Denon AVR-990 Owner's Manual page 37

Setting items
Bass Setting Subwoofer Mode : Select low range signals to be reproduced by
subwoofer.
Settings for subwoofer and
LFE signal range playback. • LFE : The low range signal of the channel set to "Small" speaker size is
added to the LFE signal output from the subwoofer.
• LFE+Main : The low range signal of all channels is added to the LFE
signal output from the subwoofer.
• This can be set when "Speaker Configuration" – "Subwoofer" (vpage
33) is set to "Yes".
• Play music or a movie source and select the mode offering the strongest
bass.
• Select "LFE+Main" if you want the bass signals to always be produced
from the subwoofer.
LPF for LFE : Set LFE signal playback range.
• 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz
Distance Unit : Set the unit of distance.
• Feet
Set distance from listening
position to speakers. • Meters
Measure beforehand the
Step : Set the minimum variable width of the distance.
distance from the listening
• 1ft / 0.1ft
position to each speaker.
• 0.1m / 0.01m
Front L / Front R / Center / Subwoofer / Surround L / Surround R /
S. Back L z / S. Back R z / Front Height L / Front Height R : Select the
speaker.
z: When the "Speaker Configuration" – "Surround Back" setting
(vpage 33) is set to "1spkr", "S. Back" is displayed.
• 0.0ft ~ 60.0ft / 0.00m ~ 18.00m : Set the distance.
• Speakers set to "None" in "Speaker Configuration" (vpage 33) are
not displayed.
• The speakers that can be selected differ depending on the "Amp Assign"
(vpage 33) and "Speaker Configuration" (vpage 33) settings.
• Default settings :
Front / Center / Subwoofer / Front Height : 12.0 ft (3.60 m)
Surround / Surround Back : 10.0 ft (3.00 m)
• Set the difference in the distance between the speakers to less than 20
feet (6.0 meters).
Default : Reset all distance settings to factory default.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
When you select "Default" and press
prompt is displayed. Select either "Yes" or "No", and press
Remote control operation
buttons
Setting contents
ENTER
, the "Default Setting?"
:Displaying the menu :Moves the cursor
Cancel the menu (Up/Down/Left/Right)
Setting items
Channel Level Test Tone Start : Output test tone.
•
Set the volume of the test
tone to be the same when it
is output from each speaker.
z : When the "Speaker Configuration" – "Surround Back" setting
•
•
•
•
•
Default : Reset all channel level settings to factory default.
•
•
Crossover Frequency 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz : Set the crossover frequency.
Outputs at below set
frequency, each speaker's
Advanced : Specify crossover frequency for each speaker.
bass signal output from
•
the subwoofer. Set this
according to the low
•
frequency reproduction
capabilities of the speakers
you are using.
•
•
•
•
ENTER
.
:Confirm the setting
Making Detailed Settings (Manual Setup)
Setting contents
Front L / Front Height L / Center / Front Height R / Front R / Surround
R / S. Back R z / S. Back L z / Surround L / Subwoofer : Select the
speaker.
(vpage 33) is set to "1spkr", "S. Back" is displayed.
–12.0dB ~ +12.0dB (0.0dB) : Adjust the volume.
Speakers set to "None" in the "Speaker Configuration" (vpage 33)
settings are not displayed.
When o is pressed while the subwoofer volume is set to "–12 dB", the
"Subwoofer" setting switches to "OFF".
When a headphones jack is inserted in the PHONES terminal of the AVR-
990, the "Channel Level" is not displayed.
[CHANNEL LEVEL]
You can also press to set (vpage 77 "Adjust the
Volume of the Different Speakers").
Yes : Reset to the defaults.
No : Do not reset to the defaults.
Front / Center / Surround / Surround Back / Front Height : Select the
speaker.
40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz /150Hz / 200Hz /
250Hz : Set the crossover frequency.
Can be set when the "Speaker Configuration" – "Subwoofer" (vpage
33) setting is "Yes", or when you have a speaker that is set to "Small".
Always set the crossover frequency to "80 Hz". When using small
speakers, however, we recommend setting the crossover frequency to
a higher frequency.
For speakers set to "Small", sound below the crossover frequency is cut
from the sound output. The cut bass sound is output from the subwoofer
or front speakers.
The speakers that can be set when "Advanced" is selected differ
according to the "Subwoofer Mode" setting (vpage 34).
• When "LFE" is selected, speakers set to "Small" at "Speaker
Configuration" can be set. If the speakers are set to "Large", "Full
Band" is displayed and the setting cannot be made.
• If set to "LFE+Main", this setting can be made regardless of the
speaker size.
:Return to previous menu
ENGLISH
See overleaf