Advertisement
1-conduit Models
Adjustable Roller Lever, Form Lock
(with Metal Lever, Resin Roller)
D4N-1@2G
D4N-2@2G
D4N-3@2G
D4N-4@2G
D4N-9@2G (See note 2.)
17.5 dia. × 6.8
resin roller
18
9
± 0.2
2.5
47
± 0.2
55
20
± 0.1
22
± 0.1
22
± 0.2
31 max.
Note: 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
2. Refer to following diagrams for details on M12 connectors.
Snap-action (1NC/1NO) (2NC), Slow-action (2NC) (3NC)
Model
OF max.
RF min.
PT
OT min.
MD max. (See note 3.)
OP
TT (See note 4.)
DOT min. (See note 5.)
DOF min. (See note 5.)
Slow-action (1NC/1NO) (2NC/1NO)
Model
OF max.
RF min.
PT (See note 2.)
PT (2nd) (See note 3.)
PT (See note 4.)
PT (2nd) (See note 5.)
OT min.
OP
TT (See note 6.)
DOT min.
DOF min. (See note 7.)
1-conduit M12 Connector
D4N-9@@@
(14)
M12 × 1
D4N
45
± 1
39.5
± 1
(31)
11
± 0.2
20 to 66R
20.5 × 20.5
27.5
21.5
2.15±0.05R
mounting holes
Conduit cap
14.2
+0.15
dia. holes
Two, 4
30
0
Depth: 5
D4N-@12H
D4N-@12G
D4N-@22H
D4N-@22G
D4N-@B2H
D4N-@B2G
D4N-@D2H
D4N-@D2G
(See note 2.)
4.5 N
0.4 N
18° to 27°
40°
14°
---
(80° )
50°
20 N
D4N-@A2H
D4N-@A2G
D4N-@C2H
D4N-@C2G
D4N-@E2H
D4N-@E2G
D4N-@F2H
D4N-@F2G
(See note 1.)
4.5 N
0.4 N
18° to 27°
(44° )
27.5° to 36.5°
(18° )
40°
---
(80° )
50°
20 N
14.2
30
Adjustable Roller Lever, Form Lock
(with Metal Lever, Rubber Roller)
D4N-1@2H
D4N-2@2H
D4N-3@2H
D4N-4@2H
D4N-9@2H (See note 2.)
Bearing
18
±0.2
9
2.5
± 0.2
47
55
20
± 0.1
22
± 0.1
22
± 0.2
31 max.
Note: 1. Variation occurs in the simultaneity of contact opening/clos-
ing operations of 2NC, 2NC/1NO, and 3NC contacts. Check
contact operation.
2. The operating characteristics of these Switches were mea-
sured with the roller lever set at 32 mm.
3. Only for snap-action models.
4. Reference value.
5.
Only for slow-action models. For safe use, always make
!
sure that the minimum values or greater are provided.
Note: 1. The operating characteristics of these Switches were mea-
sured with the roller lever set at 32 mm.
2. This PT value is possible when the NC contacts are open
(OFF).
3. This PT value is possible when the NO contacts are closed
(ON).
4. Only for MBB models.
5. Reference value for MBB models only.
6. Reference value.
7.
For safe use, always make sure that the minimum
!
values or greater are provided.
48.2
±1
±1
41.3
50 dia. × 8
(29.2)
rubber roller
±0.2
11
32 to 66R
20.5×20.5
27.5
21.5
2.15±0.05R
mounting holes
Stainless steel
lever
14.2
Conduit cap
30
+0.15
Two, 4
dia. holes
0
Depth: 5
G-231
Advertisement
