Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Stihl iMOW 5.0 EVO
Summary of Contents for Stihl iMOW 5.0 EVO
- Page 1 iMOW® 5.0 EVO, 6.0 EVO, 7.0 EVO 2 - 46 Instruction Manual...
-
Page 2: Table Of Contents
► Serious or fatal injuries can be avoided by tainable and responsible handling of natural taking the precautions mentioned. resources. This user manual is intended to help you use your STIHL product safely and in an environmentally friendly manner over a long service life. 0458-012-0101-A... -
Page 3: Overview
3 Overview English 7 Rear grip surface NOTICE Lift and transport the robot mower by simulta‐ ■ This notice refers to risks which can result in neously gripping it at the front and rear grip damage to property. surface. ► Damage to property can be avoided by tak‐ 8 Protective strip ing the precautions mentioned. - Page 4 English 3 Overview Mowing unit 7 LED The LED indicates the status of the docking station. 8 Charging contacts The charging contacts connect the docking station with the robot mower. 9 Base plate The base plate is the base for the docking station.
-
Page 5: Safety Precautions
1 LED lights up red. The battery is too Intended Use warm or too cold. ® The STIHL iMOW 5.0 EVO, 6.0 EVO, 7.0 EVO 4 LEDs flash red. There is a fault in the robot mower is designed for mowing and mulch‐... - Page 6 ► Use the robotic mower with the STIHL AAI – The user is not under the influence of installed battery. alcohol, medication or drugs.
- Page 7 This may result in serious injury to bystanders, The battery has been installed in the robot children and animals and damage to property. mower and must only be removed by a STIHL ► Keep bystanders, children and ani‐ authorized dealer.
- Page 8 ► Disconnect the power supply before a ► Replace worn or damaged labels. storm or when there is a risk of a lightning ► If you are unsure: Consult a STIHL author‐ strike. ized dealer. ■ People can trip over the docking station, charging cable, power supply or connecting 4.6.2...
- Page 9 The battery has been installed in the robot – The docking station, charging cable, power mower and must only be removed by a STIHL supply, connecting cable and plug connections authorized dealer. are undamaged.
- Page 10 ► Press the STOP pushbutton and activate – The mains plug of the connecting cable or the device lock. Contact a STIHL author‐ extension cord is damaged. ized dealer. – The socket is not properly installed. ■ If the blades hit a foreign object during the...
- Page 11 The battery has been installed in the robot to property. mower and must only be removed by a STIHL ► Route the wires and charging cable so that authorized dealer. they are outside of the mowing area.
- Page 12 ► Wind up the connecting cable and attach it The battery has been installed in the robot to the power supply. mower and must only be removed by a STIHL ► Grip the power supply by the housing and authorized dealer.
-
Page 13: Description Of Operation
(3), it will slow down and then continue to supply require servicing or repairs: Contact move in a different direction. a STIHL authorized dealer. ► Maintain the blades as described in this In mowing operation, the robotic mower leaves User Manual. -
Page 14: Preparing The Mowing Area And Robot Mower For Operation
English 6 Preparing the Mowing Area and Robot Mower for Operation artificially generated voice output provide infor‐ mation about the current status of the robotic mower. If there is a confined section (6) in the mowing area, the robotic mower navigates the confined area, provided that a particular minimum width is maintained between the perimeter wires. -
Page 15: Positioning The Docking Station
► If you cannot carry out these steps: Do not use ► Where ground is hard and dry, slightly moisten the robot mower and contact a STIHL author‐ the mowing area to make driving the anchor‐ ized dealer for assistance. - Page 16 English 7 Positioning the docking station ► Select the location and set up the docking sta‐ ► Choose the docking station location so that tion as described. the following conditions are met: – The charging cable (1) can be installed out‐ Positioning the docking station within the mowing side of the mowing area to connect to a suit‐...
- Page 17 7 Positioning the docking station English Setting up the docking station in the center of the mowing area 90° The docking station is partially in the mowing area and the guide wire (1) can be routed for a =2 m in a straight line from the docking station to the mowing area.
