1. Manuals
  2. Brands
  3. HP Manuals
  4. Laptop
  5. OmniBook 2100
  6. Reference manual

HP OmniBook 2100 Reference Manual

Hp omnibook 2100: reference guide
Hide thumbs Also See for OmniBook 2100:
Table of Contents

Advertisement

Quick Links

See also: Service Manual , User Manual
HP OmniBook 2100/3100
Reference Guide

Advertisement

Table of Contents

Troubleshooting

loading

Related Manuals for HP OmniBook 2100

Summary of Contents for HP OmniBook 2100

  • Page 1 HP OmniBook 2100/3100 Reference Guide...
  • Page 2 Notice This manual and any examples contained herein are provided “as is” and are subject to change without notice. Hewlett-Packard Company makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
  • Page 3 If your computer was shipped with a product recovery CD-ROM: (i) The product recovery CD-ROM and/or support utility software may only be used for restoring the hard disk of the HP computer with which the product recovery CD-ROM was originally provided. (ii) The use of any operating system...
  • Page 4 software by Microsoft contained in any such product recovery CD-ROM shall be governed by the Microsoft End User License Agreement (EULA). Customer may transfer rights in the software to a third party only as part of the transfer of all rights and only if Customer obtains the prior agreement of the third party to be bound by the terms of this License Agreement.

  • Page 5: Table Of Contents

    Contents 1. Introducing the OmniBook ....... Taking Inventory ........Included in the OmniBook 2100/3100 box ....To buy OmniBook accessories ......OmniBook features ........Setting Up Windows ........To set up the OmniBook for the first time ....Configuring the OmniBook with the BIOS Setup utility .....
  • Page 6 To install McAfee VirusScan ......2-18 To attach a security cable....... 2-19 To set PC identification ........ 2-20 To enable hard disk drive lock ......2-20 3. Managing Battery Power......... Monitoring Battery Power......... To check the battery status ......To respond to a low-battery warning ....... To recharge a battery........
  • Page 7 5. Expanding the OmniBook ........ Installing a Hard Disk Drive ....... To replace the hard disk drive......To replace the hard disk drive holder ...... To create a Hibernate partition ......Installing a RAM Expansion Module ......To install a RAM expansion module ....... To remove a RAM expansion module ......
  • Page 8 Performance Problems ........ 7-12 Power and Battery Problems......7-13 Printing Problems ........7-15 Serial, Parallel, and USB Problems......7-16 Startup Problems........7-17 Testing the Operation ........7-18 To create a diagnostic floppy disk ......7-18 To run the diagnostic test ....... 7-19 8.

  • Page 9: Introducing The Omnibook

    Introducing the OmniBook...
  • Page 10 Corporate Evaluator’s Guide The provides information about installing alternate operating systems, as well as how to configure the OmniBook in a corporate, networked environment. Located at the HP external website. HP Support Assist CD-ROM See the Support and Service booklet for telephone numbers.

  • Page 11: Taking Inventory

    Introducing the OmniBook Taking Inventory The HP OmniBook 2100/3100 represents a new category of HP notebook computers featuring the latest mobile technologies available. It uses high-speed Intel Pentium and Pentium II processors with MMX technology, large TFT and DSTN displays, and high-capacity hard drives.

  • Page 12: To Buy Omnibook Accessories

    Buy OmniBook accessories online! For the latest accessories and options, visit us at . As new accessories become available, you’ll find them listed here. At the time of this printing, HP offers a variety of docking solutions and the following accessories and plug-in modules: Docking system and monitor stand (HP F1477A).

  • Page 13: Omnibook Features

    Introducing the OmniBook OmniBook features OmniBook—Front View 1. Power status light. 2. Built-in microphone. 3. Status panel. 4. Built-in speakers. 5. Touch pad (pointing device). 6. Click buttons. 7. Latch to open and close the OmniBook. 8. Main battery module. 9.
  • Page 14 Introducing the OmniBook OmniBook—Side View 11. PC Card slots (upper and lower). Accepts two Type II cards or one Type III card. 12. PC Card eject buttons (upper and lower PC Card slots). 13. Audio jacks (left to right): audio line-in, external microphone, audio line-out. 14.
  • Page 15 Introducing the OmniBook OmniBook—Rear View 17. Infrared port. Use this port for wireless data transmission between the OmniBook and another computer or a printer with an infrared port. You must install infrared drivers. Windows NT 4.0 does not support infrared communciation. 18.

  • Page 16: Setting Up Windows

    Introducing the OmniBook Setting Up Windows The OmniBook has either Windows 95 or Windows NT 4.0 factory-installed on the hard disk drive. When your OmniBook starts up the first time, it takes you through a series of setup screens, including installation of the operating system. This section describes how to set up the OmniBook with the factory-installed Windows operating system.

  • Page 17: To Set Up The Omnibook For The First Time

    Introducing the OmniBook To set up the OmniBook for the first time 1. Connect the power cord to the ac adapter, then plug the cord into an ac outlet. The indicator light on the ac adapter shines when powered. 2. Connect the ac adapter to the OmniBook’s left side, as shown. 3.

