Denon AVR-A100 Owner's Manual page 114

ENGLISH
8
The procedures for registering remote control codes
and remote control preset registration are displayed.
REMOTE PRESET CODES
OPTION
Category : DVD
Brand : Denon
Code [ 1/ 4] : 30490
1. Press and hold 3sec.both[POWER ON][DEVICE ON]
button."PRSET" is displayed on remote.
2. Press [ENTER] button. "MODE?"is displayed on remote.
3. Press [Input Souce] button.
4. Input Code with [0-9] button.
5. Press any key to check device. (e.g. [DEVICE ON])
OK NG
QUICK1 QUICK2
Press QUICK1 if device works, QUICK2 if not
NOTE
If a wrong brand name is selected, press
following screen is displayed:
REMOTE PRESET CODES
OPTION
Category : TV
Press[AMP] button.
Brand : Sanyo
And press [ENTER] button to return
Code [ 1/ 3]
: 11037
Bland select menu.
1. Press [INPUT SOURCE] button.
button
2. Press and hold 3sec. both [POWER ON]
3. Press
4. Input with [0-9] button.
5. Press any key to check device. O K
OK NG
QUICK1 QUICK2
Press QUICK1 if device works, QUICK2 if not
AMP ENTER
Press then to return to step 7.
9
Hold POWER ON and ZONE/DEVICE ON
simultaneously for more than 3 seconds.
"SETUP" fl ashes twice on the remote control unit.
10
When "PRSET" appears on the remote control unit,
ENTER
press .
11
When "MODE?" appears on the remote control
unit, press the input source select button of the AV
equipment ( DVD , BD , SAT/CBL
GAME CD TV
, or ) that you want to program for the
preset setting.
TV
• For , only the preset code for the categories "TV", "TV/DVD" or
"TV/VCR" can be registered.
110
Remote control operation
buttons
12
When "– – – – –" appears on the remote control unit,
press the number buttons
Press the buttons with an interval less than 30 seconds.
Return
QUICK3
• When the code is registered.
QUICK SELECT 3
. The
"SET" fl ashes four times on the remote control unit.
• When the code is not registered correctly
"NG" fl ashes four times on the remote control unit.
Perform from step 9 again.
• When an input number is not correct
POWER ON
Press
9 again.
13
Operate the device being used to check the operation.
• If the device is operating, press
Go to step 14.
Return
QUICK1
• If the device is not operating, press
Go to step 15.
14
The screen shown below is displayed, and registration
pressed
of the preset code is completed.
, DVR , DOCK , V.AUX ,
• The menu screen is retrieved. Press
Move the cursor
(Up/Down/Left/Right)
0 – 9 to enter a 5-digit code.
REMOTE PRESET CODES
OPTION
Category : DVD
Brand : Denon
Code [ 1/ 4] : 30490
1. Press and hold 3sec.both[POWER ON][DEVICE ON]
button."PRSET" is displayed on remote.
2. Press [ENTER] button. "MODE?"is displayed on remote.
3. Press [Input Souce] button.
4. Input Code with [0-9] button.
5. Press any key to check device. (e.g. [DEVICE ON])
OK NG Return
QUICK1 QUICK2 QUICK3
Press QUICK1 if device works, QUICK2 if not
once then perform the operations from step
QUICK SELECT 1
.
QUICK SELECT 2
.
REMOTE PRESET CODES
OPTION
Category : TV
Brand : Sanyo
Remote Preset Codes setup is finished.
Code [ 1/ 3] : 11037
Press[AMP] button.
1. Press [INPUT SOURCE] button.
And press [ENTER] button to return
2. Press and hold 3sec. both [POWER ON]
MENU.
button.
3. Input Code with [0-9] button.
O K
4. Press any key to check device.
(e.g. [DEVICE ON])
OK NG Return
QUICK1 QUICK2 QUICK1
Press QUICK1 if device works, QUICK2 if not
AMP ENTER
then .
Confi rm the setting
Operating the main remote control unit
15
Either of the screens below is displayed.
q
REMOTE PRESET CODES
OPTION
Category : TV
Brand : Sanyo
Code [ 1/ 3]
: 11037
Selected code is not matched.
1. Press [INPUT SOURCE] button.
2. Press and hold 3sec. both [POWER ON]
Plesse try other codes.
button.
3. Input Code with [0-9] button.
4. Press any key to check device.
(e.g. [DEVICE ON])
OK NG
QUICK1 QUICK2 QUICK1
Press QUICK1 if device works, QUICK2 if not
• The screen is displayed for 3 seconds, then the next preset
registration screen is displayed automatically.
w
REMOTE PRESET CODES
OPTION
Category : TV
Brand : Sanyo
Sorry, your remote is not supported.
Code [ 1/ 3] : 11037
This function can not be used for
your device.
1. Press [INPUT SOURCE] button.
2. Press and hold 3sec. both [POWER ON]
Press[AMP] button.
button.
And press[ENTER] button to return
3. Input Code with [0-9] button.
MENU.
O K
4. Press any key to check device.
(e.g. [DEVICE ON])
OK NG
QUICK1 QUICK2 QUICK1
Press QUICK1 if device works, QUICK2 if not
GIf screen q is displayedH
The device may be operating with the preset code displayed next.
The preset registration screen is displayed. Repeat steps 9 to 13.
GIf screen w is displayedH
The device cannot be controlled with the remote control unit supplied
with this unit. Use the remote control unit supplied with the device
to be used. The menu screen is retrieved. Press
Some manufacturers use more than one type of remote control code.
Preset codes to change the number and verify correct operation.
NOTE
Depending on the model and year of manufacture of your equipment,
some buttons may not operate.
Return to previous menu
Return
Return
AMP ENTER
then .