Setting Up The System - Denon 1083 Operating Instructions Manual

7 SETTING UP THE SYSTEM

• Once all connections with other AV components have been completed as described in "CONNECTIONS" (see pages 6 to 13), make the various
settings described below on the monitor screen using the AVR-3803/1083's on-screen display function.
These settings are required to set up the listening room's AV system centered around the AVR-3803/1083.
• Use the following buttons to set up the system:
• Check that the remote control unit is set to AMP mode.
• System setup items and default values (set upon shipment from the factory)
Input the combination of speakers in your system and their
Speaker corresponding sizes (SMALL for regular speakers, LARGE for full-
Configuration size, full-range) to automatically set the composition of the signals
output from the speakers and the frequency response.
Use this function when using multiple surround speaker
combinations for more ideal surround sound. Once the
Surround
combinations of surround speakers to be used for the
Speaker
q
different surround modes are preset, the surround
Setting
speakers are selected automatically according to the
surround mode.
Crossover Set the frequency (Hz) below which the bass sound of the various
Frequency speakers is to be output from the subwoofer.
Subwoofer mode This selects the subwoofer speaker for playing deep bass signals.
This parameter is for optimizing the timing with which the audio
w
Delay Time signals are produced from the speakers and subwoofer according to
the listening position.
This adjusts the volume of the signals output from the speakers and
Channel
e
subwoofer for the different channels in order to obtain optimum
Level
effects.
Digital In This assigns the digital input jacks for the different input
r
Assignment sources.
Component
In Assign
t
Video Setup
Video Input
Mode
Dolby Digital Turn the audio compression on or off when down-mixing Dolby
y
Setup Digital signals.
Power AMP
Assignment
Zone 2
u
Control
Zone2
vol. Level
Set the audio delay to delay time the sound and synchronize it with
i
Audio Delay
the picture.
Ext. In
o
Subwoofer Set the Ext. In Subwoofer terminal playback level.
Level
Auto Surround
!0
Set the Auto surround mode function.
Mode
This sets whether or not to display the on-screen display that
On Screen appears on the monitor screen when the controls on the remote
!1
Display control unit or main unit are operated.
A setting to prevent flickering.
16
System setup
This assigns the color difference (component) video
input jacks for the different input sources.
Set the input signal to be output from the monitor
output terminal.
Set this to switch the surround back channel's
power amplifier for use for zone 2.
This sets the output level for the zone 2 output
jacks.
SYSTEM SETUP button
Press this to display the system setup menu.
CURSOR buttons
F and G: Use these to move the cursors (F and G) to the
left and right
D and H: Use these to move the cursors (D and H) to the
up and down on the screen.
ENTER button
Press this to switch the display.
Also use this button to complete the setting.
Front Sp. Center Sp.
Large Small
DOLBY/
Surround
DTS WDE SCREEN
mode
SURROUND
Surround
A A
speaker
Front L & R Center
12 ft (3.6 m) 12 ft (3.6 m)
Front L Front R Center
0 dB 0 dB 0 dB
Input
CD DVD VDP
source
Digital
COAX1 COAX2 OPT1
Inputs
DVD VDP TV
VIDEO1 NONE NONE
on the screen.
Default settings
Surround Sp.
Sub Woofer
A / B
Yes Small
5CH/7CH DSP
STEREO SIMULATION
A A
80 Hz
LFE
Sub Woofer Surround L & R
12 ft (3.6 m) 10 ft (3.0 m)
Surround Surround Surround
L R Back L
0 dB 0 dB 0 dB
TV DBS V. AUX VCR-1
OPT2 OPT3 OFF OPT4
DBS VCR-1 VCR-2 V. AUX
VIDEO2 NONE NONE NONE
AUTO
OFF
Surround Back
Variable
0 ms
Subwoofer = +15 dB
Auto Surround Mode = ON
On Screen Display = ON / Mode 1
Surround Back Sp.
Small / 2spkrs
EXT. IN
A
SBL & SBR
10 ft (3.0 m)
Surround
Subwoofer
Back R
0 dB 0 dB
VCR-2 CDR/TAPE
OFF OPT5
— —
— —