  • Page 18: Configuring The Omnibook With The Bios Setup Utility

    2. From the Start menu, click Shut Down, Restart the Computer. 3. When you see the HP logo, press F2 to enter the BIOS Setup utility. 4. Pointing devices are not active in the BIOS Setup utility. Press the RIGHT and LEFT arrow keys to move among menus.
  • Page 19 Introducing the OmniBook Main Menu Default Language Sets the language for this utility and for BIOS Same as messages. operating system. BIOS Revision Shows the current BIOS version. Detected automatically. System Time Sets the time using 24-hour format. Values set take effect immediately.
  • Page 20 Introducing the OmniBook System Devices Menu Default External Fn Key Sets whether left-CTRL + left-ALT on an Enabled external keyboard is interpreted as the Fn key. IDE Controller Enables the primary (hard drive) and Both secondary (optional CD-ROM drive) controllers. FDD Controller Enables the floppy disk drive.

  • Page 21: Security Menu

    Introducing the OmniBook WSS I/O address Sets the Windows Sound System I/O 530h address. AdLib I/O address Sets the AdLib synthesizer I/O address. 388h Interrupt Sets the interrupt. IRQ5 1st DMA channel Sets the DMA channel for playback. DMA1 2nd DMA channel Sets the DMA channel for recording.

  • Page 22: Power Menu

    Introducing the OmniBook Power Menu Default Power Management Mode Disables time-outs, selects a combination of Max Power time-outs, or allows customized time-outs. Savings Smart CPU Mode Enables automatic CPU power savings. Absence of keyboard, mouse, and hard disk activity could cause slower CPU response. Standby Time-out Sets the period of inactivity after which the 2 minutes...

  • Page 23: Exit Menu

    Introducing the OmniBook Boot Menu Default Diskette Drive Shows the order of boot devices. Move the 1. Diskette drive Hard Drive entries to change the order. 2. Hard drive CD-ROM Drive 3. CD-ROM drive Exit Menu Save Changes and Exit Saves Setup changes, exits, and reboots.

  • Page 24: Configuring The Omnibook With Toptools

    TopTools may be run locally on a PC or remotely by a network administrator. To run TopTools locally, click Start, Programs, HP DMI, HP TopTools. To get more information about TopTools For information on manageable HP PCs, HP TopTools, DMI, and how they lower PC operating costs, see the HP website at 1-16...

  • Page 25: Operating The Omnibook

    Operating the OmniBook...
  • Page 26 Operating the OmniBook This chapter introduces the OmniBook and helps you get familiar with basic operation including Starting and stopping the OmniBook. Using the OmniBook touch pad. Using the OmniBook display. Adjusting the audio system. Using the OmniBook keyboard. Checking the status of the OmniBook. Protecting the OmniBook.

  • Page 27: Starting And Stopping The Omnibook

    Operating the OmniBook Starting and Stopping the OmniBook You can easily start and stop your OmniBook using the blue power button. However, at certain times, you may want to use other methods for starting and stopping your OmniBook—depending on power considerations, types of active connections, and start-up time.

  • Page 28: To Reset The Omnibook

    Operating the OmniBook To reset the OmniBook If Windows or the OmniBook stops responding, you can reset the OmniBook. If possible, from the Start menu, shut down the OmniBook. Insert a pen or straightened paper clip into the recess on the rear of the OmniBook, as shown.

  • Page 29: Using The Omnibook Touch Pad

    Operating the OmniBook Using the OmniBook Touch Pad The touch pad, a touch-sensitive pointing device which controls the motion and speed of the pointer on the screen, is built into your OmniBook. This section describes how to Use the touch pad. Configure the touch pad.

  • Page 30: To Configure The Touch Pad

    Operating the OmniBook To configure the touch pad To customize the operation of the touch pad (and an external PS/2 or serial mouse, if installed), use the Windows Control Panel Mouse icon to access Mouse Properties. Select the tab corresponding to the item you wish to configure. Among the items that can be configured are Button configuration for right or left handed operation.

  • Page 31: Using The Omnibook Display

    Operating the OmniBook Using the OmniBook Display This section describes how to Adjust the display brightness and contrast. Extend the life of the display. To adjust the display brightness and contrast Brightness affects battery time To maximize your battery operating time, set the brightness to the lowest comfortable setting.

  • Page 32: Adjusting The Audio System

    Operating the OmniBook Adjusting the Audio System The OmniBook supports Sound Blaster Pro-compatible sound and the Microsoft Windows Sound System. This section describes how to Adjust the volume manually. Adjust the volume in Windows. To adjust the volume manually To increase the volume, press Fn+UP-ARROW. To decrease the volume, press Fn+DOWN-ARROW.

  • Page 33: Using The Omnibook Keyboard

    Operating the OmniBook Using the OmniBook Keyboard This section describes the OmniBook’s keyboard features including how to Use the Fn hot keys. Use the Windows keys. Use the embedded keypad. Use the ALT GR key on a non-US keyboard.

  • Page 34: To Use The Fn Hot Keys

    Operating the OmniBook To use the Fn hot keys The combination of the Fn key plus another key creates a hot key—a shortcut key sequence—for various system controls. The OmniBook keyboard shows the Fn hot keys labeled in gray. Fn + F1 Decreases the display’s brightness.

  • Page 35: To Use The Windows Keys

    Operating the OmniBook To use the Windows keys Windows keys are located on the keyboard to the left and right of the spacebar. Brings up the Windows Start menu. There are two of these, one to each side of the spacebar. Brings up the shortcut menu for the current application.

