Warranty Information; Regulatory Information - Oki MPS5500mb Safety And Regulatory Information Manual

Regulatory Information

ENERGY STAR
As an ENERGY STAR Partner, Oki Data has
determined that this product meets the
ENERGY STAR guidelines for energy
efficiency.
Year 2000 Compliance
This product is Year 2000 Compliant. It contains
information technology that accurately processes date and
time data between the years 1999 and 2000, and carries
no issue for the September 9, 1999 (9999) programming
concern. This product, when used in combination with
products purchased from other manufacturers, whose
products properly exchange data and time information, will
accurately process the date and time.
FCC Radio Frequency Interference Statement
WARNING: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference
in a commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at their own expense.
Note: It is the responsibility of the user to obtain the
required shielded cable in order to ensure
compliance of this equipment with FCC regulations.
Changes or modifications not expressly approved by Oki
Data may void your authority to operate this device.
FCC Administrative Council for Terminal
Attachment Requirements for End Users
This device has been granted a registration number by the
Administrative Council for Terminal Attachment (ACTA),
under Part 68 and ACTA rules and regulations for direct
connection to the telephone lines. In order to comply with
these FCC rules, the following instructions must be
carefully read and applicable portions followed completely.
1. This equipment complies with Part 68 of FCC rules and
the requirements adopted by the ACTA. On the back of
the equipment is a label that contains, among other
information, a product identifier in the format
US:AAAEQ##TXXXX. If requested, this inf
2. The following USOC jacks may be used with this
equipment: RJ11C.
3. A plug and jack used to connect this equipment to the
premises wiring and telephone network must comply
with the applicable FCC Part 68 rules and requirements
adopted by the ACTA. A compliant telephone cord and
modular plug is provided with this product. It is
designed to be connected to a compatible modular jack
that is also compliant. See installation instructions for
details.
4. The REN is used to determine the quantity of devices
which may be connected to the telephone line.
Excessive RENs on the telephone line may result in the
®
8 - English
devices not ringing in response to an incoming call. In
most, but not all areas, the sum of the RENs should not
exceed five (5.0). To be certain of the number of
devices that may be connected to the line, as
determined by the total RENs, contact the local
telephone company. For products approved after July
23, 2001, the REN for this product is part of the product
identifier that has the format US:AAAEQ##TXXXX. The
digits represented by ## are the REN without a decimal
point (e.g., 03 is a REN of 0.3). For earlier products, the
REN is separately shown on the label.
5. If the equipment, MPS5500mb/MPS5500mbf, causes
harm to the telephone network, the telephone company
will notify you in advance that temporary
discontinuance of service may be required. But if
advance notice isn't practical, the telephone company
will notify the customer as soon as possible. Also, you
will be advised of your right to file a complaint with the
FCC if you believe it is necessary.
6. The telephone company may make changes in its
facilities, equipment, operations, or procedures that
could affect the operation of the equipment. If this
happens, the telephone company will provide advance
notice in order for you to make the necessary
modifications to maintain uninterrupted service.
7. If trouble is experienced with this equipment
(MPS5500mb/MPS5500mbf), please contact the
following for repair and/or warranty information:
Oki Data Americas, Inc.
2000 Bishops Gate Blvd.
Mount Laurel, N.J. 08054-4620
Telephone:(856) 235-2600 or
(800)-OKIDATA (800-654-3282)
If the equipment is causing harm to the telephone
network, the telephone company may request that you
disconnect the equipment until the problem is resolved.
8. This equipment contains no user serviceable parts.
Please contact Oki Data for service.
9. This equipment cannot be used on public coin service
provided by the telephone company. Connection to
Party Line Service is subject to state tariffs. Contact
your state Public Utility Commission, Public Service
Commission, or Corporate Commission for information.
10.If your home has specially wired alarm equipment
connected to the telephone line, ensure the installation
of this MPS5500mb/MPS5500mbf does not disable your
alarm equipment. If you have questions about what will
disable alarm equipment, consult your telephone
company or a qualified installer.
FCC Telephone Consumer Protection Act
The Telephone Consumer Protection Act of 1991 makes it
unlawful for any person to use a computer or other
electronic device, including FAX machines, to send any
message unless such message clearly contains in a margin
at the top or bottom of each transmitted page or on the
first page of the transmission, the date and time it is sent
and an identification of the business or other entity, or
other individual sending the message, and the telephone
number of the sending machine or such business, other
entity, or individual. (The telehone number provided may
not be a 900 number or any other number for which
charges exceed local or long-distance transmission
charges.)
To comply with this law, you must enter the following
information in your fax unit:
• Date and time: see "Changing the Date and Time"
under Setting Your Terminal in the User's Guide for
instructions on doing this.