Sony HCD-SHAKE33 Service Manual page 80

HCD-SHAKE33/SHAKE44/SHAKE55/SHAKE66/SHAKE77/SHAKE88
Ver. 1.1
Pin No. Pin Name
55 SSI1_DI
56 PCONT-BTSTBY
PCONT-PSAVE-PRO-
57
TECT
58 Vcc
59 LINK-DET
60 NFC-DATA
61 Vss
62 PVcc
63 AC-CUT
64 DEBUG-RxD
65 BT-RxD
66 SS-DET
67 RTC-X1
68 RTC-X2
69 PLLVcc
70 EXTAL
71 XTAL
72 Vss
73 Vss
74 NMI
75 Vss
76 RES
77 PVcc
78 AMP-TEMP-MON
79 SPM-C-MON
80 SPM-AMBIENT-TEMP
81 MODEL-DEST-IN
82 INT-FAN-DET
83 MASTER-VOLUME
84 AD-KEY0
85 AD-KEY1
86 AVcc
87 AVss
88 AVref
89 BSCANP
90 PVcc
91 AUDIO-X1
92 AUDIO-X2
93 Vss
94 /LINE-MUTE
95 Vcc
96 /LINE-MUTE-FR
97 TRST
98 TDO
99 TDI
100 TMS
101 TCK
102 Vss
103 TEST-MON0/SD_D2_0
104 TEST-MON1/SD_D3_0
105 Vcc
TEST-MON2/SD_
106
CMD_0
107 Vss
108 TEST-MON3/SD_CLK
80
I/O
I Data In Signal from ADC to Aragon
O BT Standby Power Control Pin. "H": ON
O Main power on/off control signal output "H":power on
- Power supply terminal (+3.3V)
I Party chain input bias detection pin
I Two-way data bus with the NFC
- Ground terminal
- Power supply terminal (+3.3V)
I AC off detection signal input from the reset signal IC "L": AC Cut detected
I RxD (for Debug)
I RX input signal from Bluetooth section
I Speaker detection pin. "L": Speaker detected
- Not used
- Not used
- Power supply terminal (+3.3V)
- Not used
- Not used
- Ground terminal
- Ground terminal
- Non-maskable interrupt input terminal
- Ground terminal
- Reset signal
- Power supply terminal (+3.3V)
I Temperature protect pin. "L": Protect on
I Voice coil temperature monitor pin.
I Ambient temperature monitor pin.
I Model and Destination setting terminal (A/D input)
I Fan speed detection pin
I Jog dial pulse input from the MASTER VOLUME encoder (A/D input)
I Key input terminal (A/D input)
I Key input terminal (A/D input)
- Power supply terminal (+3.3V)
- Ground terminal
- A/D Converter reference voltage input terminal (+3.3V)
- Boundary scan setting pin
- Power supply terminal (+3.3V)
- Not used
- Not used
- Ground terminal
O Muting Control Switch for Party Chain. "L": mute On
- Power supply terminal (+3.3V)
O Muting Control Switch for Speaker. "L": mute On
- Debugging interface: Initialization-signal input pin.
- Debugging interface: Serial output pin for instructions and data.
- Debugging interface: Serial input pin for instructions and data.
- Debugging interface: Test-mode select signal input pin
- Debugging interface: Test-clock input pin
- Ground terminal
O Test port for software checking.
O Test port for software checking.
- Power supply terminal (+3.3V)
O Test port for software checking.
- Ground terminal
O Test port for software checking.
Description