Table of Contents
Advertisement
Installation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance
Troubleshooting
Service
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dispensing Valve Parts Drawing
Pumps Parts Lists
Technical Data
Warranty
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graco Information
1. Apply thread sealant to the male threads of the
bushing (20g) and install the air regulator (20) at
the pump air inlet. See Fig 1.
2. Apply thread sealant to the male threads of the
elbow (11) and install the dispense valve assembly
at the pump outlet. See Fig 1.
3. Install the pump in the bung hole of a fluid supply
container. Screw the bung adapter (A) tightly into
the hole. Raise the pump about1/2 inch (12 mm)
from the bottom of the container. Tighten the bung
adapter screw. See Fig 1.
2
307637
Table of Contents
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation
Fluid and Solvent Compatibility
WARNING
To reduce the risk of component rupture, which can
result in serious bodily injury, all fluids used in this
pump must be chemically compatible with the wetted
parts shown on page 8. Consult your fluid supplier to
ensure compatibility.
Do not use 1,1,1-trichloroethane, methylene chlo-
ride, other halogenated hydrocarbon solvents or
fluids containing such solvents in this equipment,
which contains aluminum and/or zinc parts. Such use
could result in a serious chemical reaction, with the
possibility of explosion, which could cause death, se-
rious bodily injury and/or substantial property dam-
age.
2
2
2
4
4
5
6
7
8
8
Advertisement
Table of Contents
