1. Manuals
  2. Brands
  3. Chamberlain Manuals
  4. Intercom System
  5. LiftMaster ELITE EL2000
  6. Installation manual

Chamberlain Elite EL2000 Installation Manual

El25 - installation manual
Hide thumbs Also See for Elite EL2000:
Table of Contents

Advertisement

Quick Links

See also: Programming Manual
®
®
™
™
Installation Manual for
Installation Manual for
EL MODELS
EL MODELS
Telephone entry/access control system
© 2008 The Chamberlain Group, Inc.
All Rights Reserved

Advertisement

Table of Contents
loading

Related Manuals for Chamberlain Elite EL2000

Summary of Contents for Chamberlain Elite EL2000

  • Page 1 ® ® ™ ™ Installation Manual for Installation Manual for EL MODELS EL MODELS Telephone entry/access control system © 2008 The Chamberlain Group, Inc. All Rights Reserved...

  • Page 3: Table Of Contents

    Table of Contents Mounting the Unit Page Dimensions EL25 Installation Rotating the Keypad for Vertical Mounting Unlocking/Locking EL2000 EL2000 Installation Wire Type Wire Connections to Unit (Factory Settings for Relays) Wire Specs and Run Distances Power Wire Specs and Run Distances...

  • Page 4: Dimensions

    6 in. 3-15/16 in. 3/4 in. Conduit Hole Mounting Holes (4) for 5/16 in. Caution! A Static Discharge can Damage Circuit Boards EL2000 Units Knockouts for 3/8 in. Knockouts for 5/16 in. 9 in. AUG 10, 2005 WELCOME 7 in.

  • Page 5: El25 Installation

    EL25 Installation Caution! A Static Discharge can Damage Circuit Boards NOTE: This unit is for surface mount applications only. Unplug the 2 Main Harnesses Unlock Unit Carefully Lift Cover Up then Slide Out on Hinges Remove Back Mounting Plate from Cover Line up Notch with Screw and Push Hinge Out...
  • Page 6 Unlocking EL2000 1. Apply pressure to the right-side of the unit. 2. While maintaining pressure, turn key clockwise 3. Open cover Locking EL2000 1. Turn key counter clockwise to lock position 2. Close cover 3. Apply pressure to left-side until you hear a “click”...

  • Page 7: El2000 Installation

    EL2000 Installation NOTE: This unit is for surface and recessed mount ONLY. Unlock Unit Open Cover Slide Front Cover Out of Unplug the 2 Main Harnesses (Optional) Hinges (Optional) Knock-out Desired Mounting Plugs Using Punch Mount Back Housing to Wall or Pedestal...
  • Page 8 Wire Connections to the Unit EXIT REQ 4 LED 4 DOOR RELAY 4 STAT 4 EXIT REQ 3 POSTAL LED 3 DOOR STAT 3 RELAY 3 EXIT REQ 2 AUTO TELCO DOOR STAT 4 EXIT LED 2 POWER REQ 1 12VAC/DC RELAY 2 IO Input Board...

  • Page 9: Wire Specs And Run Distances

    Wire Specs and Run Distances Use this chart to pull wires in preparation of your installation: Description of Wire Run Maximum Distance Page Wire Specification Grounding the Chassis 12 AWG Copper 12 feet 2 Twisted Pairs 9-14 Residence and Telco Phone Lines 5000 feet* 18-24 AWG Shielded 2-Conductor...

  • Page 10: Grounding The Unit

    Grounding the Units Ensure that the system is grounded properly. The units contain a number of static sensitive components that can be damaged by static discharge. IMPORTANT: An Earth Ground Rod is Strongly Recommended and should be no further than 12 feet from the unit and use a minimum of 12 gauge wire in most cases.

  • Page 11: Wiring 1 Unit To Telco Line

    Wiring 1 Unit to Telco Line The bypass board allows the unit to be disconnected without interrupting normal telephone operation. NOTE: Installation where fiber optic phone lines are present may require additional modifications from your telephone provider. Contact your provider for more information. •...

  • Page 12: Wiring Multiple Units To Telco Line

    Wiring Multiple Units to Telco Line Up to 7 units can share the same phone line. The bypass boards allow the units to be disconnected without interrupting normal telephone operation. NOTE: Installation where fiber optic phone lines are present may require additional modifications from your telephone provider.

  • Page 13: Wiring With No Telco Line

    Wiring with No Telco Line The unit can be a stand alone system that allows communication between the unit and a resident’s phones. Single Unit NOTE: Ringer Equivalence Number (REN) of “5” maximum. Output Board (See page 6) Use 18-24 AWG 2 twisted pair Ring TELCO...

  • Page 14: Wiring To Dedicated Telco Line

    Wiring to Dedicated Telco Line NOTE: Installation where fiber optic phone lines are present may require additional modifications from your telephone provider. Contact your provider for more information. Single Unit Telco Entrance Box Demarcation Point LED 4 Use 18-24 AWG RELAY 4 Ring 2 twisted pair...

