Advertisement
Controller
Item
Output type
(*1)
Measurement cycle
Samples to average
(*3)
Analog output
Timing input, bank switching input,
zero reset input, reset input
HIGH/PASS/LOW
(*5)
Judgment output
(*6)
Sync output
Indicator
Main
Number of registered
functions
setups
Measurement Mode
Display during
measurement
Zero reset functions
Hold
Timer functions
Adjustment functions
Calculation
Other
Temperature characteristic
Current consumption
Power supply voltage
Dielectric strength
Insulation resistance
Ambient temperature
Ambient humidity
Vibration resistance(durability)
Degree of protection
Cable length
Material
Weight (packed state)
Accessories
*1:
The first response time is "measurement cycle x (number of samples to average setting + 1) + 1 ms" max. For the second response time onwards, the specified measurement cycle time is
output.
*2:
The response time in the high-speed mode (FAST) for the IC lead pitch and IC lead width judgment modes is 1 ms.
*3:
Current/voltage can be switched using the switch provided on the rear of the Controller.
*4:
Can be set by the analog output scaling function.
*5:
The error (ERR) state is displayed when all HIGH/PASS/LOW outputs turn OFF.
*6:
Normally, wire the sync output wire directly to the emitter's sync input wire and run the Controller in the standard mode. On an NPN type Controller, use an NPN type emitter, and on a PNP
type Controller, use a PNP type emitter. Wiring of the sync wires is not required when the Controller is run in the high-speed mode.
(Note, however, that the Controller becomes more susceptible to the influence of ambient light in this case.)
ZX-GT
ZX-GTC11
NPN
1.5 ms (standard mode (NORM))
0.5 ms (high-speed mode (FAST))
1/2/4/8/16/32/64/128/256/512/1024/2048/4096
For current output: 4 to 20 mA/F.S., max. load resistance 300 Ω
For voltage output: ±4 V, (±5 V, 1 to 5 V
ON: short-circuited with 0V or 1.5V max.
OFF: Open (leakage current: 0.1 mA max.)
NPN open-collector output
30 VDC 50 mA max.
Residual voltage 1.2 V max.
Judgment output indicator: HIGH (orange), PASS (green), LOW (orange)
Main display (red) Sub-display (yellow) Bank 1/2 (orange), zero reset (green)
2 banks
Interrupted beam width measurement, incident beam width measurement, outer diameter measure-
ment, center position measurement, IC lead pitch, IC lead width judgment, specified edge measurement,
wire position measurement, glass edge position measurement
Measured value, resolution, threshold, voltage output value, current output value (number of display dig-
its can be changed)
Offset setting of zero reset value, zero reset value memory
Sample hold, peak hold, bottom hold, peak-to-peak hold, average hold, delay hold
ON delay, OFF delay, one-shot
Optical Axis adjust mode/light intensityt writing mode, variable binary level, variable edge filter, analog
output scaling
2 Possible on up to two Controllers (Calculation Unit ZX-CAL2 is required for connecting Controllers to
each other.) A-B, A+B, width
Measurement cycle setting, threshold setting, hysteresis setting, initialization, key lock
±0.005%F.S./°C
150 mA max. (including receiver)
24 VDC +10%, -15% ripple (p-p) 10% max.
1,000 VAC, 50/60 Hz for min
20 MΩ (at 500 VDC megger)
Operating: 0 to +50°C Storage: -15 to +60°C (with no icing or condensation)
Operating and storage: 35 to 85% (with no condensation)
10 to 150 Hz Single-amplitude: 0.35 mm for 80 min each in X, Y and Z directions
IEC60529 IP20
2 m
Case: PBT (polybutylene terephthalate), Cover: Polycarbonate
Approx. 330 g
Instruction Sheet
PNP
(*2)
), output impedance 100 Ω
(*4)
ON: short-circuited with power supply voltage or
power supply voltage -1.5V max.
OFF: Open (leakage current: 0.1 mA max.)
PNP open-collector output
30 VDC 50 mA max.
Residual voltage 2 V max.
ZX-GTC41
3
Advertisement
