System Registration; Programming The System Security Code; Registering The Handset To The Base; Basic Programming - Uniden 1660 Owner's Manual

SYSTEM REGISTRATION

PAGE
4
(SECURITY CODE)
PROGRAMMING THE
SYSTEM SECURITY CODE
All handsets must be programmed with the
SAME security code (Sec. Code) in order to
operate as a system. The first handset that is
programmed must be registered to the base
(see instructions below). Additional handsets
need only be programmed with the same
security code to begin operation.
1
PRG
Press (Program).
Press or (located on the side of
2
the handset) until " "
displays.
3 "#"
Enter to begin programming the
security code.
4 Using the keypad, enter any 6 digit
code.
NOTE:
Once you choose a security code for the first
handset, you must use the SAME code for each
additional handset. Don't worry about forgetting
the code- it can be displayed on the handset to
remind you of the code when you add additional
handsets.
OFF PRG
5 Press or to end the
programming session OR press
to advance to another
programming step.
NOTE:
Make sure you don't confuse the System Security
Code with the Handset ID number. Each handset
must have the SAME System Security Code, but
they must have DIFFERENT Handset ID numbers.
REGISTERING THE
HANDSET TO THE BASE
If you are programming the FIRST handset in
the system, you must register the new system
security code to the base unit.
1
Position the handset close (within 6-8
inches) to the base.
2
PRG
Press .
3
Press or until "
" displays.
4 PAGE
Press and hold on the base unit
for at least 3 seconds. The light will
begin to flash.
5
PAGE
Release .
"#"
6
Press on the handset. Keep
"#"
holding until a confirmation beep
is heard.
NOTE:
You don't need to hold both buttons (PAGE and
"#") at the same time. After you press and release
the PAGE button, then press the "#" button until
you hear the confirmation beep. If you don't hear
the beep after about 15 seconds, try repeating the
steps again.
or
7 OFF PRG
Press or to end the
programming session OR press
to advance to another
programming step.

BASIC PROGRAMMING

PROGRAMMING THE
HANDSET ID
Each handset must have a DIFFERENT
handset ID number. If any two handsets have
the same ID number, the entire system will
not function properly.
1
PRG
Press .
2 Press or until "
displays.
"#"
3 Press to begin programming the
Handset ID.
4
Enter a selected 2-digit station ID
number (choose any number from
11-70).
OFF PRG
5 Press or
programming session OR press
to advance to another
programming step.
TURNING THE RINGER
ON/OFF (L1 Ring)
You can turn the ringer on or off on each
handset.
1
PRG
Press .
Press or until "
2
displays.
or
3 The current setting will be displayed
on the second line of the display.
4 "#"
Press
"Off".
5 When the desired setting is displayed,
OFF
press
programming session OR press
to advance to another
programming step.
NOTE:
When the ringer is set to "Off", an icon will display
"
to alert you that the handset will not ring during
incoming calls.
RINGER TYPE
PROGRAMMING
to end the
or
The unit allows you to select one of four ring
tones for each handset. The ringer type
default is set to type 1.
1
PRG
Press
2
Press or
displays.
"#"
3
Press
of the four ring tones. Each time you
make a selection, you will hear the
corresponding ringer sound.
4 When the desired ringer type is
"
displayed, press
the programming session OR press
or to advance to another
programming step.
PAGE
5
to toggle between "On" and
PRG
or to end the
or
.
until " "
to toggle between any one
OFF PRG
or to end