  • Page 36: To Use The Alt Gr Key

    Operating the OmniBook To use the ALT GR key Non-U.S. keyboards have an ALT GR key to the right of the spacebar. This is a shift key providing access to certain keyboard characters. For a character in the lower-right corner of a key, press and hold ALT GR to type the character.

  • Page 37: Checking The Status Of The Omnibook

    Operating the OmniBook Checking the Status of the OmniBook This section describes how to Interpret the status lights. Interpret the status panel indicators. To interpret the status lights The OmniBook has a power status light on the hinge, which is visible even when the OmniBook is closed.

  • Page 38: To Interpret The Status Panel Indicators

    Operating the OmniBook To interpret the status panel indicators The OmniBook status panel, located above the keyboard, contains indicators that show the current power status, drive status, and keyboard status. Power Status Icons AC power. The ac adapter is connected. Battery status.
  • Page 39 Operating the OmniBook Drive Status Icons. Hard disk drive or plug-in drive. The OmniBook is accessing the hard disk drive or one of the plug-in accessory drives. Floppy disk drive. The OmniBook is accessing the floppy disk drive. PC Card. There is activity between the PC Card and the computer. Keyboard Status Icons Caps Lock.

  • Page 40: Protecting The Omnibook

    Operating the OmniBook Protecting the OmniBook Your OmniBook provides several ways for you to identify and protect your computer. This section describes how to Set or change a password. Delete a password. Install McAfee VirusScan. Attach a security cable. Set a PC identification number. Enable hard disk drive lock.

  • Page 41: To Set Or Change A Password

    1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. Select the Security menu. 4. Select Set Administrator Password, then press ENTER.

  • Page 42: To Delete A Password

    1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. Select the Security menu. 4. Select Set Administrator Password, then press ENTER.

  • Page 43: To Attach A Security Cable

    Operating the OmniBook To attach a security cable Your OmniBook has a built-in connector that allows you to secure the OmniBook with a cable. The Kensington MicroSaver lock system works with this connector and is available at many computer stores. 1.

  • Page 44: To Set Pc Identification

    Hard disk drive lock helps you keep your information secure. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the Security menu, enable Password Required To Boot.

  • Page 45: Managing Battery Power

    Managing Battery Power...

  • Page 46: Managing Battery Power

    Managing Battery Power The OmniBook conserves power by using Advanced Power Management (APM), software that controls battery charging and power drain. The OmniBook provides several safeguards so you won’t be surprised by a dead-battery condition, including the following: The battery status indicator shows the remaining battery charge. Built-in warnings are displayed for low-battery conditions.

  • Page 47: Monitoring Battery Power

    Managing Battery Power Monitoring Battery Power The primary source of power for the OmniBook is its rechargeable battery pack. You can use the ac adapter to recharge the battery—or to run on ac power to preserve the battery. Running external connections is a power-intensive operation that significantly shortens the length of a battery session.

  • Page 48: To Check The Battery Status

    Managing Battery Power To check the battery status From the Status Panel The following table explains the OmniBook status panel battery icons. Shows the approximate charge level of the battery relative to a full charge. Each bar (displayed from right to left), represents a 10% Full battery charge.

  • Page 49: To Respond To A Low-Battery Warning

    Managing Battery Power To respond to a low-battery warning When battery power is critically low, you are alerted by one or more of the following: The battery indicator in the status panel appears empty. The computer emits a warning beep. This reminds you to save your work. If the OmniBook has been off, you will not be able to turn it on.
  • Page 50 Managing Battery Power Charging time Charging the battery takes about 1.5 hours. Battery life When the computer is in use, typical battery life can last up to 2 to 3 hours, depending on your level of use and your power management settings (see page 1-14).

  • Page 51: To Replace The Main Battery

    Managing Battery Power To replace the main battery . Save your work. 2. Plug in the ac adapter. From the Start menu, shut down the OmniBook. 3. Slide the safety latch for the battery compartment into its recess. 4. Slide the release latch forward, then pull out the battery, as shown. 5.

  • Page 52: To Install A Secondary Battery

    Managing Battery Power To install a secondary battery The OmniBook’s plug-in module bay accepts a secondary battery. See page 4-4 for more information about plug-in modules. When a secondary battery is installed, a lower triangle appears next to the battery icon in the status panel.

  • Page 53: Conserving Battery Power

    Managing Battery Power Conserving Battery Power The OmniBook uses Advanced Power Management (APM) to conserve battery power. You can take steps to optimize your battery operating time. This section describes how to Optimize battery life. Set time-outs. Handle and store the battery safely. Get the most from your battery.

  • Page 54: To Set Time-Outs

    1. From the Start menu, shut down then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. Active keys are described along the bottom of the screen. (The touch pad does not work in Setup.) Help information for the highlighted item appears in the right-hand...

  • Page 55: To Get The Most From Your Battery

    Managing Battery Power To get the most from your battery The following are some further suggestions for the best management of your OmniBook batteries. Do not leave batteries unused for long periods of time. If you have more than one, rotate them. If you normally use ac power, make a practice of at least once a week using the battery as your power source.

  • Page 57: Making Connections

    Making Connections...

  • Page 58: Making Connections

    Making Connections This chapter describes procedures to expand the capabilities of your OmniBook, including Using OmniBook plug-in modules. Connecting external devices. Using PC Cards. Using docking products.

