Speaker Installation Option; Troubleshooting Guide - Panasonic SABTT268 Owner's Manual

Speaker installation
Optional speaker settings
option
Attaching to a wall
You can attach all of the speakers (except subwoofer) to a wall.
≥ The wall or pillar on which the speakers are to be attached
should be capable of supporting 10 kg (22 lbs) per screw.
Consult a qualified building contractor when attaching the
speakers to a wall. Improper attachment may result in
damage to the wall and speakers.
≥ Do not attempt to attach these speakers to walls using
methods other than those described in this manual.
1
Drive a screw (not supplied) into the wall.
A At least 30 mm (1
B ‰ 4.0 mm ( /
5 q)
32
C ‰ 7.0 mm to ‰ 9.4 mm
( / q to /
9 3 q)
32 8
D Wall or pillar
E 5.5 mm to 7.5 mm
( / q to /
7 5 q)
32 16
2
Fit the speaker securely onto the screw(s)
with the hole(s).
DO NOT
≥ In this position, the
speaker will likely fall if
moved to the left or right.
Use the measurements indicated below to identify the
screwing positions on the wall.
≥ Leave at least 20 mm (
10 mm ( 13 / q) on each side to allow enough space for fitting
32
the speaker.
Front speaker,
Surround speaker
F 40 mm (1 /
9 q)
16
G 17.6 mm ( 11 / q)
16
H 98.7 mm (3 7 / q)
8
Center speaker
I 23 mm ( /
29 q)
32
J 95 mm to 97 mm
(3 / q to 3 /
3 13 q)
4 16
K 26 mm (1 /
1 q)
32
L 16.7 mm ( /
21 q)
32
M 63.7 mm (2 /
1 q)
2
VQT3M40
36
/
3 q)
16
e.g., Front speaker
DO
≥ Move the speaker so that
the screw is in this
position.
/ q) of space above the speaker and
25
32

Troubleshooting guide

Reference
Before requesting service, please perform the
following steps.
Do you have the latest firmware installed?
Firmware updates may be released to correct operating
irregularities that are discovered with certain movies. (
Make the following checks and visit our
website for more information.
http://www.panasonic.com/help
Enter the model number.
Or visit our website to find a service
center.
You can find a service center near you easily on our website.
Other support information:
"Customer Services Directory (United States and Puerto
Rico)" ( 43)
The following do not indicate a problem with this unit:
jRegular disc rotating sounds.
jImage disturbance during search.
jImage disturbance when replacing 3D discs.
∫ Unit does not respond to the remote
control or front panel buttons.
Press and hold [POWER Í/I] on the main unit for 5 seconds.
jIf still unable to power the unit off, disconnect the power cord,
wait 1 minute, then reconnect the power cord.
∫ Cannot eject disc.
The unit may have a problem.
While the unit is off, press and hold [9] on the remote
control and [< OPEN/CLOSE] on the unit at the same time for
more than 5 seconds.
General operation
To return to the factory preset
≥ Select "Yes" in "Restore Default Settings" in the Setup menu.
( 34)
To return all settings to the factory preset
≥ Reset the unit as follows:
While the unit is off, press and hold [+ VOLUME], [< OPEN/
CLOSE] and [POWER Í/I] on the main unit at the same
time for more than 5 seconds.
The remote control doesn't work properly.
≥ Change the batteries in the remote control. (
≥ The remote control and main unit are using different codes. If
"SET " is displayed on the unit's display when a button is
pressed on the remote control, change the code on the
remote control. ( 34)
Disc cannot be played.
≥ The disc is dirty. ( 9)
≥ Check the region code.
17)
4
4
9)