Existing Masonry Chimney - Vermont Castings Intrepid INDVRBDSB Installation & Operating Manual

Existing Masonry Chimney

3ULRU WR LQVWDOOLQJ WKH JDV VWRYH HQVXUH WKDW WKH H[LVWLQJ FKLPQH\ LV IXQFWLRQDOO\ VRXQG DQG FOHDQ
‡ +DYH WKH FKLPQH\ DQG DGMDFHQW VWUXFWXUH LQVSHFWHG DQG FOHDQHG E\ TXDOL¿HG SURIHVVLRQDOV +HDUWK
7HFKQRORJLHV UHFRPPHQGV WKDW 1), RU &6,$ FHUWL¿HG SURIHVVLRQDOV RU WHFKQLFLDQV XQGHU WKH GLUHFWLRQ RI FHUWL¿HG
SURIHVVLRQDOV FRQGXFW D PLQLPXP RI D 1)3$  /HYHO  LQVSHFWLRQ RI WKH FKLPQH\
‡ 5HSODFH FRPSRQHQW SDUWV RI WKH FKLPQH\ DQG ¿UHSODFH DV VSHFL¿HG E\ WKH SURIHVVLRQDOV
‡ 6HH 6HFWLRQ  IRU YHQWLQJ FRPSRQHQWV
Type A & B Co-Axial to Co-Linear
Co-Axial to
Co-Linear Connector
(Part 46DVA-GCL)
Type C - Up & Out Installation
TOP ADAPTOR
(Included in Masonry Chimney
Conversion Kit & LINK-STOVE Kit)
RETRO CONNECTOR
(Included in Masonry Chimney
Conversion Kit & LINK-STOVE Kit)
90° ELBOW
DIRECT VENT PIPE
(Length as required)
Figure 3.54
3131
Chimney Liner Termination Cap
(Included in Chimney Liner
Termination Kit)
3 in. (76mm) Flex Liner
(Included in Chimney Liner
Termination Kit)
Showing two 25 ft.
(9m) Sections of
Flex Liner
TERMINATION CAP
(Included in LINK-STOVE Kit)
FLASHING
(Included in Masonry
Chimney Conversion Kit &
LINK-STOVE Kit)
4 in. (102mm) FLEX LINER
(Included in LINK-STOVE Kit)
Vermont Castings • Intrepid DV-IFT Owner's Manual_R27 • 06/23
6HH &2$;,$/&2/,1($5 6HFWLRQ DQG )LJXUH 
Co-Axial to Co-Linear
Connector
(Part 46DVA-GCL)
Type D - Hearth Mount
Alcove Clearance to
Combustibles must be
maintained. See Figure 3.2.
Co-Axial to Co-Linear Connector
(Part 46DVA - GCL)
+RPH
Chimney Liner Termination Cap
(Included in Chimney Liner Termination Kit)
25 ft. (9m) of 3 in. (76mm) Flex
Liner Exhaust Section
(Included in Chimney Liner Termination Kit)
This section of the chimney
must be sealed
The chimney must be sealed from the
4 ft. (1m) section to termination using
a smoke shelf or a flue restrictor. The
seal should be a minimum of 6 in.
(152mm) below the end of the 4 ft.
(1m) Air Intake section.
4 ft. (1m) of 3 in. (76mm)
Flex Liner Air Intake Section
(Included in Chimney Liner Termination Kit)
Chimney Liner Termination Cap
(Included in Chimney Liner Termination Kit)
25 ft. (9m) of 3 in. (76mm) Flex
Liner Exhaust Section
(Included in Chimney Liner Termination Kit)
This section of the
chimney must be sealed
Chimney must be sealed
from 4 ft. (1m) section to
termination using a smoke
shelf or a flue restrictor. Seal
should be a minimum of 6 in.
(152mm) below end of 4 ft.
(1m) Air Intake section.
4 ft. (1m) of 3 in. (76mm) Flex
Liner Air Intake Section
(Included in Chimney Liner Termination Kit)
3-90-30007474