  • Page 59: Using Omnibook Plug-In Modules

    Insert or eject an Zip disk. The floppy drive module can also be connected externally via the parallel port. If you want to do this, you’ll need to order the external floppy cable (HP F1380A). You can order this online at http://www.hp.com/omnibook.

  • Page 60: To Replace A Plug-In Module

    Making Connections To replace a plug-in module If you are inserting or removing a CD-ROM drive, floppy drive, or Zip drive, shut down the OmniBook. 1. From the Start menu, shut down the OmniBook. (This is not necessary if you are removing a battery from the plug-in module bay and inserting another battery.) 2.

  • Page 61: To Connect The Floppy Disk Drive Externally

    CD-ROM drive, a Zip drive, or a secondary battery. Connect the external floppy disk drive cable (optional accessory, HP F1380A) to the OmniBook parallel port. Only one floppy disk drive is supported on the OmniBook. You cannot use both an external floppy disk drive and a plug-in floppy disk drive.

  • Page 62: To Insert Or Remove A Cd

    Making Connections To insert or remove a CD 1. Press the button on the face of the CD-ROM drive. 2. If one is present, remove the cardboard shipping insert. 3. Place the CD into the drive (label facing up) and gently press down to seat the CD on the spindle.

  • Page 63: To Insert Or Eject A Zip Disk

    Making Connections To insert or eject a Zip disk Always turn on power to the OmniBook before inserting a Zip disk. To insert the Zip disk, hold the disk with its face up, then gently slide it into the Zip drive. To remove the Zip disk, press the eject button on the front of the Zip drive.

  • Page 64: Connecting External Devices

    Making Connections Connecting External Devices Your OmniBook is a powerful computer in its own right—but you can greatly expand its capabilities by connecting other devices. Before you connect any device, check the documentation that came with the equipment to see if you need to make any settings or adjustments to the equipment before using it.

  • Page 65: To Indentify The External Ports

    Making Connections To indentify the external ports The following graphic describes the available connectors for external devices. Refer to it, if necessary, when following the procedures in this section. 1. Infrared port. Use this port for wireless data transmission between the OmniBook and another computer or a printer with an infrared port.

  • Page 66: To Connect An External Display

    1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the Main menu, use the down arrow to highlight Video Display Device.

  • Page 67: To Connect A Parallel Device

    1. From the Start menu, shut down the OmniBook. 2. Plug the mouse or keyboard PS/2 cable into the PS/2 port on the OmniBook. To connect both a mouse and a keyboard, use the HP F1469A PS/2 Y adapter. To connect a device that has a PC-type jack, first connect its cable to an adapter cable with a PS/2 jack.

  • Page 68: To Connect Usb Devices

    Making Connections To connect USB devices Windows NT 4.0 does not support universal serial bus (USB) devices. Universal serial bus (USB) provides a bi-directional serial interface for adding peripheral devices such as game controllers, serial and parallel ports, and scanners on a single bus.

  • Page 69: To Connect Audio Devices

    Making Connections To connect audio devices Your OmniBook has a built-in microphone and two stereo speakers. The audio jacks allow you to plug in external audio devices. Plug a stereo input source (such as a CD player) into the input (left) jack. Plug the microphone-into the microphone (middle) jack.

  • Page 70: To Make An Infrared Connection

    Making Connections To make an infrared connection Windows NT 4.0 does not support infrared communication. By default, the infrared port is not enabled. You must enable it in the BIOS Setup utility and then install the appropriate infrared driver. For details, refer to the driver’s Readme file located in \OmniBook\drivers\Win95.

  • Page 71: Using Pc Cards

    Making Connections Using PC Cards This section describes how to Insert a PC Card. Remove a PC Card. Find a list of tested PC Cards. To insert a PC Card Windows NT 4.0 does not support zoomed video. If you are using Windows NT 4.0, make sure you’ve installed Card Executive (see page 6-21 for instructions).

  • Page 72: To Remove A Pc Card

    4. Push in the ejector button until it is flush with OmniBook case. To find tested PC Cards For the latest information about compatible cards, visit our website at http://www.hp.com/omnibook and check the Accessories section. Or contact Hewlett-Packard as described in the Support and Service booklet. 4-16...

  • Page 73: Using Docking Products

    Your dock requires a tray that accommodates your specific OmniBook model. Install this tray prior to connecting the OmniBook to the dock. 1. Select the tray labeled for the OmniBook 2100 or 3100. 2. Slide the rear of the tray into the dock as shown on the dock label.

  • Page 74: To Dock The Omnibook

    Making Connections To dock the OmniBook 1. If you’re using Windows NT, click Start, Shut Down. 2. Plug the power cord into the ac adapter, then into an ac outlet. Plug the ac adapter into the dock. 3. On the rear of the OmniBook, slide the docking door to the left. 4.

  • Page 75: To Undock The Omnibook

    Making Connections To undock the OmniBook 1. If you’re using Windows NT, click Start, Shut Down. 2. Press the undock button on the front of the dock and wait for the undock light to turn green. Then position your thumb as shown and pull the release lever forward.

  • Page 77: Expanding The Omnibook

    Expanding the OmniBook...

  • Page 78: Expanding The Omnibook

    Expanding the OmniBook This chapter describes some of the optional equipment that can be added to the OmniBook—components installed inside the computer rather than connected to the computer’s I/O ports. This chapter describes procedures to expand or update the capabilities of your OmniBook, including Installing a hard disk drive.

