Ratings And Specifications - Omron F3W-D Installation Manual

Ratings and Specifications

Sensing method
Item
Sensing distance
Beam gap
Number of beams
Sensing width
Standard sensing object Opaque, 35 mm dia. min.
Light source
(emission wavelength)
Power supply voltage
Power consumption
Control output
Picking instruction
indicator input
Protection circuits
Response time
Indicators
Ambient temperature
Ambient humidity
Insulation resistance
Dielectric strength
Vibration resistance
(destruction)
Shock resistance
(destruction)
Degree of protection
Connection method
Weight (packed state)
Materials
Accessories
*1. The F3W-D052@P Emitters are provided with the external picking indicator output line shown in the following table.
Item
Connection method
Electrical specifications
*2. Response time includes transfer delay time.
*3. The transmission indicator indicates bus transmission status.
*4. The following cable lengths are also available.
F3W-D052A (P): 2 m, 7 m
F3W-D052B (P): 1 m, 3.5 m
Downloaded from Elcodis.com electronic components distributor
Model F3W-D052A (P) *1
3 m, switchable between LONG mode (1 to 3 m) and SHORT mode: (0.05 to 1 m), factory-set to SHORT mode.
25 mm
5
100 mm
Infrared LED (860 nm)
12 to 24 VDC±10% (ripple (p-p): 10% max.)
Emitter: 0.6 W max., Receiver: 0.7 W max.
NPN open collector with 100 mA max. at 30 VDC
NPN open collector output type
Dark-ON or Light-ON (selectable)
Open collector with relay or transistor input
Indicator ON: Input voltage of 0 to 2 V
Indicator OFF: Open (with leakage current of 0.1 mA max.)
Reverse-connection protection, output short protection, and mutual interference prevention function
(set with frequency switch)
Operate/Reset: 10 ms max.
Operation indicator (orange), stability indicator (green), and 6 picking indicators (orange),
Receiver
UNI-WIRE Direct Connection Models: Transmission indicator (orange) *3
Power indicator (green), different frequency indicator (green), and 6 picking indicators (orange),
Emitter
UNI-WIRE Direct Connection Models: Transmission indicator (orange) *3
Operating: −10° to 55°C, Storage: −25° to 70°C (with no icing or condensation)
35% to 85% (with no condensation)
20 MΩ min. (at 500 VDC)
1,000 VAC 50/60 Hz for 1 min
10 to 50 Hz, 1.5-mm double-amplitude for 2 hours each in X, Y and Z directions
2
500 m/s , 3 times each in X, Y and Z directions
IEC60529: IP62 (with the operation cover closed)
Pre-wired
Standard cable length: 5 m *4
Approx. 360 g
Case,
indicator ABS resin
windows
Lens Acrylic resin
Opera-
tion Nylon (PA6)
cover
Instruction manual
F3W-D052AP, F3W-D052BP, F3W-D052UP
Pre-wired (standard cable length: 300 mm)
Output current: 50 mA max.
Output voltage: Fixed at Sensor power supply voltage
http://www.ia.omron.com/
Through-beam
F3W-D052B (P) *1
Pre-wired connector
(M12 5-pin connector)
Standard cable length: 2 m *4
Approx. 230 g
4
(c)Copyright OMRON Corporation 2008 All Rights Reserved.
F3W-D
F3W-D052U (P) *1
24 VDC ±10%, ripple (p-p) 10% max.
(supplied by UNI-WIRE SYSTEM,
other power supply also possible)
Emitter/Receiver: 0.6 W max.
Transmission output
(output address set using DIP switch 3
control output address setting switch)
Transmission input
(input address set using DIP switch 2
instruction input address setting
switch)
Operate/release: 39 ms (64-bit), 66 ms
(128-bit), or 120 ms (256-bit) max.*2
Pre-wired
Standard cable length: 2 m
Approx. 220 g
4