Sony DAV-HDX265 Operating Instructions Manual page 81

protection) compliant ("HDMI" on the front panel
does not light up). See page 94.
• If the HDMI OUT jack is used for vide() output,
changing the type of video signal output from the
HDMI OUT jack by pressing VIDEO FORMAT
rely solve the problem (plge 21).
Connect the TV and Ihe unit using a vide() jack
other than the HDMI OUT, and switch the TV_s
input to the connected vide() input so that you can
see the on-screen displays. Change the type of
video signal output from the HDMI OUT.iacL
and switch the TV's input back to HDMI. If the
picture still does not appear, repeat the steps and
try other options.
• You have selected "PROGRESSIVE" using the
VIDEO FORMAT button on the remote
/"PROGRE" lights up in the front panel display)
even though your TV cannot accept the
progressive signal. In this case. disconnect the
HDMI cord from the unit and then select
"INTERLACE"so that "PROGRE"turns off.
• lfthe signal flom the S VIDEO OUT jack is
distorte& change the type of video signal output
from the HDMI OUT jack by pressing VIDEO
FORMAT to [720 x 480p]" (page 21).
" Depending on the country, [72(}x 576p] may
appear.
Picture noise appears.
• The disc is dirty or Ila_ed.
• If the picture output from your system goes
through your VCR to get to your TV, the copy-
protection signal applied to some DVD programs
could affect picture quality. If you still experience
problems even when you connect your unit
directly to your TV, try connecting your unit to
your TV's S vide() input (page 2(1).
Even though you set the aspect ratio in [TV
TYPE] of [SCREEN SETUP], the picture does
not fill the TV screen.
• The aspect ratio on the disc is fixed.
Color irregularity occurs on the TV screen.
The subx_ oofcr and the front speakers in this system
are magnetically shielded to prevent magnetic
leakage. However,
some
leakage
may occur, as a
high-strength magnet is employed. If this happens,
check the following items:
• If the speakers are used with a CRT-based TV or
pr(_jector, install the speakers at least 0.3 meters
/ 1.0 fl) from the TV set.
• lfthe color irregularity persists, turn off the TV set
once, then turn it on after 15 to 30 minutes.
• If howling occurs, reposition the speakers farlher
away from the TV set.
• Make sure that no magnetic object (magnetic latch
on a TV stand, heahh care device, toy, etc.) is
placed near the speakers.
Sound
There is no sound.
• The speaker cord is not connected securely.
• Press MUTING on the remote if"MUTING ON"
is displayed in the front panel display.
• The system is in pause mode or in Slow-motion
Play mode. Press 1:::> to return to normal play
n/ode.
• Fast forward or fast reverse is perfonned. Press
[2:>- to return to normal play mode.
• Check Ihe speaker settings (page 76).
• The equipment connected to the HDMI OUT jack
does not conform to the audio signal fommt, in
this case set [AUDIO/HDMI)] in [CUSTOM
gETUP[ to [ON] (page 75).
No sound is output from the HDMI OUT jack.
• Set [AUDIO (HDMI)I in [CUSTOM SETUPI to
ION] (page 75).
• The HDMI OUT jack is connected to a DVI
(digital visual interface) device/DVI (digital
visual interface)jacks do not accept audio
signals).
• T U the following: (_) Turn the system off and on
again. (_) Turn the connected equipment off and
on again. (_) Disconnect and then connect the
HDMI cord again.
The left and right sounds are unbalanced or
reversed.
• Check Ihat the speakers and components are
connected correctly and securely.
There is no sound from the subwoofer.
• Check the speaker connections and settings (page
10, 76).
• Set the sound field to "A.F.D. STD" (page 30),
Severe hum or noise is heard.
• Check that the speakers and components are
connected securely.
• Check that the connecting cords are away from a
transformer or motor, and at least 3 meters ( 10 It)
away from your TV set or a fluorescent light.
• Move your TV away from the audio components.
• The plugs and.jacks are dirty. Wipe Ihem with a
cloth slightly moistened with alcohoh
• Clean the disc.
D.
D.
a"
continued_
81G8