  • Page 79: Installing A Hard Disk Drive

    Expanding the OmniBook Installing a Hard Disk Drive This section describes how to Replace the hard disk drive. Replace the hard disk drive holder. Create a hibernate partition for a new hard disk drive. To replace the hard disk drive You’ll need a small Phillips screwdriver to remove the hard disk drive.

  • Page 80: To Replace The Hard Disk Drive Holder

    Expanding the OmniBook To replace the hard disk drive holder If you are installing a new hard drive that does not have a plastic holder, you can remove the holder from the old hard drive. You’ll need a small Phillips screwdriver for this procedure. 1.

  • Page 81: To Create A Hibernate Partition

    \Omnibook\Drivers\Hputils directory on the OmniBook Recovery CD. (Note: Use the \Omnibook\Drivers\Hputils directory, not \OmniBook \Hputils). On any computer, download the Support Utility software package from the OmniBook website (http://www.hp.com/omnibook). Follow the instructions provided. 1. Connect the ac adapter to the OmniBook.

  • Page 82: Installing A Ram Expansion Module

    SDRAM modules (F1456A, ...) or EDORAM modules (F1363A, ...) in the slots—but do not put a module larger than 32 MB in the slot nearest the corner of the computer. The easiest way to avoid RAM configuration problems is to use HP SDRAM modules exclusively. This section describes how to Install a RAM expansion module.

  • Page 83: To Install A Ram Expansion Module

    Expanding the OmniBook To install a RAM expansion module Your OmniBook’s computer chips are extremely static-sensitive. Static electricity can permanently damage computer chips. Before starting, reading the caution on page 5-6 about how to handle RAM expansion modules. You’ll need a small Phillips screwdriver to complete this procedure. 1.

  • Page 84: To Remove A Ram Expansion Module

    Expanding the OmniBook To remove a RAM expansion module Your OmniBook’s computer chips are extremely static-sensitive. Static electricity can permanently damage computer chips. Before starting, reading the caution on page-5-6 about how to handle RAM expansion modules. You’ll need a small Phillips screwdriver to complete this procedure. 1.

  • Page 85: Using The Recovery Cd

    Using the Recovery CD...
  • Page 86 Using the Recovery CD You can use the OmniBook Recovery CD to recover an original OmniBook build, or you can use it to install the HP custom software over a user-installed alternate operating system. The Recovery CD provides the OmniBook-specific drivers to configure your custom system.

  • Page 87: Recovering A Factory Software Installation

    Using the Recovery CD Recovering a Factory Software Installation If you’ve deleted or lost files on the OmniBook, causing the system to work improperly, you may need to recover the original factory build. This section describes how to Recover the OmniBook factory installation of Windows 95. Recover the OmniBook factory installation of Windows NT 4.0.

  • Page 88: To Recover The Windows 95 Factory Installation

    2. Connect the ac adapter and turn on the OmniBook. 3. When you see the HP logo, press F2 to enter the BIOS Setup utility. 4. Open the Boot menu and select CD-ROM as the first boot device. (You may want to change the boot order back to Diskette Drive after completing this procedure.)

  • Page 89: To Recover The Windows Nt Factory Installation

    2. Connect the ac adapter and turn on the OmniBook. 3. When you see the HP logo, press F2 to enter the BIOS Setup utility. 4. Open the Boot menu and select CD-ROM as the first boot device. (You may want to change the boot order back to Diskette Drive after completing this procedure.)

  • Page 90: Installing Retail Windows 95

    Using the Recovery CD Installing Retail Windows 95 If you install a retail version of Windows 95, you’ll also need to manually install video, audio, touch pad, PC Card, and infrared drivers. This section describes how to Install a retail version of Windows 95. Install video support for retail Windows 95.

  • Page 91: To Install A Retail Version Of Windows 95

    2. Connect the ac adapter and turn on the OmniBook. 3. When you see the HP logo, press F2 to enter the BIOS Setup utility. 4. Open the Boot menu and select CD-ROM as the first boot device. (You may want to change the boot order back to Diskette Drive after completing this procedure.)
  • Page 92 28. Do not detect any Network, Sound, MIDI, or Video Capture Card devices, then click Next. 29. Follow the prompts until the end of the installation, and then reboot. 30. Copy the files in D:\Omnibook from the OmniBook 2100/3100 Recovery CD to C:\Omnibook. 31. Insert the OmniBook Recovery CD.

  • Page 93: To Install Video Support For Retail Windows 95

    Using the Recovery CD 37. Remove any PCI devices (Cards or Bridges) from the Other devices category. 38. Close the System Properties window. 39. Shut down and restart Windows 95. 40. If you are prompted for a PCI Card driver, select Do Not Install A Driver, then click OK.

  • Page 94: To Install Audio Support For Retail Windows 95

    Using the Recovery CD To install audio support for retail Windows 95 If you’ve installed a retail version of Windows 95, you’ll need to install audio support. This driver is located on the OmniBook’s hard drive or on the Recovery CD in \Omnibook\Drivers\Win95\Audio.

  • Page 95: To Install Pc Card Support For Retail Windows 95

    Using the Recovery CD To install PC Card support for retail Windows 95 If you’ve installed a retail version of Windows 95, you’ll need to install PC Card support. This driver is located on the OmniBook’s hard drive or on the Recovery CD in \Omnibook\Drivers\Win95\Pccard\950aonly.

