Pioneer SX-P920 Operating Instructions Manual page 53

A.S.E.S. (Auto Synchro Editing System)
A.S.E.S. (systéme d'édition synchronisée automatique)
® When using the PD-P920M, the COMPU PGM func-
tion may not operate properly with discs that include
24 or more tracks.
1. Set discs in the CD player (PD-P720T/
PD-P920M). :
® When using the PD-P920M, load discs into maga-
zine trays 1 and 2.
2. Load a tape for recording into Deck Il.
Since recording always starts from the forward direc-
tion (®), be sure that the tape is loaded properly.
3. Set the DOLBY NR switch to the desired po-
sition.
4. Select the REV MODE switch.
==: For recording on only one side of a tape.
=> or @ : For consecutive recording on both sides
of a tape.
5. Press the COMPU PGM button of the CD player.
6. Within 3 seconds, use the Manual/Track search
buttons ( I¢4 <4, >> PP!) to designate the tape's
recording time.
> 46 > 54 > 60 - 74 > 90 ]
(minutes)
Tape recording time will change in the above sequence
each time the button is pressed.
® If you wish to designate the tape length in minute
intervals, set the remote control unit's CD/TUNER
switch to the CD position, then use the number
buttons to specify the tape length (from 1 to 99).
When specifying 1 to 9, first press 10/0/10. For
example, to specify 7 minutes, press 10/0/10, 7.
® Three seconds after performing step 5, the unit will
automatically be set to the COMPU PGM II mode.
If you wish to perform the COMPU PGM function
again, press the stop button ( @ ), then return to
step 5.
7. Press the COMPU PGM button of the CD play-
er (PD-P720T/PD-P920M).
Tracks will be programmed so that all tracks are
recorded on sides A and B, and the result will be dis-
played (PD-P920M).
When the COMPU PGM button is pressed, the track
numbers programmed on sides A and B will be dis-
played (PD-P720T).
8. Press the ASES button (FADE/FINE).
9. To stop the A.S.E.S.operation, press the stop
button (#) of Deck Il.
NOTE:
A.S.E.S. may stop or operate incorrectly when there is
'a song change near the end of the tape. In such cases
use manual operations to record the remaining songs.
COMPU PGM Il
® When the COMPU PGM Ilfunction is selected, the CD
player programs ail the tracks on the loaded disc, and
indicates the minimum length tape capable of hold-
ing all the tracks.
8.
9.
. Placer les disques dans le lecteur de CD
(PD-P720T/PD-P920M).
® Lors de l'utilisation du PD-P920M, charger des dis-
ques dans les plateaux de magasin chargeur 1 et 2.
Platine Il.
tion désirée.
sion (REV MODE).
de CD.
> 46 > 54 > 60 > 74 > 90
(minutes)
La durée d'enregistrement de la bande changera dans
enfoncée.
®@ Pour spécifier la longueur de la bande en interval-
les d'une minute, régler le sélecteur CD/TUNER de
I'unité de télécommande sur la position CD, puis
utiliser les touches numériques pour spécifier la lon-
gueur de la bande (de 1 & 99).
Pour spécifier de 1 a 9 minutes, appuyer tout
d'abord sur 10/0/10. Par exemple, pour spécifier
7 minutes, appuyer sur 10/0/10, 7.
de CD (PD-P720T/PD-P920M).
Appuyer sur la touche ASES (FADE/FINE).
Pour arréter l'opération A.S.E.S, appuyer sur la
touche d'arrét (@) de la Platine II.
REMARQUE :
manuel pour enregistrer les morceaux restants.
53
<ARE1211>
En/Fr