- Page 18 English 7 Positioning the docking station Preparing the docking station Connecting the charging cable. NOTICE ■ In assembled condition, the plug connections of the charging cable are protected against contamination, e.g. dust and dirt. Contamina‐ tion of the plug connections may result in breakdowns of the docking station.
- Page 19 7 Positioning the docking station English ► Feed the perimeter wire through until it pro‐ trudes upward for a = 37 cm (length: ® 1x iMOW Ruler). ► Secure the charging cable (6) in the cable holder (7). ► Insert the plug (4). The plug (4) audibly and noticeably engages ►...
- Page 20 English 7 Positioning the docking station ► Route the perimeter wire (1) clockwise around the mowing area, If the docking station has been positioned partly in a navigable area and partly in the mowing area: ► Route the perimeter wire (1) 37 cm (length: ®...
- Page 21 7 Positioning the docking station English ► Route the perimeter wire (1) toward the front to the mowing area. The correct distance to the edge of the mow‐ ing area depends on whether the edge of the mowing area is navigable, or a distance of ®...
-
Page 22: Installing The Perimeter Wire
English 8 Installing the Perimeter Wire Installing the Perimeter Attaching perimeter wire and guide wire Wire General requirements Checking routing of perimeter wire and guide wire in the mowing area ► Use anchoring stakes to secure the perimeter wire and guide wire so that the following con‐ ditions are met: –... - Page 23 8 Installing the Perimeter Wire English Planning guide wire and routing connection point in the perime‐ ter wire Carefully plan the routing of one or several guide wires in advance. Take into account the position of all guide wires when installing the perimeter wire.
- Page 24 English 8 Installing the Perimeter Wire Corners ► If the angle is less than 90°: Split the angle. ► Design one corner with an angle greater Corners with a 90° angle than 90°. Then route the perimeter wire in a Corners with a 90°...
- Page 25 8 Installing the Perimeter Wire English ► Route 37 cm (length: 1x iMOW ► Route the perimeter wire at a distance of ® Ruler) of a = 1 m parallel to the drop-off edge. perimeter wire parallel to the unnavigable area.
- Page 26 English 8 Installing the Perimeter Wire 8.10 Confined section ► Route the perimeter wire (1) away from the edge toward the restricted area. Make sure that the following dimensions are maintained for the restricted area: – Minimum distance to other perimeter wires a = 55 cm ®...
- Page 27 8 Installing the Perimeter Wire English find its way through the confined section. Starting A corridor must be followed by a starting point (5) within the mowing area (B). Otherwise, the ® points can be set using the MY iMOW app.
- Page 28 English 8 Installing the Perimeter Wire ► Route the perimeter wire (2) parallel and Installing a corridor ® closely together for 37 cm (length: 1x iMOW ruler) to the main mowing area (A) without the perimeter wires crossing over each other. ►...
-
Page 29: Completing The Perimeter Wire Installation
(A) without the perimeter wires crossing. 8.14 Small Mowing Area The STIHL AKM 100 small area module must be used for a small mowing area where less than 20 m of perimeter wire is required. The STIHL AKM 100 stabilizes the wire signal and is incorporated into the perimeter wire by means of wire connectors. - Page 30 English 9 Completing the Perimeter Wire Installation ► Install the perimeter wire (1) in the base plate ► Route the perimeter wire (1) parallel and so that the guide wire lies flat in the cable duct closely to the other perimeter wire for 37 cm and is secured by the hook (4).
- Page 31 9 Completing the Perimeter Wire Installation English ► Insert the perimeter wire (1) into the left con‐ duit (6) and feed it through. Push the wire end (1) upward inside the docking station. ► Attach the perimeter wire (1) directly on the base plate (2) with a fixing pin (3).