  • Page 96: To Install Infrared Support For Retail Windows 95

    2. If prompted to overwrite old files, click Yes. 3. Reboot the OmniBook. 4. When you see the HP logo, press F2 to enter the BIOS Setup utility. 5. Go to the System Devices menu. 6. Set the Infrared Port to Enabled.

  • Page 97: To Install Touch Pad Support For Retail Windows 95

    Using the Recovery CD 22. Select Show all Files and deselect Hide MS-DOS file extensions for file types that are registered, then click OK. 23. Right-click on SMCIRLAP.INF in the \Omnibook\Drivers\Win95\Fastir directory. 24. Click Install off the pop-up menu. 25. If prompted for the location of SMCIRLAP.INF enter \Omnibook\Drivers\Win95\Fastir, then click OK.

  • Page 98: To Disable Automatic Cd-Rom Detection

    Using the Recovery CD To disable automatic CD-ROM detection Windows 95 automatically detects a CD when you insert it. However, this prevents the OmniBook from automatically turning off after a period of inactivity if the CD-ROM drive is installed. You can disable this feature with the following procedure.

  • Page 99: Installing Retail Windows Nt 4.0

    Using the Recovery CD Installing Retail Windows NT 4.0 If you install a retail version of Windows NT 4.0 you’ll also need to manually install video, audio, touch pad, Advanced Power Management (APM), and Card Executive drivers. This section describes how to Install a retail version of Windows NT 4.0.

  • Page 100: To Install A Retail Version Of Windows Nt 4.0

    2. Connect the ac adapter and turn on the OmniBook. 3. When you see the HP logo, press F2 to enter the BIOS Setup utility. 4. From the Boot menu, select CD-ROM as the first boot device. (You may want to change the boot order back to Diskette Drive after completing this procedure.)

  • Page 101: To Install Service Pack 3 For Retail Windows Nt 4.0

    Using the Recovery CD When choosing a file system, refer to the Windows NT Resource Kit for a detailed discussion of FAT and NTFS file systems. 13. When prompted, choose No, Do Not Create An Emergency Repair Disk, then click Next. If is more useful to create a repair disk after installation is complete and after you have installed your drivers and other applications.

  • Page 102: To Install Video Support For Retail Windows Nt 4.0

    When you see this message, click OK. 13. Select the following resolution, click Test, click OK. 1024 x 768 for OmniBook 3100 800 x 600 for OmniBook 2100 14. If the graphic is correctly displayed, click Yes, otherwise click No and change the setting.

  • Page 103: To Install Audio Support For Retail Windows Nt 4.0

    Using the Recovery CD To install audio support for retail Windows NT 4.0 If you’ve installed a retail version of Windows NT 4.0, you’ll need to install audio support. The driver is located on the Recovery CD in \Omnibook\Drivers\Nt40\Audio. 1. Insert the Recovery CD into the CD-ROM drive. 2.

  • Page 104: To Install Apm For Windows Nt 4.0

    Using the Recovery CD To install APM for Windows NT 4.0 You need to install Advanced Power Management for Windows NT 4.0 for both the retail and factory-installation. The driver is located on the Recovery CD in \Omnibook\Drivers\Nt40\Apm. Phoenix APM 2.0 adds the following capabilities to the OmniBook: Improved battery life under Windows NT 4.0.

  • Page 105: To Install Card Executive 2.X For Retail Windows Nt 4.0

    Using the Recovery CD To install Card Executive 2.x for retail Windows NT 4.0 To take advantage of Card Executive’s plug-n-play for PCMCIA network cards, you must install Card Executive before installing Windows NT networking. The driver is located on the Recovery CD in \Omnibook\Drivers\Nt40\Pccard. Card Executive adds the following capabilities to your OmniBook: Plug and Play for PC Cards using standard Windows NT drivers.

  • Page 106: To Disable Automatic Cd-Rom Detection

    Using the Recovery CD To disable automatic CD-ROM detection Windows NT automatically detects a CD when you insert it. However, this prevents the OmniBook from automatically turning off after a period of inactivity if the CD-ROM drive is installed. You can disable this feature with the following procedure.

  • Page 107: Recovering Omnibook Files

    If you lose or damage the Recovery CD, take your OmniBook and Certificate of Authenticity to an HP Service Center to be replaced. If you mail your OmniBook for this service, you must provide a photocopy of the Certificate of Authenticity along with payment.

  • Page 108: To Update The Omnibook Bios

    To update the OmniBook BIOS Hewlett-Packard may update the BIOS to enhance the capabilities of the OmniBook. Updates will be available from HP Electronic Support Services. 1. From the Start menu, shut down the OmniBook. 2. Connect the ac adapter to the OmniBook.

  • Page 109: Troubleshooting

    Troubleshooting...

  • Page 110: Troubleshooting

    Look at the online Help for Windows and other applications. Find technical information about the OmniBook on the Internet—visit the Support website at http://www.hp.com/omnibook. See other books about Windows, MS-DOS, and other applications. Check your local library or bookstore.

  • Page 111: Solving Problems

    If you always want to boot from a CD, check the boot order in BIOS Setup. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. Open the Boot menu. The default boot order is...
  • Page 112 Check the boot order in BIOS Setup. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. Open the Boot menu. The default boot order is...

  • Page 113: Audio Problems

    Check settings in BIOS Setup. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the System Devices menu, check that Audio is enabled.

