Advertisement
Precautions
!WARNING
Do not touch any of the terminals while the power is being sup-
plied.
Doing so may result in electric shock.
■ General Precautions
Be sure to observe these precautions to ensure safe use.
• Do not use the product in places where explosive or flammable
gases may be present.
• Never disassemble, repair or modify the product.
• Tighten the terminal screws properly.
• Use the specified size of solderless terminals for wiring.
• Use the product within the rated supply voltage.
• Use the product within the rated load.
• The life expectancy of the output relay varies considerably accord-
ing to its switching capacity and operating conditions. Be sure to
use the output relay within its rated load and electrical life expect-
ancy. If the output relay is used beyond its life expectancy, its con-
tacts may become fused or burned.
■ Correct Use
If you remove the Controller from its case, never touch nor apply
shock to the electronic parts inside.
Do not cover the E5@K-T. (Ensure sufficient space around the Con-
troller to allow heat radiation.)
Do not use the Controller in the following places:
• Places subject to icing, condensation, dust, corrosive gas (espe-
cially sulfide gas or ammonia gas).
• Places subject vibration and large shocks.
• Places subject to splashing liquid or oil atmosphere.
• Places subject to intense temperature changes.
• Places subject to heat radiation from a furnace.
Be sure to wire properly with correct polarity of terminals.
When wiring input or output lines to the Controller, keep the following
points in mind to reduce the influence from inductive noise:
• Allow adequate space between the high voltage/current power
lines and the input/output lines.
• Avoid parallel or common wiring with high voltage sources and
power lines carrying large currents.
• Using separating pipes, ducts, and shielded line is also useful in
protecting the Controller, and its lines from inductive noise.
Cleaning: Do not use paint thinner or organic solvents. Use standard
grade alcohol to clean the product.
Use a voltage (100 to 240 VAC at 50/60 Hz, or 24 VDC). At power
ON, the prescribed voltage level must be attained within two sec-
onds.
Allow as much space as possible between the Controller and devices
that generate a powerful high frequency (high-frequency welders,
high-frequency sewing machines, etc.) or surge. These devices may
cause malfunctions.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Cat. No. H087-E1-03
I-128
Digital Controller
In the interest of product improvement, specifications are subject to change without notice.
E5CK-T
If there is a large power-generating peripheral device and any of its
lines near the Controller, attach a surge suppressor or noise filter to
the device to stop the noise affecting the Controller system. In partic-
ular, motors, transformers, solenoids and magnetic coils have an
inductance component, and therefore can generate very strong
noise.
When mounting a noise filter on the power supply to the Controller,
be sure to first check the filter's voltage and current capacity, and
then mount the filter as close as possible to the Controller.
Use within the following temperature and humidity ranges:
• Temperature: –10 C to 55 C (with no icing or condensation)
Humidity: 35% to 85% (with no icing or condensation)
If the Controller is installed inside a control board, the ambient tem-
perature must be kept to under 55 C, including the temperature
around the Controller.
If the Controller is subjected to heat radiation, use a fan to cool the
surface of the Controller to under 55 C.
Store within the following temperature and humidity ranges:
• Temperature: –25 C to 65 C (with no icing or condensation)
Humidity: 35% to 85% (with no icing or condensation)
Never place heavy objects on, or apply pressure to the Controller
that may cause it to deform and deteriorate during use or storage.
Avoid using the Controller in places near a radio, television set, or
wireless installing. These devices can cause radio disturbances
which adversely affect the performance of the Controller.
Mounting
The dimensions of the Digital Controller conform to DIN 43700.
Recommended panel thickness is 1 to 8 mm (1 to 5 mm for E5CK).
Mount the Unit horizontally.
Connection
To reduce inductive noise influence, the lead wires connecting the
input type to the Digital Controller must be separated from the power
lines and load lines.
Use the specified compensating conductors for thermocouples. Use
lead wires having a small resistance for platinum resistance ther-
mometers.
Connection Example
Wire the terminals of the Unit using solderless terminals.
The tightening torque applied to the terminal screws of the Unit must
be approximately 0.78 N·m or 8 kgf·cm.
Use the following type of solderless terminals for M3.5 screws.
7.2 mm max.
7.2 mm max.
Advertisement
