Table of Contents
Advertisement
REMOTE CONTROL OPERATION
Learning capacity and buttons that can learn
The buttons shown in the diagram can learn. By changing the
CONTROL MODE, a singie button can be used to learn a maximum of
nine commands, enabling a total of 261 commands to be learned.
However, the capacity for learning differs depending on the remote
control signal. With PIONEER
remote
control signals, about 70
commands can be learned.
CONTROL MODE
button
LEARN button
Learning function
button
[Learning procedure]
1. Press the LEARN button to switch to the LEARN mode.
2. Press one of the CONTROL MODE buttons.
3. Press one of the Learning function buttons.
4, Receive a remote control signal from another remote control
and fearn.
[Operation example]
As a learning example, an explanation follows on how io use the
CONTROL MODE VCR 1 | > | button to learn the VCR PLAY signal.
Place the transmission sections of the programmabie
remote
control unit and the remote control of the VCR facing each other.
NOTE:
Be sure to place the remote controls on a stable surface such as a
table while doing this. Also, avoid placing near fluorescent lighting
fixtures or in direct sunlight. When programming operations, use
new batteries.
1 to 2 inches
Place the two units on a table, separated by 2 to 5 cm (1 to 2
inches).
Memorization will not be possible if they are too close.
1. Press the LEARN button.
@ All the CONTROL MODE buttons flash at random.
2. Press the VCR 1 CONTROL MODE butten.
® Only the VCR 1 button flashes,
3. Press the |> | button.
® The VCR 1 button goes out, and lights after about one second.
lf you perform procedure 4 before the VCR 1 button lights,
correct learning is not possibile, so be sure to confirm that the
button is lit.
4. Press and hold the PLAY button on the VCR remote control.
@ When learning is completed, the VCR 1 button goes out, and all
the CONTROL MODE
buttons flash at random. The VCR iE]
button has learned the new signai.
During the learning operation, if you press the VCR [>] button
twice, or move
the remote controi, correct learning is not
possible.
To
continue
learning
with
other
buttons,
continue
from
procedure 2.
When it goes out,
learning has been compieted.
[When learning is not possible]
After the selected CONTROL
MODE
button (for example, VCR 7
flashes twice, and all the CONTROL MODE buttons flash, repeat the
learning operation from procedure 2.
[When learning is not possible because memory is full]
After the selected CONTROL
MODE
button (for example, VCR 1}
flashes four times, the LEARN MODE is canceled.
If the memory becomes full even when you have used only a small
number of buttons for learning, take the following steps.
* Try learning once more using the button that resulted in full
memory.
Memory may appear to be full even when it is not due to the two
remote controls being too far apart, not enough power remaining in
the batteries, or the effect of light from fluorescent lighting fixtures
or direct suntight.
@ Check buttons already used for learning.
if the CONTROL
MODE button remains lit after you have quickly
pressed and released a button used for learning, memorization in
that button is incorrect, resulting in the memory full condition. if you
perform learning once more, abnormal data is cleared, returning
you to normal conditions.
NOTE:
e After pressing the LEARN button, ifyou do not press a button within
about 30 seconds, the LEARN MODE is canceled.
® After pressing one CONTROL MODE button, if you da not press a
button that can learn within about
30 seconds, the LEARN MODE is
canceled. fa button other than a one that can learn is pressed, the
condition for CONTROL MODE button input is resumed.
° After pressing an operation button that can learn, if a remote
contral signal is not received within 45 secands, the LEARN MODE
is canceled,
[ EDIT
in the EDIT MODE, there is the PRESET MODE and MULTI-EDIT
MODE.
PRESET MODE (TV, VCR 1, VCR 2)
12 kinds of remote control signal formats are already preset for basic
TV and VCR functions. If they conform to your TV or VCR functions,
you can automatically preset operation buttons with the desired
format's remote control signals and use to commands operations.
Preset operation buttons are indicated in the diagram by 2224.
When you also want to use other buttons, use the LEARN operation
to memorize commands.
35
<ARB1489>
Advertisement
Table of Contents
