Table of Contents
Advertisement
Step 1. Attach the completed surround with
trim to theGas Insert. Modei '1-3821 haseight
(8) predrilled holes, four
(4)
per side at top and
bottom, to accept the surround. Using the
screwsprovided withthe Gas Insert, securethe
surround to the sides of the Gas insert (figure
42). For aiignment purposes, do not tighten
screws all the way.
Figure 42
Step 2. Push In on the surround till it is flush
against the front face of the Gas Insert and the
masonry fireplace. Centeras needed by sliding
left and right, then tighten screws.
Gas Conversion Kits
WARNING: THE CONVERSION KIT IS TO
BE INSTALLED BY AN AUTHORIZED OIS-
TRIBUTOR OR OTHER FACTORY CERTI-
FIE0 SERVICE TECHNICIAN I N ACCOR-
DANCE WlTH THE MANUFACTURER'S
INSTRUCTIONS ANO ALL CODES AND
REQUIREMENTS OF THE AUTHORITY
HAVING JURISDICTION. FAILURE TO
FOLLOW THESE INSTRUCTIONS COULD
RESULT I N SERIOUS INJURY OR PROP-
ERTY DAMAGE. THE QUALIFIED AGENCY
PERFORMINGTHIS WORKASSUMES RE-
SPONSIBILITY FOR THIS CONVERSION.
In Canada
I
THE CONVERSION SHALL BE CARRIED OUT
IN ACCORDANCE WlTH THE REQUIREMENTS
OF THE PROVINCIAL AUTHORITIES HAVING
JURlSOlCTlON AN0 IN ACCORDANCE WITH
THE REQUIREMENTS OF THE CAN1-6149.1
AND .2 INSTALLATION CODE.
Gzs
GG; , ; a i $ ; c ; ;
; d ; ; l ; L ; e
t2
z<;;;
,,G"7
Gas insert from the lise of one type of gas to the
useof another. These kits contain ailthe neces-
sary components needed to complete the task
includinq labeling that must be affixed to en-
suresafeoperation. Kit part numbers are l~sted
below and the following steps detailthe conver-
sion procedure
Conversion Kits
-
3" and 2" Venting
SFC
P I N
064125
-
Natural to Propane
SFC
PIN 066067
-
Propane to Natural
Conversion Kits
-
4"
and 6" Venting
SFC PIN 064129 -Natural
to Propane
SFC PIN 064126 -Propane to Natural
Step
1 .Turn olfthe
g a ~ s ~ p p l y t ~ t h e a p p l i a n ~ e .
Remove the front glass door frame from the
appliance. Open the lower controi compart-
ment door.
Step 2. Carefully remove the top twigs, then
remove the main logs. Exercise care as not to
break logs. Gather, remove and retain any
ember material on the floor of the appliance.
Step 3. Refer to page 6 of this manual and
remove the burner assembly and firebox bot-
tom plate.
Slep
4.
Modify the valve by replacing the
pressure regulator head!olluwing the instruc-
tions provided with the kit (figore 43 ).
Millivol: Valve
Figure 43
steps. Unscrewthe orificesfrom the manifold
outlets and replace them with the ones pro-
vided with the kit. See tables on page 11 and
Figure 28.
Figure 44
Step 7. Reassemble all removed components
by reversing the procedures outlined in the
preceding steps. Use pipe joint compound or
Teflon tape on all firtlngs before installing (en-
sure propane resistant compounds are used in
propane applications).
Step 8. Anachconversion kit label tothe rating
plate on the appliance. Refer to Figure 45for
iabeling details.
3"
and
2"
Venting
,
,
PRDPAHYLPG
,"*,,3,&,"*
~
urn
U * l o L " W'IUU.I
t v
OO>F#CE
$RE
-
'
3 2 ,
w,
i i
an;;jr
,
U B E L
A
LA8
m s
m-
" , ,
. , .
c-orm
LLBEL B
mrt
r
NATURAL GAS
,mu7 b,","n
~
,am
UIL
C
i l d t l
*
i
U**"LI
,nnua,
.
3.3.
Ls,,lcl
iiii
n,
,
i*,
Step 6. Replace the pilot orifice with the one
provided with the kit (Figure 44).
v
-
-
~
~
~
PROPANElLPG
IWU1
I,Y*/.
3s.m
NOTE OIAGVAMS
&
ILLUSlRATiONS NOT
TO %ALE
I
Hide quick links:
Advertisement
Table of Contents
