Specifications - Omron E3F2-SUS Datasheet

Specifications

Ratings
Item
Sensing method
Power supply voltage
Current consumption
Sensing distance
Standard object
Directional angle
Differential travel
(hysteresis)
Black/white error
Response time
Control output
Power reset time
Ambient illumination
Ambient temperature
Ambient humidity
Insulation resistance
Dielectric strength
Vibration resistance
Shock resistance
*1
Degree of protection
Light source (wave length)
Indicators
Sensitivity adjustment
Connection method
Operation mode
Weight Pre-wired (2 m)
(approx.)
Connector
Circuit protection
Material Lens
Housing
*1.
The IP69k test according to DIN 40 050 part 9 is intended to simulate high pressure/steam cleaning. During the test 14-16l/min water at 80°C is sprayed onto the
sensor from different angles with 8000-10000kPa. The sensor may not suffer any damaging effects from high pressure water in appearance and functionality.
*2.
Material-specification for stainless steel housing case: 1.4305 (W.-No.), 303 (AISI), 2346 (SS). For other stainless steel materials please contact your OMRON
sales representative.
E3F2-SUS
#
E3F2-7 E3F2-R4
Through-beam Retro-reflective
10 to 30 V DC
50 mA max. 30 mA max.
7 m 0.1 to 4 m
(with E39-R1S)
Opaque: Opaque:
11 mm dia. min. 56 mm dia. min.
3° to 20° 3° to 20°
–
–
Operation and Re- 1 ms max
set:
2.5 ms max.
Transistor (open collector), load current: 100 mA max. (residual voltage: 2 V max.)
50 ms 100 ms max.
Incandescent lamp:3000 lx max. / Sunlight:10000 lx max.
Operating: -25 to 55 °C / Storage: -30 to 70 °C (with no icing or condensation)
Operating: 35% to 85% / Storage: 35% to 95% (with no condensation)
20 MΩ min. at 500 V DC between energized parts and case
1000 VAC max., 50 / 60 Hz for 1 min between energized parts and case
10 to 55 Hz, 1.5 mm double amplitude for 2 hrs each direction (X, Y, Z)
2
Destruction: 500 m/s each direction (X, Y, Z)
IEC 60529 IP67, IP69K after DIN 40050-9
Infrared LED Red LED (660 nm) Infrared LED (880 nm)
(950 nm)
Light Light incident (red) /
incident / power in- stability (green)
dicator for light
source (red)
Fixed Adjustable
2 m, 5 m pre-wired cable (PVC, dia. 4 mm (18 / 0.12)) or M12-connector
Light-ON or Dark-ON selectable by wiring
180 g 90 g
120 g 50 g
Output short-circuit and power supply reverse polarity
PMMA
*2
Stainless steel
# # #
- E3F2-DS10
Diffuse-reflective
Wide beam (fixed)
25 mA max.
0.1 m
(5 x 5 cm white
mat paper)
–
–
20% max.
2.5 ms max.
50 ms
Light incident / power indicator for light
source (red)
Fixed
#
E3F2-DS30 E3F2-LS10
Potentiometer Background
adjustment suppression
30 mA max.
0.3 m 0.1 m
(10 x 10 cm white (10 x 10 cm white
mat paper) mat paper)
5% max
3% max
1 ms max.
100 ms
Red LED (660 nm)
Output
indicator
(orange) / stability
(green)
Adjustable Fixed
# #
4-
3