Bosch Professional GOP 18V-34 Original Instructions Manual page 22

22 | English
Accessory
ACZ 100 SWB
Starlock
100 mm diameter
bimetal segment
serrated knife for
multi-material
ACZ 105 ET
Starlock
105 mm diameter
carbide segment
saw blade for
multi-material
ACZ 85 RD4
Starlock
85 mm diameter
Diamond-RIFF seg-
ment saw blade for
mortar and abras-
ive materials
AVZ 70 RT4
Starlock
70 mm wide
carbide-RIFF mor-
tar remover
AVZ 90 RT2
Starlock
90 mm wide
carbide-RIFF delta
plate for mortar
and abrasive ma-
terials
AVZ 93 G
Starlock
93 mm wide sand-
ing plate for sand-
ing sheets of the
Delta 93 mm series
AUZ 70 G
Starlock
70 mm wide profile
sander for
70 × 125 mm
sanding sheets
AVZ 32 RT4
Starlock
32 × 50 mm
carbide-RIFF sand-
ing finger for wood
and paint
1 609 92A 8RD | (07.08.2023)
Material Application
Insulation material, insula- Precise cutting of soft materials;
tion boards, floor panels, example: Cutting insulation boards to size, cutting pro-
impact sound insulation truding insulation material to length so that it is flush with
boards, cardboard, car- the surface
pets, rubber, leather
Fibre cement boards, tile Separation and plunge saw cuts; also for sawing close to
joints, brick, fibreglass-re- the edge in difficult-to-access areas; long service life
inforced plastics, lamin- thanks to BOSCH Carbide Technology;
ate Example: Shortening already installed skirting boards or
door frames, milling cable ducts in brick, quick and low-
dust cutting out of tile joints, cutting fibreglass boards to
size for fittings, adjustment work in laminate
Cement joints, soft wall Cutting and separating in areas and corners that are close
tiles, fibreglass-reinforced to the edge or difficult to access, long service life thanks to
plastics, epoxy, GRP Diamond-RIFF;
Example: Removing joints between wall tiles for repair
work, recesses in tiles;
also available as Carbide-RIFF version: ACZ 85 RT3
Mortar, joints, epoxy Reaming and separating joint and tile material, as well as
resin, fibreglass-rein- rasping and sanding on a hard substrate; long service life
forced plastics, abrasive thanks to BOSCH carbide technology;
materials Example: Removing tile adhesive and grout
Mortar, concrete residue, Rasping and sanding on a hard substrate;
wood, abrasive materials, Example: Removing mortar or tile adhesive (e.g. when re-
paint placing damaged tiles), removing carpet adhesive
residues, removing paint residues;
available in grain sizes 20 (RT2), 40 (RT4), 60 (RT6) or
100 (RT10)
Depends on the sanding Sanding on edges, in corners or in difficult-to-access
sheet areas;
depending on sanding sheet, e.g. for sanding wood, paint,
lacquer, stone;
fleeces for cleaning and for structuring wood, removing
rust from metal and for abrading lacquers, polishing felt
for pre-polishing
Orbital stroke rate level "4" is the maximum level that
should be used when sanding. If the orbital stroke rate is
too high, this will considerably increase the wear of the ac-
cessory and can also lead to premature breakdown.
Wood, pipes/profiles, Convenient and efficient sanding of profiles and curved,
paint, varnish, filler, metal uneven material surfaces up to a diameter of 55 mm;
sanding sheets for sanding wood, pipes/profiles, varnish,
filler and metal
Wood, paint Sanding wood or paint in difficult-to-access places without
sanding paper; long service life thanks to BOSCH carbide
technology;
Example: Sanding down paint between window shutter
slats, sanding wooden flooring in corners;
available in grain sizes 40 (RT4) and 100 (RT10)
Bosch Power Tools