Gree GWH09AVCXB-K6DNA1B/I Owner's Manual page 22

Under humidity control with cooling mode,
humidity setting range for the remote controller:
40%-80%.
Temperature can be adjusted under humidity
control with cooling mode.
●
When smart dehumidification with cooling mode
is set, the remote controller will display "
the remote controller and indoor unit will display
"Ao" for 5 seconds.
Temperature can be adjusted under smart dehu-
midification with cooling mode.
● The humidity for smart dehumidification is auto-
matically adjusted according to human body
comfort; no need to set the humidity manually.
Under dry mode, press this button can select
humidity control with dehumidification mode, con-
tinuous dehumidification mode, general dehumidifi-
cation mode, and they can be set to operate circu-
larly.
humidity control with continuous dehumidification
dehumidification mode with dehumidification mode
● When humidity control with dehumidification mode
is set, the remote controller will display "
and humidity value "88"; you can press "+" and "-"
buttons to set the humidity value.
Humidity setting range for the remote control-
ler:30%-70%.
Temperature can't be adjusted under humidity
control with dehumidification mode.
When continuous dehumidification is set, the
●
remote controller will display "
controller and indoor unit will display "Co".
Temperature can't be adjusted under continuous
dehumidification mode.
● Under continous dehumidification mode, the unit
always works under dehumidification status; no
need to set temperature and humidity.
NOTE
●
The air conditioner is mainly used for controlling the te-
mperature, while the humidity control is the auxiliary fu-
nction. The humidity will be affected by the factors such
as indoor and outdoor environment, degree of indoor
sealing and indoor flow.
●
When the set humidity is higher than current atmospheric
humidity, the set humidity can't be reached.
●
I f the humidity sensor is with malfunction, humidity
s etting under cooling mode or dehumidification mode
will stop and the unit operates under general cooling
mode or dehumidification mode.
Press this button can select left & right swing angle.
Fan blow angle can be selected circularly as below:
" ;
general
dehumidification mode
", "%"
" ; the remote
Press this button, can select Sleep 1 (
(
between these, after electrified, Sleep Cancel is de-
faulted.
17
LR-swing button
no display
(stops at current
position)
NOTE
●
Press this button continuously more than 2s, the main
unit will swing back and forth from left to right, and
then loosen the button, the unit will stop swinging and
present position of guide louver will be kept immedi-
ately.
●
Under swing left and right mode, when the status is
switched from off to
2s later, status will switch to off status directly; if
press this button again within 2s, the change of swing
status will also depend on the circulation sequence
stated above.
●
This function only applicable for some models.
Timer button
At ON status, press this button once can set
TIMER OFF. The character of HOUR and OFF
will flash. Press "+" or "-" button within 5s can
adjust the time of TIMER OFF. After each
pressing of "+" or "-" button, time will increase or
decrease half an hour. When holding "+" or "-"
button, 2s later, the time will change quickly until
to reach to your required time. After that, press
"Timer" button to confirm it. The character of
HOUR and OFF won't flash again.
Cancel TIMER OFF: Press "Timer" button again
under TIMER OFF status.
At OFF status, press this button once can set
TIMER ON. Please refer to TIMER off for
detailed operation.
Cancel TIMER ON: Press "Timer" button again
under TIMER ON status.
NOTE
●
Time setting range: 0.5-24 hours.
●
Time interval between two operations can't exceed 5s.
Otherwise, remote controller will exit the setting status
automatically.
Sleep button
), Sleep 3 ( ) and cancel the Sleep, circulate
, if press this button again
), Sleep 2