Advertisement
Available languages
Available languages
Installation
Instructions
Minimum
Clearance
Other Than Alcove or Closet Installation
Minimum clearance to combustible surfaces and for air opening are: 0 in. clearance both sides and rear. Consideration
must be given to provide adequate clearance for installation and service.
m PREPARING FOR INSTALLATION
OF NEW APPLIANCE
DISCONNECTING
GAS
TURN G AS
SHUT-OFF
VALVE
IC_-/_
DISCONNECT
AND DISCARD
OLD
_/_,_,
TO THE OFF
_
FLEXIBLE
GAS CONNECTOR
AND
POS,T,0N
OLDTRANS,T,ONDUCT,NG
MATERIAL.
REPLACE
WITH NEW
CSA(AGA)
APPROVED
FLEXIBLE
GAS LINE CONNECTOR
AND UL
APPROVED
TRANSITION
DUCT.
WARNING
- NEVER R EUSE OLD
FLE×IBLE CONN ECTORS.
The use of old flexible connectors can cause leaks and
personal injury. Always use new flexible connectors
when installing gas appliances.
REMOVING LINT FROM WALL
EXHAUST OPENING
• Remove and discard existing plastic or metal foil
transition duct and replace with UL listed transition duct.
_j
WALL
INTERNAL _t_,].DUCT
_
CHECK THATEXHAUST
OPENING -'_-_
\ G "'..
HOOD DAMPER O PENS
AND CLOSES FREE L Y.
TILTTHE APPLIANCE
SIDEWAYS AND REMOVE
THE FOAMSHIPPING PADS
BY PULLINGATTHE SIDES
AND BREAKINGTHEM AWAY
FROMTHE APPLIANCELEGS.
BE SURETO REMOVE ALL OF
THE FOAM PIECES AROUND
THE LEGS.
After the machine is in the home,
remove remaining packing material/
carton from washer.
DO NOT REMOVE SHIPPING ROD AT
THISTIME.
Removestyrofoam block. Removethe
bag containing the Washer hoses and
parts parts from tub. Put styrofoam
block back in tub opening to hold tub
in place during the rest of installation.
Hove washer close to final position.
Make sure there is at least a 24"
clearance on right side of washer to
remove shipping bar. PULLSHIPPING
BAR OUT USING YELLOW PLASTIC
HANDLE. Keep bar so it can be
reinstalled if washer is ever moved
again.
II
StyrofoamBlock
WashXer Hoses
and Parts
Yellow
"
Plastic
/
Handle
NEW HONE OR REMODELING FAUCETS/
DRAI N STAN DPIPE/ELECTRICAL LOCATIO N
Right side of
Laundry Center
12"-_
_ ..................
_|
Locate spigots,
"
drain standpipe
s3"
|
and electrical plug
|
!
in this area
!
FLOOR
I-_ GAS REQUIREMENTS
WARNING
, Installation
must conform
to local codes and
ordinances, or in their absence, with the National
Fuel Gas Code, ANSI Z223.1/NFPA 54, or the
Natural Gas and Propane Installation Code, CSA
B149.1
, This gas dryer is equipped with a Valve & Burner
Assembly for use only with natural
gas. Using
conversion
kit WE25H73
for
24" Models or
WE25H74 for 27" Models, your
local service
organization
can convert this dryer for use with
propane (LP} gas. ALL CONVERSIONS MUST BE
MADE BY PROPERLY TRAINED AND QUALIFIED
PERSONNELAND IN ACCORDANCE WITH LOCAL
CODESAND ORDINANCE REQUIREMENTS.
• Theappliancemust be disconnectedfrom the gas supply
piping systemduring any pressuretesting of that system
at a test pressurein excessof 0.5PSI(3A KPa).
• The appliance must be isolated from the gas supply
piping system by closing the equipment shut-off valve
during any pressure testing of the gas supply piping of
test pressure equal to or lessthan 0.5 PSI13.4KPa).
27" GASSUPPLY CONNECTION
3"
Note: 24" Gas supply
connection
has a flexible
hose thus dimensions
will vary.
4
Advertisement