-
Page 32: Installing Guide Wire
English 10 Installing Guide Wire 10 Installing Guide Wire 10.1 Installing guide wire Take into account the position of all guide wires when installing the perimeter wire. ► Take into account the general guidelines for installing the guide wire 8.2. ►... -
Page 33: Electrically Connecting The Docking Station
11 Electrically connecting the docking station English 11 Electrically connecting the docking station 11.1 Connecting perimeter wire and 90° guide wire ► Route guide wire (1) for at least e = 37 cm ® (length: 1x iMOW Ruler) in a straight line and at a right angle (90°) to the wire loop (7). - Page 34 English 11 Electrically connecting the docking station – The charging cable (1) is outside of the mowing area. – The charging cable (1) is routed so that people cannot trip over it. – The charging cable (1) is not under tension or tangled.
-
Page 35: Charging The Robot Mower
12 Charging the Robot Mower English ► Mount the power supply so that the following The LED (1) on the docking station lights up conditions are met: white. An LED (2) lights up white on the light strip – Suitable fixing materials. of the robot mower. -
Page 36: Light Patterns On The Robot Mower And Charging Station
English 14 Light patterns on the robot mower and charging station 14.2 LED on the docking station mobile device. In delivered condition, the radio interface is not password protected. ► Download the MY iMOW ® in the app store of your mobile device and create an account. -
Page 37: Stopping The Robot Mower And Activating The Device Lock
16 Stopping the robot mower and activating the device lock English Sending the robot mower to the docking station WARNING ► Press HOME (4). ■ The robot mower may unintentionally be The robot mower returns to the docking sta‐ switched on if the robot mower is not stopped tion. -
Page 38: Storing
(2) fully lights up red and finally flashes The battery has been installed in the robot red twice. mower and must only be removed by a STIHL The hibernation mode is activated. All extra authorized dealer. functions are deactivated. -
Page 39: Cleaning
If necessary, use a ph-neutral deter‐ station, charging cable and power supply can gent. STIHL recommends STIHL Multiclean. also be removed. ► Rinse off loose dirt with a gentle water jet. -
Page 40: Maintenance
English 20 Maintenance 20 Maintenance ► Turn the robot mower on its back. 20.1 Visual Inspection ► Regularly check the robot mower: – Cleanliness of the charging contacts – Check the hood and protective strip for damage – Check that the wheels run smoothly –... -
Page 41: Repairing
► Clean, blade disk (5), blade carrier (6) and ► Replace all blades. The blades cannot be nut (4). re-sharpened. ► If warning labels are illegible or damaged: Have the warning labels replaced by a STIHL authorized dealer. 21.2 Extending or repairing perime‐ ter wire or guide wire The perimeter wire or guide wire can be exten‐... -
Page 42: Troubleshooting
► If the fault persists: Do not attempt to fur‐ ther charge the robotic mower, remove the mains plug of the connecting cable from the socket outlet and contact a STIHL authorized dealer. 23 Specifications – Mowing speed ® – iMOW 5.0 EVO: 0.5 m/s... - Page 43 STIHL AAI battery – Protection class: III – Degree of protection: IP56 The battery has been installed in the robot – Maximum mowing area: mower and must only be removed by a STIHL ® – iMOW 5.0 EVO: 1500 m² authorized dealer.
-
Page 44: Spare Parts And Accessories
– Charging: 5°C to 40°C battery, which must be disposed of separately. – Use: 5°C to 40°C ► Return the robot mower to a STIHL authorized – Storage of robot mower: 0°C to 40°C dealer for disposal. – Storage of docking station and power supply: - The STIHL authorized dealer will remove the 20°C to 60°C... -
Page 45: Ukca Declaration Of Conformity
The technical documents are stored at ETSI EN 301 489-3 V 2.1.2 (2021-03), ETSI EN 303 447 V1.3.1 (2022-07), ANDREAS STIHL AG & Co. KG Product Appro‐ ETSI EN 301 489-52 V1.2.1 (2021-11), val. ETSI EN 301 511 V12.5.1 (2017-03), The year of construction, the country of manufac‐... -
Page 46: Open Source Software
ANDREAS STIHL AG & Co. KG, Open Source Team/Officer, Postfach 17 71, 71307 Waiblin‐ gen, Germany. We reserve the right to charge you the costs of the data carrier as well as ship‐... - Page 47 28 Open Source Software English 0458-012-0101-A...
- Page 48 *04580120101A* 0458-012-0101-A...