Advertisement
BFH261/265IUK07EM1.qxd
6/8/07
9:28 AM
Page 5
BFH261/265
Fig.1
A
F
G (BFH265)
Fig.2
B
D
E
C
PRESS
TEMPERATURE
1
II
HIGH (2 kW)
2
I
LOW (1 kW)
HIGH (2 kW)
3 - 7
II
16°C, 18°C, 20°C,
22°C, 24°C
LOW (1 kW)
8 - 12
I
16°C, 18°C, 20°C,
22°C, 24°C
13
O/Off
O/Off
ADDITIONAL FEATURES:
1. Press & hold
at any time to turn the heater off. Heater will save the
last setting in memory.
2. Press
to turn heater on and heater will recall the last setting in memory.
3. Select the desired thermostat setting. The heater will cycle ON and OFF
as it maintains the preset temperature.
NOTE: 1Touch
TM
has memory. The 1Touch
U.K. and IRELAND
thermostat will remember the previous
temperature setting after the unit has been
turned off by holding the MODE/OFF button for
GENERAL DESCRIPTION (FIG. 1-2)
3 seconds. However, if the unit is unplugged,
A. Power Light
the 1Touch
TM
thermostat will be reset and will no
longer remember the previous temperature setting.
B. Pre-Set Temperature Lights
C. Low Power
Oscillation Instructions (BFH265 only)
D. High Power
Press
button (G) to start and
E. Mode/Off Control
(G) again to stop oscillation.
F. Base
AUTO SAFETY SHUT-OFF
G. Oscillation Button ( For BFH265 only )
This heater is equipped with a technologically
advanced, safety system that requires the user
OPERATING INSTRUCTIONS
to reset the heater if there is a potential
Your heater is equipped with a technologically
overheat situation. When a potential overheat
advanced 1Touch
TM
electronic thermostat. You
temperature is reached, the system will
can set the heater to run continuously in manual
automatically shut the heater off. It can only
mode or set the 1Touch
TM
Thermostat to your
resume operation when the user resets the unit.
TM
desired temperature setting. The 1Touch
thermostat will automatically turn the heater ON
To reset the heater
or OFF to maintain the preset comfort level. The
1. Press the MODE/OFF button for two
comfort level ranges between 16ºC and 24ºC.
seconds or keep pressing the button until all
the temperature indicator lights are OFF.
Manual Mode Instructions
2. Unplug the heater and wait for 30 minutes for
1. Plug the heater into the wall socket.
the unit to cool down.
2. To start the heater, push the MODE/OFF (E)
3. After the 30 minutes, plug the unit in again
button once for the HIGH manual setting.
and operate normally.
3. Press the button again for the LOW manual
setting.
Safety Back-Up Fuse
In the unlikely case the heater does not respond to
4. To stop the unit, press and hold the
an overheat situation, the safety back-up fuse will
MODE/OFF button for three seconds or keep
engage. In this case, the heater will not reset.
pressing the button until all the temperature
Please contact your local service number on the
indicator lights are OFF.
back of the manual for advice.
NOTE: The Power Light (A) will remain lit
during operation. In Manual Mode, only the
PLEASE READ AND SAVE THESE
LOW (C) or HIGH (D) indicator lights will be
IMPORTANT INSTRUCTIONS
lit.
When using electrical appliances, basic safety
1TOUCH
TM
Thermostat Instructions
precautions should always be taken including
To take advantage of the 1Touch
TM
Thermostat
the following:
continue to press the MODE/OFF button until
1. Before connecting the heater, check that the
the desired temperature is set in either the
voltage indicated on the rating plate corresponds
HIGH or LOW setting. When ambient
to the main voltage in your home/office.
temperature rises above the set temperature,
2. WARNING: In order to avoid overheating, do
the heater will stop. When the ambient
not cover the heater
.
temperature drops below the set temperature,
3. DO NOT position the heater directly under a
the heater will turn on automatically.
power socket.
NOTE: When the 1Touch
TM
thermostat is set,
4. Do not use this heater in the immediate
either the HIGH (D) or LOW (C) indicator lights,
surroundings of a bath, a shower or a
and the Set Temperature Light (B) will remain lit
swimming pool.
during operation.
NOTE: It is normal for the heater to cycle ON
and OFF as it maintains the preset temperature.
To prevent the unit from cycling, you need to
raise the thermostat setting.
TM
5. If the supply cord or plug is damaged, it must
For U.K. and Ireland only:
be replaced by the manufacturer or its
If the plug is not suitable for the socket outlets in
service agent or similarly qualified person in
your home, it can be removed and replaced by
order to avoid hazard. The heater contains
a plug of the correct type. Please refer to
no user serviceable parts. Should the product
"Installation of a plug" below.
suffer damage or breakdown, it must be returned
to the manufacturer or their service agent.
INSTALLATION OF A PLUG
6. Under the environment with electrical fast
Applicable to U.K. and Ireland
transient, the product may malfunction and
button
The wires in the mains lead are coloured as
require user to reset the product.
such:
7. Do not use this heater with a programmer,
BROWN
timer or any other device that switches the
BLUE
heater on automatically, since a fire risk
Please note that the colour of these mains wires
exists if the heater is covered or positioned
incorrectly.
may not correspond with the colour markings
that identify the terminals in your plug. Please
8. Only touch the heater with dry hands.
proceed as follows:
9. DO NOT position where it can be touched by
The BROWN coloured wire must be connected
children, especially the very young.
to the terminal, which is marked with the letter
10.DO NOT use this heater outdoors.
"L" or is coloured RED.
11. Allow a safe area around the heater away
The BLUE coloured wire must be connected to
from furniture or other objects; at least 50 cm
the terminal, which is marked with the letter "N"
from the top and sides and 200 cm at the
or is coloured BLACK.
front.
DO NOT CONNECT either of these wires to the
12.Do not use this heater when it is lying on its
earth terminal in the plug. The earth terminal
side.
plug is marked with the letter "E", or with the
13.DO NOT use the heater in rooms with
earth symbol
explosive gas (e.g. petrol) or while using
YELLOW.
inflammable glue or solvent (e.g. when gluing
or varnishing parquet floors, PVC etc.).
14.DO NOT insert any objects into the heater.
15.Keep the mains cord at a safe distance from
the main body of the heater.
16.If overheating should occur, the built-in
overheating safety device will switch off the
heater.
17.Do not place the cord under a rug.
18.The heater is to be installed so that switches
and other controls cannot be touched by a
person in the bath.
NOTE: If the terminals in the plug are not
19.Avoid the use of an extension cord because
marked or if you are unsure or in doubt about
it may cause the heater to overheat.
the installation of the plug please contact a
20.CAUTION: In order to avoid a hazard due
qualified electrician. If a 13A 3-pin plug is fitted,
to inadvertent resetting of the thermal cutout,
it must be an ASTA approved plug, conforming
this appliance must not be supplied through
to BS1363 standard. Replacement 13A fuses
an external switching device, such as a timer,
must be BSI or ASTA BS1362 approved.
or connected to a circuit that is regularly
switched on and off by the utility.
-
LIVE
-
NEUTRAL
or coloured GREEN and
13 amp
Advertisement
