Setting The Speakers (Speaker Setup); Setting The Subwoofer Output (Sw Channel) - Alpine PXA-H800 Owner’s Manual

From the Commander
1
* When you modify the "FRONT HIGH" speaker setting to [Full], a
message to confirm the change will be displayed. To set up at "Full
Range," rotate the [Rotary encoder] to select "OK", and then press
the [Rotary encoder]. Make sure the speaker being used for this
output is able to handle a full range source. Many tweeters can be
damaged when driven by a full range signal.
2
* This item is enabled for setup only when 2 subwoofers are connected.
Rotate the [Rotary encoder] to select "Stereo" or "Mono", and then
press the [Rotary encoder].
Stereo: Subwoofer stereo (L/R) output
Mono: Subwoofer monaural output
• Speakers that cannot be turned off are disabled for setup. Refer to
Table 1 (Output System) in "System Configuration" (page 60).
• When you connect just one subwoofer, turn off "Subwoofer2. "
7-1
First time start-up:
The AUX Input System Select screen will be
automatically displayed. Continue to set, referring to
"Setting the AUX Input System (AUX Input Setup)"
(page 39).
7-2
Subsequent start-up:
The "Turn ACC Off" screen will be displayed. Turn the
ignition key to off and then on again. The settings
become effective.
• If [ ] is pressed during setting, the unit returns to the previous
item.
• If the speaker system is changed, all setup values except those for
AUX input will be restored to the initial setup values.
• You can also set the speakers from "Setting the Speakers (Speaker
Setup)" (page 38).
• You can also set the subwoofer output from "Setting the Subwoofer
Output (SW Channel)" (page 38).
• After the setting, it is recommended to store the setting contents on
the unit. For details, refer to "Storing the Preset Values (Preset
Store)" (page 36).

Setting the Speakers (Speaker Setup)

Turn on the connected speakers.
1
Press [FUNC.].
2
Rotate the [Rotary encoder] to select "Output
Setup," and then press the [Rotary encoder].
3
Rotate the [Rotary encoder] to select "Speaker
Setup," and then press the [Rotary encoder].
The Speaker selection screen is displayed.
4
Rotate the [Rotary encoder] to select the speaker to
be set, and then press the [Rotary encoder].
Setting contents: Front High/Front Mid/Front Low/Rear/
Center/Subwoofer (1, 2)
• Speakers to be set vary depending on the system set in "Setting the
Speaker System (System Select)" (page 37).
• Speakers that cannot be turned off are disabled for setup. Refer to
Table 1 (Output System) in "System Configuration" (page 60).
38
-EN
5
Rotate the [Rotary encoder] to select "ON" or "OFF,"
etc., and then press the [Rotary encoder].
Repeat the steps until all the speakers are set.
Front High*: OFF/Tweeter/Full
Front Low: OFF/ON
Rear: OFF/ON
Center: OFF/ON
Subwoofer(1, 2): OFF/ON
* When you modify the "Front High" speaker setting to [Full], a
message to confirm the change will be displayed. To set up at "Full
Range," rotate the [Rotary encoder] to select "OK", and then press
the [Rotary encoder]. Make sure the speaker being used for this
output is able to handle a full range source. Many tweeters can be
damaged when driven by a full range signal.
• When you connect just one subwoofer, turn off "Subwoofer2."
6
To set up other speakers, press [
Steps 4 and 5.
7
When the setting is complete, press and hold [
for at least 2 seconds.
• If [ ] is pressed during setting, the unit returns to the previous
item.
• When the speaker setting is changed while ImprintEQ/RoadEQ is on,
ImprintEQ/RoadEQ will be turned off after a confirmation message
is displayed.
• After the setting, it is recommended to store the setting contents on
the unit. For details, refer to "Storing the Preset Values (Preset
Store)" (page 36).
Setting the Subwoofer Output (SW
Channel)
You can set the subwoofer output to stereo or monaural. Make sure to
set the correct output for your subwoofer type. (Initial Setting: "Mono")
1
Press [FUNC.].
2
Rotate the [Rotary encoder] to select "Output
Setup," and then press the [Rotary encoder].
3
Rotate the [Rotary encoder] to select "SW Channel,"
and then press the [Rotary encoder].
The Subwoofer Channel selection screen is displayed.
4
Rotate the [Rotary encoder] to select "Mono" or
"Stereo," and then press the [Rotary encoder].
Mono: Subwoofer monaural output
Stereo: Subwoofer stereo (L/R) output
] and repeat
]