  • Page 114: Display Problems

    Troubleshooting Display Problems If the OmniBook is on, but the screen is blank Press the space bar to see if the computer is in Standby mode. Press Fn+F1 or Fn+F2 to adjust the display. Press Fn+F5 in case the internal display was disabled. (Do this three times to return to the state you started from.) If the OmniBook is cold, allow it to warm up.

  • Page 115: Hard Disk Drive Problems

    Troubleshooting Hard Disk Drive Problems If the OmniBook’s hard drive doesn’t spin Check the power source. Remove and reinsert the hard drive. See page 5-3 for instructions. If the hard disk makes buzzing or whining noise Back up the drive immediately. Check for alternate noise sources, such as the fan or a PC Card drive.

  • Page 116: Infrared Problems

    Check settings in BIOS Setup utility. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the System Devices menu, check that Infrared Port is enabled.

  • Page 117: Keyboard And Pointing Device Problems

    Troubleshooting Keyboard and Pointing Device Problems If the embedded numeric keypad doesn’t work Make sure Num Lock is on (Fn+F9). Make sure the embedded Keypad Lock (Fn+F8) is on—or that you press and hold the Fn key to temporarily access the embedded keypad. Don’t touch the pointing stick or the touch pad while booting or resuming.

  • Page 118: Memory Problems

    If you are having memory problems running MS-DOS programs, in Windows Help search for MS-DOS troubleshooter. If memory is less than expected The maximum supported amount of RAM using HP memory modules is 288 MB if your OmniBook has two expansion slots and a Pentium II processor.

  • Page 119: Pc Card (Pcmcia) Problems

    Troubleshooting PC Card (PCMCIA) Problems If the OmniBook doesn’t recognize a PC Card Make sure Card Executive is installed for Windows NT. Remove and reinsert the PC card. If the card requires an IRQ, check that there is one available , look in Device Manager, Properties, Interrupt Request (IRQ).

  • Page 120: Performance Problems

    Check the BIOS Setup settings. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the Power menu, set the Power Management Mode to Max.

  • Page 121: Power And Battery Problems

    1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the Power menu, make sure the Power Management Mode is set to Maximum Power Savings.
  • Page 122 Troubleshooting Turn off the OmniBook, then check that the battery contacts are clean and that the ac adapter cables are fully plugged in. Move the OmniBook away from any nearby heat source. Unplug the ac adapter and allow the battery to cool down. An elevated battery temperature prevents charging.

  • Page 123: Printing Problems

    If the printer you are using is a 600-dpi (dots per inch) printer, try selecting a compatible printer driver for a 300-dpi printer. For example, for a 600-dpi HP LaserJet printer, try using the HP LaserJet IIIsi driver (300-dpi). Certain applications may not work properly with 600-dpi printers.

  • Page 124: Serial, Parallel, And Usb Problems

    Check settings in BIOS Setup. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the System Devices menu, check that Parallel and Serial are enabled.

  • Page 125: Startup Problems

    Check settings in BIOS Setup utility. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. Open the Boot menu. The default boot order is...

  • Page 126: Testing The Operation

    On an OmniBook with a factory software installation, run from the \Dmi\Hpdiags directory on the hard disk. –or– If HP TopTools is installed, use the DiagTools page to create the disk. On any computer with a CD-ROM drive, run from the \Omnibook\Drivers\Hputils directory on the OmniBook Recovery CD.

  • Page 127: To Run The Diagnostic Test

    Troubleshooting To run the diagnostic test 1. Insert the diagnostic disk in the floppy drive. 2. Reboot the OmniBook. 3. Go through the first several screens. 4. When the hardware detection finishes, check the list of detected hardware. If a device is not detected or fails its test below, it may be configured incorrectly in the BIOS Setup utility.

  • Page 129: Specifications And Regulatory Information

    Specifications and Regulatory Information...
  • Page 130 Specifications and Regulatory Information Your OmniBook is designed to provide trouble-free operation. The following suggestions can help you maintain its dependability: Observe the temperature limits and other specifications listed in the next section. If you have problems, see the problem-solving suggestions in chapter 7 of this manual.

  • Page 131: Hardware Specifications

    Optional removable DVD drive. 32-MB RAM on board. The maximum supported amount of RAM using HP memory modules is 288 MB if your OmniBook has two expansion slots and a Pentium II processor, 192 MB is it has two expansion slots and a Pentium processor, or 160 MB if it has one expansion slot and a Pentium processor.
  • Page 132 Full line of optional docking products: port replicator, mini dock, and docking system. Microsoft Windows 95 or Windows NT 4.0. Advanced Power Management (APM 1.2). DMI 2.0 with HP TopTools. Online documentation. OmniBook Recovery CD included. Centralized worldwide BIOS and driver update service.
  • Page 133 Specifications and Regulatory Information CPU: Intel Mobile Pentium or Pentium II. South Bridge: PIIX4. Video: NeoMagic NM2160 (NMG4). Audio: Crystal CS4237B. CardBus: TI PCI1220. Keyboard controller: National PC87570. Super I/O: SMC 669FR.