  • Page 15: Wiring To An Internal Phone System

    Wiring to an Internal Phone System The units can be wired to any Analog Trunk in an internal home phone system. NOTE: Installation where fiber optic phone lines are present may require additional modifications from your telephone provider. Contact your provider for more information. Single Unit Analog Trunk...

  • Page 16: Connection To An Npbi System

    Connection To An NPBI System Single Unit Sentex Ovation Unit LED 4 Use 18-24 AWG RELAY 4 2 twisted pair LED 3 RELAY 3 Ring TELCO LED 2 RELAY 2 Never run Telco wires and High Voltage wires in the same conduit.

  • Page 17: Wiring A Door Strike Lock

    Wiring a Door Strike Lock Output Board (See page 6) DO NOT overload the removable terminal block connectors. One LED 4 wire per hole. RELAY 4 LED 3 RELAY 3 Normally Open TELCO For AC Power: Install a Siemens S10K30 MOV LED 2 For DC Power: Install a (Metal Oxide Varistor) or...

  • Page 18: Wiring A Gate Operator

    Wiring a Gate Operator Output Board (See page 6) LED 4 RELAY 4 DO NOT overload the removable terminal block connectors. One wire per hole. LED 3 RELAY 3 TELCO LED 2 Normally Open RELAY 2 Common Use 18-24 AWG LED 1 RELAY 1 NOTE: The gate operator can be...

  • Page 19: Wiring A Door Sensing Device

    Wiring a Door Sensing Device The units can monitor the position of up to four doors/gates and may react to a change in their status with one of the relays (not set as a control relay). For example, if a door is pried open or is held open after its relay deactivates, the unit will record the breach in its transactions and can perform the following actions: •...

  • Page 20: Wiring A Radio Frequency Module

    Wiring a Radio Frequency Module An optional radio frequency module and a remote antenna can be installed if the residents will access a controlled area with a transmitter. Refer to instructions supplied with the optional RF Module for more information. NOTE: The remote can control 1-4 doors.

  • Page 21: Wiring A Postal Lock Switch

    One wire per hole. (See page 6) NOTE: In the EL2000 models, the postal lock switch is pre-wired. Wiring an Internal Camera [CCTV] An Optional CCTV (Close Circuit Television) camera can be installed inside the unit. Refer to instructions supplied with the camera kit for more information.

  • Page 22: Wiring Power To The Unit

    Wiring Power to the Unit The 110 VAC outlet must be dedicated to the unit ONLY. This outlet should be wired back to its own 10 Amp minimum circuit breaker. This will prevent two problems: • Other equipment cannot introduce spikes, noise, surges or dips into the power circuit. •...

  • Page 23: Powering Up And Checking The Leds

    LCD Display. Connector J406 EL25=LED BOTTOM For the EL25 provides power to bottom lighted LEDs for the main keypad. KEYPAD On the EL2000 this is the top lighted LEDs for main keypad. EL2000=LED keypad Connector J201 Microphone connector Connector...

  • Page 24: Troubleshooting

    Troubleshooting Wiring • Check for correct length and AWG of wires. See page 7. • Check that wires are correctly inserted into the terminal blocks (not loose, no two sharing the same position). • Check board markings for correct terminal block placements. •...
  • Page 25 Repair Parts Installation and Service Information is Available EL25 Parts Call our Toll Free Number 1-800-528-2806 www.chamberlain.com When ordering repair parts, please supply the following information: Description and Model Number Part Description Model Number Part Description Model Number Silver Cover 93D341 Assembly, LED, Focus 2B721...

  • Page 26: Repair Parts

    Description and Model Number Part Description Model Number Part Description Model Number Assembly Display and Display Board 41B989 Interconnect Board 41B997 Assembly, Lock and Key EL2000 41B999 Display Cables Kit 41B990 Assembly, PCB Output Board 2B737 Replacement Key 41B12 Assembly, PCB Input Board...
  • Page 27 Your System Diagram Page 25...
  • Page 28 Your Wiring Configuration External Access Control Device(s) connected to optional board(s) (Default Internal Keypad) Device 0 ________________________________________________________________________________ J400 Position on Main Board RF Module Wiegand Device 1 ________________________________________________________________________________ Wiegand Device 2 ________________________________________________________________________________ J407 Position on Main Board RF Module Wiegand Device 3 ________________________________________________________________________________ Wiegand Device 4 ________________________________________________________________________________...
  • Page 29 EL25BWCAMKT (Black & White Camera) Directory Insert EL25DVRCAMKT (Low Lux DVR Color Camera) ELDI EL25CAMKT (Color Camera) Wiegand Module Kit WOMODKT EL2000 Camera Kits EL2000BWCAMKT (Black & White Camera) EL2000DVRCAMKT (Low Lux DVR Color Camera) EL2000CAMKT (Color Camera) Heater Kit RF Module Kit ELHTRKT...
  • Page 30 FCC and DOC Requirements FCC Requirements The units comply with Part 68 of the FCC Rules. The label affixed to this equipment contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone company.
  • Page 32 ® ™ 845 Larch Avenue Elmhurst, Illinois 60125-1196 © 200 8 The Chamberlain Group, Inc. All Rights Reserved 114A2980 F...

This manual is also suitable for:

Elite el25

Table of Contents