Precautions; Description Of The Appliance; Identification; System Layout - Riello RBC-HP 1S Series Installation, Operation And Maintenance Manual

GENERAL INFORMATION

IDENTIFICATION

2 PRECAUTIONS

The operation of any appliance that uses electrical power de-
mands that a number of fundamental safety precautions be re-
spected. In particular:
0
Never attempt to install the system without using suitable
personal protection equipment and without following all
applicable occupational safety standards.
0
Do not touch the product when barefoot or wet if it has any
electrical accessories installed in it.
0
Never clean or service the storage cylinder without first
turning the mains power switch OFF to disconnect all elec-
trical accessories (if fitted) from the mains electricity supply.
0
Never pull, disconnect, or twist any electrical cables coming
from the appliance even if it is disconnected from the mains
electricity supply.
0
Do not expose the storage cylinder to the elements. It is not
designed for use outdoors.
0
Do not allow children or infirm persons to operate the sys-
tem unsupervised.
0
Do not dispose of packaging material into the environment,
or leave it within the reach of children, since it can become
a potential hazard. Dispose of packaging material in com-
pliance with applicable legislation.

3 DESCRIPTION OF THE APPLIANCE

R RBC-HP 1S storage tanks produce domestic hot water. They
come in six different models.
Their most important technical features are:
− the storage cylinder and coil are specially designed and
shaped for optimum performance in terms of stratifica-
tion, heat exchange and replenishment times
− internal glazing, bacteriologically inert, to ensure the
maximum hygiene of treated water, reduce limescale
deposits and make cleaning operations easier
− CFC-free polyurethane insulation and an elegant external
casing reduce heat loss
− using a flange for cleaning and inserting an extractable
coil
− using a magnesium anode with anti-corrosion function.
4 IDENTIFICATION
The R RBC-HP 1S solar heaters can be identified by:
Data plate
This lists the technical specifications and performance of the
product.
RIELLO S.p.A.
Via Ing.Pilade Riello 7
37045 Legnago (VR) - ITALY
BOLLITORE
BALLON
BOILER
Modello
Matricola
Modele
Fabrication
Model
Serial number
Codice
Code
Code
Massima potenza assorbita [T° Primario 80°C]
Puissance absorbée serpentin [T° Primaire 80°C]
Power absorbed by coil [T° primary 80°C]
Superficie serpentino
Surface serpentin
Coil heat exchange surface area
Press. esercizio max.
Pression service max.
Maximum working pressure of storage cylinder
Capacità del bollitore
Capacité ballon
Storage cylinder capacity
Potenza elettrica assorbita
Puissance élect. absorbée
Electrical consumption
Alimentazione elettrica
Alimentat. élect.
Power supply
Dispersioni secondo EN 12897
Déperditions selon EN 12897
Heat loss according to EN 12897
Collegamento di terra obbligatorio - Raccordement a la terre obligatorie
Obligatory ground connection
RIELLO S.p.A.
Via Ing.Pilade Riello 7
37045 Legnago (VR) - ITALY
Max pot. assorb.
Matricola
Puiss. absor. serp.
Fabrication
Power abs. by coil
Serial number
Anno
Modello
Année
Modele
Year
Model
Serial number plate
This specifies the serial number and model.
9
Technical data plate and Serial number plate are to be
applied (by the installer) after installation is complete.
9
If these plates or any other means of clearly identifying
the product are defaced, removed or lost, proper instal-
lation and servicing may be rendered difficult.

5 SYSTEM LAYOUT

5
1
2
3
1 Storage cylinder
2 Coil
3 Flange for heater in-
spection
4 Insulation
5 Cover
P Socket
M Guide
UAC Domestic hot water
outlet
12
T067773IFE
Anno
Année
Year
kW
l/h
m 2
bar
l
W
V-Hz
W
T067773IFE
kW
UAC
4
P
M
EAF
SB
EAF Domestic cold water
inlet
SB Storage cylinder drain