip of measuring unused channels to reduce time
Move the cursor
(Up/Down/Left/Right)
10
Use to select a channel.
ui
Front Select for setting the front speakers
to be used. In this case, go to step
11.
• "Front" can be set when "Assign
Mode" is set to "Front B".
Subwoofer Select the number of subwoofers to
be used. In this case, go to step 12.
Surround
Select the number of surround back
Back
speakers to be used. In this case, go
to step 13.
• "Surround Back" cannot be set
when "Amp Assign" – "Assign
Mode" is set to "ZONE2/3" or
when "Assign Sp." is set to
.
"S.BACK".
Front
Select for no front height speakers
Height
to be used. In this case, go to step
1 2 3 4 5 6
14.
• "Front Height" cannot be set
when "Amp Assign" – "Assign
Mode" is set to "ZONE2/3", "2CH
Bi-AMP" or when "Assign Sp." is
set to "F.HEIGHT".
Cancel
RETURN Select for no front wide speakers to
Front Wide
be used. In this case, go to step 14.
• "Front Wide" cannot be set when
"Amp Assign" – "Assign Mode" is
set to "ZONE2/3", "2CH Bi-AMP"
or when "Assign Sp." is set to
"F.WIDE".
1 2 3 4 5 6
11
Press to select a front speaker.
o p
A Select this to use front speaker A.
B
Select this to use front speaker B.
Cancel
A+B Select this to use front speakers A and B
RETURN Cancel
RETURN
simultaneously.
Confi rm the setting
Set up speakers
12
Use to set whether or not a
o p
subwoofer channel is measured.
Measure
Set for measuring two subwoofers
(2 spkrs)
(multiple subwoofe calibration).
Set for measuring a subwoofer.
Measure
(1 spkr)
Skip Set for no measuring of a subwoofer.
• When using two subwoofers, please select
"Measure (2 spkrs)".
13
Use to set whether or not a
o p
surround back channel is measured.
Set for measuring two surround back
Measure
(2 spkrs) speakers.
Set for measuring a surround back
Measure
(1 spkr) speaker.
Set for no measuring of a surround
Skip
back speaker.
14
Use to set whether or not front
o p
height and front wide channels are
measured.
Measure Set to measure the front height
speakers or front wide speakers.
Skip
Set when you do not want to measure
the front height speakers or front wide
speakers.
15
Press ENTER .
Proceed to page 9 STEP1 Preparation
step 6.
NOTE
After performing Audyssey ® Auto Setup, do not
change the speaker connections or subwoofer
volume. In event of a change, perform Audyssey
Auto Setup again.
Return to previous menu