  • Page 134: Software System Resources

    Specifications and Regulatory Information Software System Resources Below are default values for the system resources. To see other, non-default possibilities, refer to the BIOS Setup utility, which lists port and audio device configurations in the System Devices menu. The tables in this section show typical resource usage as set up by the OmniBook BIOS.
  • Page 135 Specifications and Regulatory Information Valid uses for memory addresses CC000-DBFFF: Upper memory blocks (UMBs). PC Card memory windows. 170-177 Secondary HDD controller (internal CD-ROM) 1F0-1F7 Internal hard disk 220-22F Crystal sound Secondary HDD controller (internal CD-ROM) 378-37F LPT1 (printer port) 388-38B Sound 3B0-3BB...

  • Page 136: Safety Information

    To purchase a power cord (including one for a country not listed below) or a replacement ac adapter (HP part number F1454A), contact your local Hewlett-Packard dealer or Sales and Service office.
  • Page 137 When discarding a battery pack, contact your local waste disposal provider regarding local restrictions on the disposal or recycling of batteries. To obtain a replacement battery, contact your local dealer or HP sales office. Do not charge the battery if the ambient temperature exceeds 45 °C...
  • Page 138 EN60825-1). This device is not considered harmful, but the following precautions are recommended: Ensure proper use by reading and following the instructions carefully. If the unit requires service, contact an authorized HP service center—see the OmniBook Support and Service booklet. Do not attempt to make any adjustment of the unit.

  • Page 139: Regulatory Information

    Specifications and Regulatory Information Regulatory Information This section presents information that shows how the OmniBook complies with regulations in certain regions. Any modifications to the OmniBook not expressly approved by Hewlett-Packard could void the authority to operate the OmniBook in these regions.

  • Page 140: Canada

    (415) 857-1501 declares that the product(s) Hewlett-Packard Company HP OmniBook 2100/3100 Complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.

  • Page 141: Europe

    Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC, and carries the EC mark accordingly. The HP F1454A ac adapter used with this product is designed to operate on all power systems, other than IT power systems. [1] The product was tested in a typical configuration with Hewlett-Packard personal computer peripherals.
  • Page 143 3-9 SmartCard, 1-4 overheated, 3-4 Zip drive, 4-7 replacement, 8-9 address safeguards, 3-2 Hewlett-Packard, 8-2 safety, 3-7 HP website, 1-2 saving power, 3-9 Input/Output, 8-7 secondary, 3-9 Advanced Power Management (APM) troubleshooting, 7-13 features, 3-2 BIOS optimizing battery life, 3-9 resources, 8-6 Windows NT 4.0, 6-20...
  • Page 144 cursor (pointer), 2-5 System Devices menu, 1-12 Boot menu (BIOS), 1-15 default values, 8-6 cable deleting password, 2-18, 3-10 floppy drive, 4-5 destop management, 1-16 power, 1-3 devices Card Executive, 6-21 anti-static, 5-6 cards. See PC Cards boot order, 1-15 CD-ROM drive conflicts, 1-10 inserting CD, 4-6...
  • Page 145 docking factory installed operating systems, 1-8, 6-3 products, 4-17 FAT32, 6-2 tray, 4-17 FDD controller, 1-12 documentation, 1-2 files dot matrix printer, 4-11 infrared transfer, 4-14 dragging items, 2-5 protecting, 2-20 drive recovering, 6-2 CD-ROM, 4-6 floppy disk drive floppy disk, 4-5 connecting externally, 4-5 status icons, 2-15 inserting/removing disk, 4-5...
  • Page 146 2-10 HP applications, 6-23 Kensington lock, 2-19 keyboard embedded keypad, 2-11 icons Fn hot keys, 2-10 drive, 2-15 non US, 2-12 keyboard, 2-15 num lock, 2-11 power, 2-14 numeric keypad, 2-10 IDE controller, 1-12 status icons, 2-15 infrared...
  • Page 147 mouse pointing device PS/2, 4-11 external, 4-11 serial, 4-11 settings, 2-6 moving the pointer using, 2-5 touch pad, 2-5 port replicator troubleshooting, 7-3 USB ports, 4-12 notice (legal), ii ports external devices, 4-9 locations, 1-5 power button, 1-5, 2-3 Advanced Power Management, 3-2 status lights, 2-13 button, 1-5 OmniBook...
  • Page 148 8-9 serial mouse, 4-11 regulatory information, 8-11 service reinstalling booklet, 1-2, 1-3 HP applications, 6-23 HP service center, 8-10 OmniBook BIOS, 6-24 setting up Windows 95, 6-4 McAfee VirusScan, 2-18 Windows NT 4.0, 6-5 OmniBook BIOS, 1-10 removing...
  • Page 149 stopping OmniBook, 2-3 performance, 7-12 support, 8-10 port replicator, 7-3 support utility disk, 5-5, 6-2 power, 7-13 suspend printing, 7-15 and display life, 2-7 serial device, 7-16 hot keys, 2-10 startup, 7-17 mode, 2-3, 2-10 universal serial bus (USB), 7-16 on undock, 1-14 Zip drive, 7-4 status lights, 2-13...
  • Page 150 video drivers, 6-9 Card Executive, 6-21 Windows keys, 2-11 installing, 6-16 Windows NT 4.0 video drivers, 6-18 documentation, 1-2 Working in Comfort, 8-9 factory build, 6-5 setting up, 1-8 Zip disk, 4-7 Windows NT 4.0 (retail) zoomed video, 4-15, 8-4 APM drivers, 6-20 audio drivers, 6-19 Index-8...

This manual is also suitable for:

Omnibook 3100

Table of Contents